• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.32 no.2
• /
• pp.155-162
• /
• 2022

The SITM (See-In-The-Middle) attack proposed in CHES 2020 is a type of analysis technique that combines differential cryptanalysis and side-channel analysis, and can be applied even in a harsh environment with a low SNR (Signal-to-Noise Ratio). This attack targets partial 1^st or higher order masked block cipher, and uses unmasked middle round weakness. PRESENT is a lightweight blockcipher proposed in CHES 2007, designed to be implemented efficiently in a low-power environment. In this paper, we propose SITM attacks on 14-round masked implementation of PRESENT while the previous attacks were applicable to 4-round masked implementation of PRESENT. This indicates that PRESENT has to be implemented with more than 16-round masking to be resistant to our attacks.

• Journal of Korea Society of Industrial Information Systems
• /
• v.15 no.1
• /
• pp.1-14
• /
• 2010

It is recently issued scalability, mobility and external internet connection on Wire-less sensor network. The low power wireless sensor networks based on IPv6 technology 6LoWPAN technology is being standardized in the IETF. This paper for the 6LoWPAN environment based on the routing protocol LOAD, route cost applied the packet re-transmission rate which follows in Link Qualities price which uses at course expense and packet transmission Minimum route Cost routing protocol where does on the course wherethe smallest packet re-transmission becomes accomplished proposed. The technique which proposes compared and LOAD and AODV that about 13%, about 16% energy consumption is few respectively averagely, Energy of the entire network equally, used and energy effectiveness and improvement of network life time experiment led and confirmed.

• The Journal of the Convergence on Culture Technology
• /
• v.9 no.4
• /
• pp.699-706
• /
• 2023

Recently, the 4 generation industry revolution is developed with advanced and combined with a variety of new technologies. Conventional healthcare system is applied with IoT application. It provides many advantages with mobility and swift data transfers to patient and doctor. In despite of these kinds of advantages, it occurred security issues between basic devices and protocols in their applications. Especially, internet of things have restricted and limited resources such as small memory capacity, low capability of computing power, etc. Therefore, we can not utilize conventional mechanism. In this paper, we analyzed attacks and vulnerability in terms of security issues. To analyze security structure, features, demands and requirements, we solve the methods to be reduced security issues.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.4
• /
• pp.1926-1934
• /
• 2013

M2M (Machine-to-Machine Communication) refers to technologies that allow wired and wireless systems to communicate with other devices with similar capabilities. M2M has special features which consist of low electricity consumption, cheap expenses, WAN, WLAN and others. Therefore, it can communicate via a network. Also, it can handle itself without a person's management. However, it has a wireless-communicate weakness because of the machine-communicate request, and also it is difficult to administrate and control each other. So In this Paper, It suggests the safety protocol between Device, Gateway and Network Domain in M2M environment. Proposed protocol is based on ID-Based encryption's certificate and creates session key between the Access Server and the Core Server in the Network Domain. It uses that session key for sending and receiving data in mutual, and adds key renewal protocol so it will automatically update discern result. a comparative analysis of the existing M2M communication technologies and PKI-based certificate technology is compared with the proposed protocol efficiency and safety.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39A no.5
• /
• pp.271-279
• /
• 2014

In this paper, the two design techniques of the embedded system which provides a wireless image observation with temporary ad-hoc network are proposed and developed. The first method is based on the embedded system design technique for a nearly real-time wireless short observation application, having a specific remote monitoring node with a built-in image processing function, and having the maximum rate of 1 fps (frame per second) wireless image transmission capability of a $160{\times}128$size image. The second technique uses the embedded system for a general wireless long observation application, consisting of the main node, the remote monitoring node, and the system controller with built-in image processing function, and the capability of the wireless image transmission rate of 1/3 fps. The proposed system uses the wireless ad-hoc network which is widely accepted as a short range, low power, and bidirectional digital communication, the hardware are consisted of the general developed modules, a small digital camera, and a PC, and the embedded software based upon the Zigbee stack and the user interface software are developed and tested on the implemented module. The wireless environment analysis and the performance results are presented.

• The Journal of Korean Institute of Information Technology
• /
• v.15 no.12
• /
• pp.157-164
• /
• 2017

Mobile ECG signal measurement is a technique to measure small signals of several mV, and many studies have been conducted to remove noise including wandering scheme. Removal of the equipotential line noise caused by shaking or movement of the electrode cable is one of the core research contents for the electrocardiogram measurement. In this study, we proposed a modified step-size of combined NLMS(normalized least squares) and DLMS(delayed least squares) adaptive filter to eliminate baseline noise from ECG signals. The proposed method mainly adjusts initial filter step-size to reduce distortion of original ECG signals characteristic after eliminating baseline noise. The modified filter step-size is scaled by filter order size and distortion minimization factor. This method is suitable for portable ECG device with a small processor and less power consumption. This technique also decreases computation time which is essential for real-time filtering. The proposed filter also increase the signal to noise ratio (SNR) compared to conventional NLMS filter.

• Journal of the Korea Society for Simulation
• /
• v.18 no.3
• /
• pp.73-82
• /
• 2009

Due to the many advantages including low price, low power consumption, and miniaturization, the CMOS camera has been utilized in many applications, including mobile phones, the automotive industry, medical sciences and sensoring, robotic controls, and research in the security field. In particular, the 360 degree omni-directional camera when utilized in multi-camera applications has displayed issues of software nature, interface communication management, delays, and a complicated image display control. Other issues include energy management problems, and miniaturization of a multi-camera in the hardware field. Traditional CMOS camera systems are comprised of an embedded system that consists of a high-performance MCU enabling a camera to send and receive images and a multi-layer system similar to an individual control system that consists of the camera's high performance Micro Controller Unit. We proposed the SL-AVS (Small Size/Low power Around-View System) to be able to control a camera while collecting image data using a high speed synchronization technique on the foundation of a single layer low performance MCU. It is an initial model of the omni-directional camera that takes images from a 360 view drawing from several CMOS camera utilizing a 110 degree view. We then connected a single MCU with four low-power CMOS cameras and implemented controls that include synchronization, controlling, and transmit/receive functions of individual camera compared with the traditional system. The synchronization of the respective cameras were controlled and then memorized by handling each interrupt through the MCU. We were able to improve the efficiency of data transmission that minimizes re-synchronization amongst a target, the CMOS camera, and the MCU. Further, depending on the choice of users, respective or groups of images divided into 4 domains were then provided with a target. We finally analyzed and compared the performance of the developed camera system including the synchronization and time of data transfer and image data loss, etc.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2011.05a
• /
• pp.85-85
• /
• 2011

홍수기에 안전하고 정확한 유량측정을 통하여 물관리에 필요한 기초수문자료를 확보하고자 한국수자원공사에서 1993년도부터 홍수유량측정기술 확보를 위한 연구를 시작하였다. 그간의 연구성과를 바탕으로 1999년도에 하천의 유속을 비접촉식으로 측정할 수 있는 홍수용 전자파표면유속계를 개발하여 특허등록하였고 그와 동시에 이의 상품화를 추진하여 2010년도까지 75대를 보급하여 실무에서 이용하고 있다. 이동식인 홍수용 전자파표면유속계를 바탕으로 2001년도에는 고정식 실시간 홍수유량측정측정시스템을 개발하여 특허등록하였고, 이 시제품을 현재 용담 수자원시험유역의 동향지점에서 시험운영하고 있다. 또한, 현장 유량측정실무자들의 홍수용 전자파표면유속계 개선요구에 따라 편각용 전자파표면유속계 시제품을 개발하였으며, 이는 임의의 한 지점에 설치한 한 대의 장비로 좌우 여러 측선의 유속을 동시에 측정할 수 있는 다점 측정기능을 갖도록 성능을 개선하였다. 이에 따라 홍수시 유량측정에 소요되는 시간이 줄어들어 신속하게 유량측정을 완료할 수 있는 계기를 마련하였다. 이와 더불어 유속측정 범위를 확장하여 홍수시의 고유속 뿐만 아니라 0.5 m/s 이하의 저유속까지 측정할 수 있는 범용 전자파표면유속계의 시제품을 추가로 개발하였다. 이 장비는 최저유속 0.03 m/s의 측정을 실내시험을 통하여 입증하였다. 범용 전자파표면유속계는 상품화 시제품의 개발을 목표로 기존 시제품의 현장시험을 통하여 현장적용상의 문제점에 대한 해결에 주력하였다. 첫째, 평갈수용 전자파표면유속계의 사용편의를 개선하기 위하여 소형화 및 경량화를 추진하였고, 이를 위하여 사용주파수를 기존의 10 GHz에서 24 GHz로 변경함으로써 $35{\times}35\;cm$ 크기의 기존안테나를 $22{\times}22\;cm$ 크기로 소형화하였으며 송수신부의 무게는 기존 18 kg에서 3.3 kg으로 혁신적으로 줄이는데 성공하였다. 이를 위하여 안테나는 기존의 반사형안테나에서 도파관슬롯배열안테나로 변경하였다. 둘째, 측정값의 안정화를 위하여 안테나의 특성을 개선하여 부엽(side-lobe) 레벨 30 dB 이하 그리고 전후방비(front-back ratio) 50 dB 이하로 개선하여 안테나가 지향하는 방향 이외의 위치에서 반사되는 불필요한 신호를 줄였다. 또한 적응형 이득제어(adaptive gain control)기법의 채택으로 미소 신호에 대한 안정적 측정 및 과다 신호에 대한 능동적 감쇄를 할 수 있도록 시스템을 구성하여 전 유속범위에 대한 안정적 측정을 가능토록 설계 및 제작하였다. 셋째, 자가점검 기능을 탑재하여 유속측정 전에 기기의 상태에 대한 self test기능을 통하여 측정자가 기기의 상태를 사전에 파악 가능토록함으로써, 기기 오작동에 대한 능동 대처할 수 있도록 하였다. 이외에도 저전력 회로설계를 통하여 배터리 사용시간을 확장하였고, 기존의 전자파표면유속계가 가지고 있던 방습 및 방수에도 내성을 갖는 제품으로 설계하였으며 스마트기기를 이용한 무선측정 및 세련된 디자인 등 사용자의 요구사항을 충분히 반영하였다.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.23 no.6
• /
• pp.739-745
• /
• 2017

Many studies have been conducted to reduce environmental pollution by ships and reduce fuel consumption. As part of this effort, research on power conversion systems through DC distribution systems that link renewable energy with conventional power grids has been pursued as well. The diode rectifiers currently used include many lower harmonics in the input current of the load and distort supply voltage to lower the power quality of the whole system. This distortion of voltage waveforms causes the malfunctions of generators, load devices and inverter pole switching elements, resulting in a large number of switching losses. In this paper, a controller is presented to improve DC output waveforms, the input Power Factor and the THD of an AFE type PWM rectifier used for PLL. DC output voltage waveforms have been improved, and the input Power Factor can now be matched to the unit power factor. In addition, the THD of the input power supply has been proven by simulation to comply with the requirements of IEEE Std514-2014.

• Proceedings of the Korean Information Science Society Conference
• /
• 2005.11a
• /
• pp.175-177
• /
• 2005

무선 센서 네트워크에서는 배터리에 의존하는 수많은 센서 노드들로 구성이 된다. 이때, 물체들을 감지하기 위해서는 센서들은 켜져 있어야 하고, 수집한 데이터는 클러스터 헤드(Cluster Head)나 싱크(sink) 로 보내주어야 한다. 일련의 동작을 위해서 센서들은 않은 에너지를 소모하게 된다 이를 보완하기 위해서 LEACH 라는 방법을 이용하여, 클러스터 헤드 만이 싱크로 데이터를 전송하고, 에너지를 균일하게 소모하기 위한 기법을 사용한다. 본 논문에서는 기본적으로 LEACH 방법을 이용하면서, 이동체의 이동을 감지함에 있어서, 이동체의 예상 이동영역을 예측하여, 예상 이동영역내에 존재하지 않는 센서 노드들은 다음 라운드가 시작할 때까지 Sleep 하도록 하고. 예상 이동영역내에 있는 센서 노드들만 감지하도록 하여, 에너지의 소모를 줄였다. 이때 예상 이동영역은 싱크가 이전에 수집한 데이터로 계산하여, 이동체들의 정보를 모든 노드들에게 브로드 캐스트(Broadcast)하고, 매 라운드마다 클러스터 헤드선택까지는 LEACH 와 마찬가지로 모든 센서 노드들이 참여하지만, 이후 클러스터의 구성원이 되기 위해서는 예상 이동영역내에 존재해야 한다. 만약 해당 라운드에서클러스터 헤드가 되어도, 구성원이 존재하지 않는 다면 다시 Sleep 하도록 하여, 에너지 소모를 줄였다.