• Resources Recycling
• /
• v.17 no.1
• /
• pp.43-50
• /
• 2008

In this study, we carried out the research on triboelectrostatic separation for materials separation of PET & Nylon recovered to waste plastic beer bottle. From the research on charging characteristic for choice of charging materials, it was found that PMMA was optimum charging material to make high charging amount with opposite polarity for PET & Nylon in waste plastic beer bottle. Therefore, we manufactured a charger of pipe line and cyclone type using PMMA material for separation of PET and Nylon. At optimum test conditions that used PMMA pipe line and cyclone charger developed in this study, we developed a triboelectrostatic separation technique that can separate PET plastic up to grade of 99.6% and recovery of 88.2%. We established new separation technology that can recycle the PET and Nylon recovered from waste plastic beer bottle.

• Explosives and Blasting
• /
• v.25 no.2
• /
• pp.23-33
• /
• 2007

It is difficult to measure a blast noise in the vicinity of tunnel blasting works and the effect of lowering noise changes very highly with types of soundproof materials. So, the main interest of this study focuses on the materials of a soundproof facilities and the method of noise forecast in a near distance. 20 types of the soundproof facilities are established and blast noise is generated using firecracker in a Hume concrete pipe. To analyze the variations of magnitudes of noise and frequency with the soundproof materials and types, the noise and frequency is measured in a short distance next to blast area.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.9
• /
• pp.985-991
• /
• 2008

This paper presents a novel balanced mixer receiver front-end design based on a metamaterial structure applicable to differential-/common-mode excitation. This metamaterial structure functions as a leaky-wave antenna and provides in-trinsic common-mode suppression. Low LO leakage and high RF to LO isolation are achieved without additional filters for LO and RF paths. The metamaterial is based on a unit-cell which under a differential-mode excitation behaves like a composite right/left-handed(CRLH) metamaterial. In contrast, the metamaterial unit-cell is below cut-off under a common-mode excitation. Experimental results are used to verify the proposed metamaterial's differential-/common-mode characteristics. The metamaterial is integrated with a balanced mixer design resulting in an operation frequency range of $1.96{\sim}2.40$ GHz with an optimum mixer conversion loss of 21.1 dB at 2,4 GHz.

• The monthly packaging world
• /
• s.263
• /
• pp.109-119
• /
• 2015

환경부는 '제품의 특성상 낱개로 포장'이 필요한 경우에 Tea-bag, 색깔구분이 필요한 점토류 완구에 대한 개별포장을 포함하여 현재 포장기술에 부합하는 제도로 개선하고자 "제품의 포장재질 및 포장방법에 대한 간이측정방법" 고시 일부 개정안을 발표했다. 본 고에서는 주요 개정 내용과 함께 측정방법에 대해 자세히 살펴보도록 한다.

• 선박안전기술공단연구보고서
• /
• s.1
• /
• pp.1-146
• /
• 2007

본 연구의 목적은 STS 304 프로펠러축의 육성가공 및 STS 630 프로펠러축의 열 가공에 따른 강도 및 내식성 등의 재질특성변화 등을 조사 분석하여 선박기관기준 제8조 제2항에서 규정하고 있는 ‘용접수리 불가’에 대한 근거자료 제시(동조동항의 단서조항에 대해서는 일반적으로 알려진 스테인리스강의 용접에 대한 적정방법 이외에 연구결과를 바탕으로 적정 기준을 제시할 수 있는지에 대한 부분도 동시에 검토 하고자 함)는 물론, 선박기관기준 제65조 제1호(총 톤수 20톤 이상의 경우는 제59조 제1항 적용)에서 규정하고 있는 석출경화계 스테인리스강의 제1종축으로써의 인정 여부에 대한 유효성을 제시하여 프로펠러축의 가공(육성․열)과정에 필요한 기본 방향을 제시하고자 함. 따라서 본 연구에서는 STS 304, STS 630 프로펠러축의 가공에 따른 결과를 바탕 으로 위에서 언급한 사항들에 대한 근거자료 확보 및 프로펠러축의 가공에 따른 방향을 제시하기 위한 일환으로 ‘스테인리스강 프로펠러축의 가공에 따른 재질 특성에 관한 연구’를 실시함으로써 프로펠러축 검사와 관련한 평가 기준 정립의 근본적인 지침 자료를제시하고자 함. 또한 본 연구과제는 스테인리스강 프로펠러축에 대한 가공(육성․열) 특성을 살펴 봄으로써 기존에 이미 발표된 판 형태의 스테인리스강 용접에 대한 연구와는 다소 구별되는 과제일 뿐만 아니라 단순한 스테인리스강의 용접특징을 나타낸 실험들과는 다르게 스테인리스강 프로펠러축에 대한 특징들을 분석하고 평가함으로써 현장중심의 연구가 될 수 있도록 하였음. 이번 연구의 결과는 일반적으로 알려진 스테인리스강의 용접관련 특성들을 통해어느 정도의 결과 추정은 가능하나 앞에서 언급한 기준들에 대한 구체적인 근거자료를 확보하여 필요시 적절하게 활용할 수 있는 자료가 될 수 있도록 하고자 하였음.

• Computational Structural Engineering
• /
• v.8 no.3
• /
• pp.79-89
• /
• 1995

Two-element plate concept is incorporated into the buckling problem in order to simplify the nonlinear distribution of stress through the thickness of plate. Finite element formulations and programs based upon the Reissner functional and the modified Reissner functional using two-element plate concept are developed for buckling analysis of plates under axial compression. The two programs have been applied to obtain the linear elastic buckling behavior of axially compressed flat plates. Excellent agreement of linear elastic-solution results with exact or approximate solutions of other authors for the same boundary conditions proves the validity of the finite element method using two-element plate theory.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1997.05b
• /
• pp.384-389
• /
• 1997

고분자 촉매 담체인 스티렌-디비닐벤젠의 제조시 중합반응 개시제의 함량에 따른 영향과 반응기의 재질에 따른 영향을 수소흡착실험을 통하여 확인하였다. 담체의 중합반응시 제조조건이 동일하다 할지라도 개시제의 함량에 따라서 담체의 기공 특성이 달라지므로 개시제의 함량은 모노머 양의 1%를 사용한 시료가 수소흡착능이 가장 좋은 것으로 나타났다. 반응기의 재질은 teflon으로 직접 제조한 것보다는 teflon으로 코팅 처리한 것이 더 수소흡착능이 좋은 것으로 확인되었다.

• Journal of Korean Society of Environmental Engineers
• /
• v.31 no.9
• /
• pp.747-752
• /
• 2009

This research was performed by means of several different virgin granular activated carbons (GAC) made of each coal, coconut and wood, and the GACs were investigated for an adsorption performance of bromate in a continuous adsorption column. Breakthrough behavior was investigated that the breakthrough points of the virgin two coals-, coconut- and wood-based GACs were observed as 9252 bed volume (BV), 6821 BV, 5291 BV and 2431 BV, respectively. The experimental results of adsorption capacity (X/M) for bromate showed that two coal- based GACs were highest (1334.5 and 798.2 ${\mu}g$/g), the coconut-based GAC was intermediate (668.6 ${\mu}g$/g) and the wood-based GAC was lowest (156.8 ${\mu}g$/g). The X/M of the coal-based GACs was 2~8.5 times higher than the X/M of the coconut-based and wood-based GACs. The results of carbon usage rates (CURs) for the virgin two coal-, coconut- and wood-based GACs were shown as 0.19, 0.25, 0.33 and 0.71 g/day respectively. The adsorption capacity, k values, were also investigated by means of the GACs for bromate. The k values of two coal-, coconut- and wood- based GACs for bromate were found to be 121.3, 76.7, 43.3 and 14.6 respectively. This results suggested that using the virgin GAC made of coal was the best selection for removal of bromate in the water treatment for an advanced treatment.

• Journal of Conservation Science
• /
• v.26 no.1
• /
• pp.33-41
• /
• 2010

The archival objects are tangible evidence reflecting public work as forming archives which are administrative, historic, symbolic, cultural and artistic value. They are produced from the various countries so that they have different material and manufacture techniques. However there are difficulties in conservation and management because the material investigation and conservation management system are not established. Therefore this research presents fundamental data for the efficient conservation management by material investigation and condition check metal archival objects. Among the public official presents made of metal, 12 pieces which are discoloration, oxidation, loss or crack are chosen for this research. In order to examine extensive condition of metal archival objects, the condition check card used from the domestic museum and the national museum in Japan are collected and then the new check card is produced. X-ray is used to know the making technique, binding means between different material. Portable-XRF is also used for the chemical composition analysis of metal archival objects, and then classifying respectively according to their material. As a result of condition check, it is possible to investgate the appearance character, deteriorated parts and weak parts of structure. Also P-XRF could find out the composition of metal archival objects which is different from existing condition check card. Therefore the research results can be used as fundamental data for further conservation and management as well as long-term conservation.

• Resources Recycling
• /
• v.22 no.6
• /
• pp.33-40
• /
• 2013

Due to the environmental problem caused by plastics largely used in various fields, the importance of recycling is being emphasized. A research on material separation of ABS and PS mixed plastic waste, using a triboelectrostatic separator, was carried out for recovery the ABS. As a results of research on charging characteristic for choosing charging material, it was confirmed that ABS was optimum charging material for a tribo-charger in the material separation of ABS and PS. In the material separation using ABS charger, ABS grade of 99.5% and recovery of 92.5% were achieved at 20 kV, splitter position +2 cm from the center and 30% relative humidity. Therefore, material separation technique for recycling ABS and PS mixed plastic waste was established.