• 한국신재생에너지학회:학술대회논문집
• /
• 2005.11a
• /
• pp.405-413
• /
• 2005

본 연구에서는 3톤/일의 플라스틱 투입량을 기준으로 혼합폐플라스틱으로부터 대체연료유를 생산할 수 있는 소용량 중심의 폐플라스틱 유화설비를 설계 제작하였으며 장기간에 걸친 시운전을 통하여 유화설비의 운전성 평가에 대한 실증연구를 수행하였다. 대상 폐플라스틱으로는 플라스틱 재활용 업체에서 분리 선별된 폴리에틸렌과 폴리프로필렌 그리고 이들을 혼합한 폐플라스틱을 각각 적용하였으며 $400\sim420^{\circ}C$의 분해 운전온도에서 폐플라스틱의 종류에 따른 시운전 평가를 하였다. 본 실증연구로부터 폴리에틸렌의 경우에 있어서는 79%의 재생유 회수율을 그리고 폴리프로필렌의 경우에 있어서는 80%의 재생유 회수율을 각각 얻을 수 있었으며 플라스틱 종류별 안정적인 운전조건을 확보할 수 있었다. 또한 폐플라스틱 투입량에 대한 설계용량과 운전용량과의 비교로부터 약 40$\sim$50%의 설계오차가 발생한 것으로 평가되었으며 이는 유화설비의 설계를 위하여 사용된 혼합폐플라스틱의 부정확한 물성 값에 기인한 것으로 판단된다. 따라서 본 연구로부터 얻은 시운전결과를 바탕으로 설계인자들을 확립하는 과정이 반드시 필요할 것으로 판단된다.

• Elastomers and Composites
• /
• v.40 no.2
• /
• pp.104-111
• /
• 2005

Virgin fluororubber(FKM) that is one of the highly-functionalized and expensive special rubber, and recycled FKM that is crushed by high temperature shear-crushing technique from recycled FKM were blended with the various mixing ratio to rubber blends. The cure characteristics and physical properties of these blended rubber compounds were investigated with various contents of recycled FKM and physical properties fur heat and fuels were also measured. Recycled FKM which is prepared by high temperature shear-crushing technique were blended to virgin FKM with the range of $0{\sim}50$ phr. The physical properties indicated that the rubber blend of recycled FKM with 30 phr turned out to be the best compound showing good dispersibility, heat resistance and fuel resistance and inexpensive in price.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.7
• /
• pp.1193-1203
• /
• 2000

In this study, in order to remove Cd(II) from aqueous solutions, strongly acidic cation exchange resin(SK1B) by Diaion Co. was employed as an adsorbent. Experiments were mainly performed in two parts at room temperature($25{\pm}5^{\circ}C$) : batch tests and adsorption kinetics tests. In batch tests adsorption equilibrium time, pH effects, temperature effects, several adsorption isotherms, and finally desorption tests were examined. In differential bed tests, an optimum flow rate and an overall adsorption rate were obtained. In the batch experiment, adsorption capability increased with pH and became constant above pH 6 and adsorption quantity increased with temperature. Batch experimental data found that Freundlich and Sips adsorption isotherms were more favorable than Langmuir adsorption isotherm over the range of concentration (5~15ppm). The desorbent used in the desorption test was hydrochloric acid solution with different concentrations(0.01~2N). The degree of regeneration increased with concentration of desorbent and decreased slightly with the number of regeneration. In the continuous flow process using a differential bed reactor, the optimum flow rate was $564m{\ell}/min$ above which the film diffusion resistance was minimized. The overall adsorption rate for the removal of Cd(II) by cation exchange resin was found as follows ; $r=1.3785C_{fc}^{1.2421}-2.0907{\times}10^{0.0746C_i}\;q_e^{0.0121C_i-0.0301}$

• Korean Journal of Microbiology
• /
• v.31 no.4
• /
• pp.318-325
• /
• 1993

The optima] conditions for the formation, the regeneration. and the spheroplast fusion of Flavimonas aryz/habitans spheroplasts were investigated. Cells were transformed to spherop]asts effectively by treatment of 0.5% volume (v/v) of 0.] M EDTA and ]00 flg/ml lysozyme at $37^{\circ}C$ for 30 min without shaking. Magnesium chloride and calcium chloride were effective on the stabilization of spheroplasts. and 20 mM calcium chloride in the rich regeneration medium improve the yield of regenerants as much as 3.5-fo]d. Addition of 0.8% bovine serium albumine (BSA) in dilution buffer for spheroplast formation improved the stabilization of spheroplasts over extended periods (4-6 hr) at room temperature. and thus increased the yield of recombinants to 4.5-fold. The spheroplast formation frequency and regeneration frequency of F aryzihabitans strain was 90.10% and 3.800/." respectively. The first regenerated cell of F. aryzihabitans spheroplasts were appeared 6 hours after plating. By I I hours after plating, 80% of spheroplasts were regenerated on thc rich regeneration medium containing 0.5 M sucrose. The intraspeci11c spheroplast fusion of F urvz/habitans was carried out and the properties of obtained fusants were investigated. Formation of fusion products was effective when the Flav/munas spheroplast mixture was treated with 40%(w/v) PEG6000 and 20 mM CaCl, for 10 min at room temperature. and thc formation of frequency of recombinants were $2.0{\times}10^{-5}~3.6{\times}10^{-5}$. All tested recombinant clones were very stable on further propagation.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.12
• /
• pp.2115-2123
• /
• 2000

This research was designed to investigate the mathematical model and kinetics of phenol desorption from spent activated carbon. elucidating the desorption characteristics of phenol in the case of using acetone. The Freundlich isotherm constant ($k_e$) is expressed as a function of temperature: $k_e(T)=0.1exp(797.297/T)$. The Freundlich isotherm constant(n) is a weak temperature function and is rarely affected by temperature below $50^{\circ}C$. whereas it is necessary to correct the n value with respect to temperature above $100^{\circ}C$ owing to significant deviation (~5%). Based on the assumption that the surface desorption reaction of phenol is rate limiting, the desorption model was developed. Desorption reaction constant($k_d$) was determined by means of fitting the theoretical results best to experimental ones. The Arrhenius relationships for $k_d$ was expressed by: $k_d(sec^{-1})=0.0479{\cdot}exp(-3037/T)$. The model was verified by comparing the experimental ones under different reaction conditions with the theoretical results determined by the previously estimated $k_d$. Since the difference between them is with 5%, it is expected that the desorption model of this research seems to be appropriate to explain the desorption of phenol from activated carbon by acetone. According to studies of the model. regeneration time and ratio was estimated as a function of temperature under present conditions as follows: (1) regeneration time : ${\tau}_{reg}(hr)=-0.08130T_c+8.4775$. (2) regeneration ratio : ${\eta}(%)=0.2210T_c+83.745$. The regeneration time at 15, 55, and $100^{\circ}C$. respectively. was 7, 4.2, and 0.35 hours, whereas the regeneration ratio was 87. 96. and 99%. respectively. Also. studies of the model would make it possible to determine the regeneration time and ratio under other specific conditions (temperature, applied acetone volume, amount of activated carbon, and initially adsorbed phenol amount).

• Korean Journal of Microbiology
• /
• v.24 no.3
• /
• pp.243-250
• /
• 1986

Protoplast formation and regeneration from wild-type and auxotrophic mutants of Candida pseudotropicalis CBS 607 as well as fusion between complementary mutants were carried out. Frequencies of protoplast formation from wild-type and histidine or adenine requiring mutants ranged from 96 to 100% whereas those from methionine or tryptophan auxotrophs were 52 and 72%, respectively. When bovine serum albumin(4mg/ml, BSA) was added to protoplasting buffer for cells of methionine or tryptophan auxotrophs grown in a medium supplemented with myoinositol(0.5mg/ml), 96-99 % of cells were converted to protoplasts. Protoplasts were regenerated at the frequencies ranging from 18 to 20%. However, the addition of BSA to protoplasting buffer and the supplement of myoinositol to a medium of cell growth doubled the regeneration rate except adenine auxotroph in which such an improvement was not observed. It was found that optimal concentrations of polyethylene glycol and $CaCl_2$ are 20% and 100mM while optimal pH and exposure time are 6.0 and 30min. The fusion frequencies between complementary mutants ranged from $1.5{\times}10^{-3}\;to\;8.8{\times}10^{-3}$ and were enhanced by the improvement in the rate of protoplast regeneration. When histidine auxotroph was fused with tryptophan mutant, several fusion products were obtained which were found to be in the state of aneuploid or diploid, judging from DNA content and the presence of a large nucleus in the products.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.67.1-67.1
• /
• 2010

Triple junction solar cell을 위한 a-SiGe middle cell의 조건별 광학적 특성에 관한 연구를 실시하였다. a-SiGe I층은 GeH4 유량, 압력, H2 dilution ratio를 변화시켜 제조하였으며 전기적, 광학적 특성을 비교하여 최종적으로 선택된 조건을 triple junction solar cell에 적용하였다. a-SiGe I층은 Ge contents가 증가함에 따라 band gap은 감소하고 45% 이상의 조건에서는 700nm 전후 파장의 투과율이 감소하며, 압력이 감소함에 따라 band gap은 소폭 감소하나 700nm 전후 파장의 투과율은 증가하였다. 그리고 H2 ratio가 증가함에 따라 band gap은 소폭 감소하나 투과율에는 큰 변화가 없었다. 상기 결과를 바탕으로 최종적으로 선택된 조건에서 triple-junction solar cell을 제작하여 평가한 결과 초기 변환효율 9%의 결과를 얻었다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.115.2-115.2
• /
• 2011

실리콘 박막 태양전지는 기판의 표면형상에 따라 셀 내부에서 이동하는 빛의 광학적인 경로가 크게 증가하여 변환효율의 향상을 기대할 수 있다. 금속 기판은 다양한 표면형상으로 가공이 용이하고 강도와 인성이 우수하며 가격이 저렴하여 실리콘 박막 태양전지의 기판재로 활발한 연구가 진행되고 있다. 본 연구에서는 금속 기판의 표면형상이 반사특성에 미치는 영향을 알아보고자 하였다. 금속 기판재의 표면형상은 기계적 연마 방식을 응용하여 다양하게 제작하였다. 반사특성을 보기 위하여 UV-visible spectrometer를 사용하여 총 반사율과 산란 반사율을 측정하였고, 표면 형상에 따른 Fe-Ni 기판과 Ag 후면반사막의 반사 특성이 태양전지 셀 내부의 광포획의 증가에 어떠한 영향을 주는지 비교 분석하였다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.77.1-77.1
• /
• 2011

슬러리 기포탑 반응기는 열 및 물질 전달의 용이성, 낮은 운전비용 및 장치의 간단성의 장점을 가지고 있어서 Fischer-Tropsch 반응, bio-reaction 등에 많이 응용되고 있다. 특히, 반응물은 기체 상태로 반응기에 투입이 되는데, 이 기포입자의 상승하는 힘을 바탕으로 기상/액상/고상이 균일하게 혼합되게 된다. 많은 연구자들이 이러한 기포탑 반응기의 성능을 개선하고자, 다양한 반응기 디자인에 대하여 보고하고 있다. 특히 반응기 내부에 tray를 설치함으로써, 기포 포집율을 증진시기고 액상의 역류를 최소화시키는 연구가 활발히 진행되고 있다. 본 연구에서는, 다양한 기공크기를 갖는 tray를 활용함으로써 높이에 따른 기포 포집율의 변화 및 반응기 내에 기포 입자의 거동 특성에 대하여 살펴보았다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.598-601
• /
• 2007

셀룰로오스, 헤미셀룰로오스, 리그닌으로 구성된 목질계 바이오매스를 이용한 가스화의 경우 30%의 리그닌 성분이 열에 안정한 상태인 타르로 형성되면서 가스화 후단공정에서의 정제, 발전 등에 직접 사용하기 어려우며, 가스화 효율을 저하시키는 원인이 된다. 이의 문제 해결을 위하여 본 연구에서는 촉매를 이용한 수증기 개질 반응을 통하여 타르를 합성가스로 개질시킬 수 있는 방법을 모색하기 위하여 다양한 온도, 촉매, 스팀 주입량 및 촉매크기에 따른 전환율, 생성가스 특성을 알아보았다. 타르 대상 물질로는 타르 내 상당부분을 차지하고 있는 톨루엔을 이용하였다. 일반적으로 반응온도, 스팀 주입량이 증가할수록 수소 생성량이 증가하였으며, 지르코니아로 증진된 니켈 촉매의 경우 600$^{\cdot}C$ 에서도 100%의 높은 전환율을 보였다. 일반적인 가스화기에서 배출되는 타르의 농도보다 10배 높은 조건에서도 100%의 높은 전환율을 얻을 수 있었으며, 이를 통하여 실제 공정으로의 적용시에도 후단 공정의 부담을 줄일 수 있는 개질기로 적용 가능할 것으로 보인다.