• Journal of Welding and Joining
• /
• 제6권4호
• /
• pp.16-26
• /
• 1988

The effect of carbon content on hot cracking of welded carbon steel was investigated Eight steel plates whose carbon content range from 0.02 to 0.23 percent were welded by autogeous gas tungsten are process. Constant strain was applied to the hot crack test specimen under the strain rate of 0.15 mm per second during welding. The hot cracking susceptibility ws high in the rnage of 0.02-0.05 and 0.12-0.23 percent carbon contents. The critical carbon content immune to hot cracking is in the range from 0.07 to 0.12 percent carbon. By electron probe microanalyser, amanganese segregation was not seen significantly in the whole carbon range. But segregation of silicon was higher in the region of low carbon contents. However, sulphur was segregated remarkably in the region betwen 0.18 and 0.23 percent carbon by peritectic reaction. Very smal lamount of dnedritic structure was observed in the region from 0.02 to 0.05 percent carbon by peritectic reaction. Very small amount of dendritic structure was observed in the region from 0.02 to 0.05 percent carbon but the predominant solidification structure was smooth by cellular growth. The higher the carbon content is, the more the columnar dendritic structure was observed.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.1317-1321
• /
• 2007

Aluminized steel sheet that Al coated on low carbon steel has a excellent heat resistance, thermal reflection and corrosion resistance. It has applied to fuel tank, automotive exhaust systems, etc. Laser weldability of the aluminized steel for the full penetration welding will be described in this paper. We focused on the effect of Al coating conditions on weld strength. For these objectives, aluminized steel sheets that has various thickness and coating weight were prepared for laser welding. And then, tensile-shear and hardness test were carried out. At that same time, Al content mixed in weld after laser welding was evaluated and investigated a correlation between the mixed Al and mechanical properties. Besides, as removing partially coating layer, weldability has been investigated according to position of coating layer. As a result of this study, as increasing Al content in weld, tensile-shear strength was decreased. Also it was identified that Al of coating layer caused grain growth.

• 한국생산제조학회지
• /
• 제20권6호
• /
• pp.720-728
• /
• 2011

Lap joint welding conducts low carbon steel plates using a 2.0kW continuous wave Nd:YAG laser beam. The specimen is composed of thin plate of 20 sheets. Process Variables contain two controlled parameters of the laser power and the welding speed. In order to quantitatively examine the characteristics of the lap welding, the welding quality of the cut section, stain-stress behavior, and the hardness of the welded part are investigated. The weld width difference between the top and the bottom because the welding speed is increased. The reason, cooling rate is decreased because of fast welding speed. When the heat input is higher, larger volume of the base metal will melt and the welding heat has longer time to conduct into the bottom from the top. The microstructure and tensile properties of the joints are investigated in order to analyze the effects of heat input on the quality of laser welded specimen. From the results of the investigation, We observe that welding quality is good for the laser power of 1800W, and laser welding speed from 1.8m/min to 2.2m/min.

• 한국기계가공학회지
• /
• 제17권3호
• /
• pp.16-21
• /
• 2018

The effect of heat treatment on the fatigue crack growth behavior in welded joints between the heat-affected zone (HAZ) of SA 508 Cl.3 low-alloy steel and HAZ of AISI 316L stainless steel is investigated. When the crack propagates across SA 508 Cl.3 or AISI 316L SS and HAZ into the weldment, the fatigue crack growth rate (FCGR) in the HAZ region does not change or decrease despite the increase in stress intensity factor ${\Delta}K$. The residual stress at the HAZ region is more compressive than that at the base Δ materials and weldment. The effect of the welding residual stress on the crack growth behavior is determined by performing a residual stress relief heat treatment at $650^{\circ}C$ for 1h and subsequent furnace cooling. The FCG behavior in the HAZ region in the as-welded specimen and the residual stress relief heat-treated specimen is discussed in terms of the welding residual stress.

• 대한기계학회논문집A
• /
• 제34권6호
• /
• pp.709-715
• /
• 2010

수소 확산과 탄-소성 거동이 결합된 모델은 이미 제시되어 있다. 본 논문에서는 수소확산에 미치는 인자들과 그 영향에 대해 연구하였다. 각 인자들의 영향을 비교하기 위해 저탄소강 재료의 균열이 있는 무한 평판 모델에 대해 수소확산과 기계적 하중이 연계된 유한요소 해석을 수행하였다. 유한요소 해석 결과는 Taha와 Sofrinis의 연구(2001) 결과와 비교하여 검증하였다.

• 한국레이저가공학회지
• /
• 제2권2호
• /
• pp.34-41
• /
• 1999

A RS840 $CO_2$laser and a powder auto-feeding apparatus have been used to deposit single tracks of Ni-base superalloy on low carbon steel. In this paper, the effects of laser cladding parameters on clad geometry, dilution and microhardness are studied. As a results, the w/h ratio of the clad layer increases with decreasing powder feed rate and increasing laser scan speed. Increase of powder density and decrease of specific energy have little effect on dilution. It was found that the clad layer of the highest hardness has a structure in which fine and leaf like phases are dispersed in ${\gamma}$Ni matrix.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 추계학술대회 논문집
• /
• pp.332-335
• /
• 2005

A model is developed to quantitatively analyze the dilatometry curve of carbon steel for the evaluation of phase fraction during transformation. The effect of anisotropic volume change due to transformation mismatch plasticity as well as carbon enrichment in austenite during the transformation is considered in the developed model. The developed model is applied for the analysis of dilatometry curves of carbon steels. The result shows that considering the anisotropic dilatation is very essential to quantitatively evaluate the phase fraction from the dilatation curve.

• Journal of Welding and Joining
• /
• 제2권1호
• /
• pp.58-65
• /
• 1984

NGW(Narrow Gap Welding)는 개선폭이 약 9mm로서 연강 및 저탄소강을 용접할 경우 두께가 300mm까지 1층으로 용접이 가능하다. 따라서 두께가 두꺼운 발전설비, 원자력 설비, 화학 설비 등의 압력용기의 용접에 적합한 용접법이다. 그러나 실제적인 NGW의 적용은 제작자의 친근 감의 결여, 기술 부족 및 복잡성 등의 이유로 아직도 비교적 널리 활용되지 않고 있다. 새로운 type의 GMAW-NG process가 발전되어 오고 잇다. 위와 같은 장점과 단점을 비교해 볼 때 낮은 operating 경비, 높은 joint filling rate, 변형과 잔류 응력의 감소 등으로 세계적인 용접 전 문가들의 계속적인 관심도가 높아지고 사용도도 증가하고 있다. narrow gap welding의 장단점을 요약하면 아래와 같다. 장 점 1) 생산성이 높다. 2) 고품질을 얻을 수 있다. 3) 잔류 응력과 변형을 적게 한다. 4) 전자세 용접이 가능하다. 단 점 1) 용접기의 가격이 비싸다. 2) 용접 품질에 큰 영향을 주는 아아크가 작업 조건에 따라 민감하게 변한다. 3) repair procedure는 다른 용접 방법을 요구한다. 4) 과도한 복잡성 때문에 장비의 신뢰성이 낮다.

• 대한조선학회지
• /
• 제10권2호
• /
• pp.9-18
• /
• 1973

The effects of carburization on the fatigue strength and cracks were studied. The fatigue phenomena of the carburized specimens were compared with noncarburized specimens those were either heat-treated or un-treated. The fatigue strength of these specimens were measured by rotating bending fatigue machine. The obtained results indicated that the fatigue strength of carburized specimens were increased ranging from 24-59 % than those of un-treated, and 22-38% than those of heat-treated. The Vickers hardness of carburized were also increased as much as 138-195% than those of un-treated, and 42-125% than those of heat-treated. The microscopic observation of the carburized specimens mostly composed of minute pearlitic structure at hard case exhibited to have more localized slip than those of non-carburized specimens.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2011년도 춘계 학술논문 발표대회 1부
• /
• pp.59-60
• /
• 2011

The purpose of this study is to produce the low-carbon eco-friendly inorganic composite at room temperature by an alkali accelerator without firing process at high temperature, and complement the problem of previous studies, the deterioration in strength caused by cracking, with incorporation of PVA fibers. Results of reviewing the changes in the strength properties of PVA showed that test body mixed with PVA fibers had the superiority in strength expression.