• Transactions of the Korean Society of Mechanical Engineers
• /
• v.9 no.6
• /
• pp.732-742
• /
• 1985

Measurements of mean velocity and turbulence characteristics are obtained with a linearized constant temperature hot-wire anemometer in a two-dimensional turbulent jet discharging parallel to a flate. Wall static pressure distribution is also measure. The Reynolds number based on the jet nozzle width (D) is about 42,000 and the step height is 2.5D. The reattachment length is found to be 7.5D by using both wool tuft and oil methods. Upstream of the reattachment point, there exist double coherent structures and mean velocity, Reynolds stresses and triple product profiles are asymmetric about jet center line due to the influence of streamline curvature and recirculating flow region. Near the reattachment point, wall static pressure and turbulence quantities change its shape rapidly because of the large eddies by the solid wall. Especially, turbulence intensity has a maximum value in the reattachment regin, then decreases slowly in the redeveloping wall jet ragion. Downstream of X/D=14, a single large scale eddy structure is formed. Far downstream affer the reattachment(X/D.geq.18) mean velocity profile, the decay of maximum velocity and the variation of jet half width are nearly similar to those of plane wall jet, but the Reynolds stresses are higher than those of the latter.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.27 no.1
• /
• pp.145-152
• /
• 2021

The purpose of this study was to determine the optimal distances between pipes to minimize the pressure loss and turbulent intensity. This was accomplished by investigating the distances between sleeve-jointed pipes and the flow changes in pipes based on variations in the Reynolds (Re) number when installing adjusting pieces for the pipes. When the thickness tp of the sleeve-jointed piping was fixed at 5 mm and the pipe lengths Lp were 10, 50, 100, and 200 mm, the correlations with the velocity of the sleeve-jointed part, pressure distribution, length of the reattachment point in the recirculation area, and Re number were analyzed. The flow characteristic of the sleeve-jointed part from a laminar to a turbulent flow region was determined by setting the Re range to 200 ≤ Re ≤ 5,000. This was done by utilizing Ansys Fluent 18.1, which is a commercial program. The enlargement and contraction ratios of the sleeve-jointed part were 1.2 and 0.83, respectively, and the turbulent intensity of the sleeve downstream edge and pressure change both increased as the Re number increased while Lp remained constant. The fact that the flow on the sleeve wall surface was disturbed by tp resulted in losses in velocity energy. Therefore, the edge of the sleeve-jointed part was also effected. When Lp was 10 mm or less, the turbulent intensity of the edge part did not change significantly as the Re number increased. The reattachment point in the recirculation area did not appear at Lp of 10 mm or less and was not affected by the vortex. In the case of 3,000 ≤ Re, the reattachment length of the wall surface of the sleeve-jointed part was nearly constant as Lp increased.

• Solar Energy
• /
• v.10 no.1
• /
• pp.31-37
• /
• 1990

An experimental study for the flow in an axisymmetric cavity of rectangular tube was performed. The pressure and heat transfer coefficient along the side and opposite-walls of the cavity were measured. The cavity length was varied from 80mm to infinity during the experiment. As the result of this study, it was found that as the length of cavity increased beyond the reattachment point, the heat transfer coefficient decreased. It was also found that the mean heat transfer coefficient became maximum near the reattachment point.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.6
• /
• pp.512-519
• /
• 2013

It is important to understand the vibrating behavior of plate structures for its many engineering applications. In this study, the vibration characteristics of strip plates that have finite width and infinite length are investigated theoretically and numerically. The waveguide finite element(WFE) approach, which is an effective tool for studying waveguide structures, is used in this study. The WFE method requires only a cross-sectional finite element model, and uses theoretical harmonic solutions to assess wave propagation along the longitudinal direction. First, WFE results for a simple strip plate are compared with the theoretical results(i.e., dispersion diagrams and point mobilities) to validate the numerical model. Then, in the numerical analysis, different numbers of longitudinal stiffeners are included in the plate model to investigate the effects of stiffeners in terms of the dispersion curves and mobilities. Finally, the dispersion curves of a stiffened double plate are obtained to examine the characteristics of its wave propagation.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2000.04a
• /
• pp.32-32
• /
• 2000

잠입노즐은 로케트 추진기관의 길이 및 중량을 감소시켜 체계설계의 관점에서 볼 때 많은 이점을 제공한다. 본 연구에서는 3단형 과학로케트 원지점 차넣기 모타(apogee kick motor)에 적용하기위한 잠입노즐의 기초기술 개발에 주안점을 두었다. 고고도에서 저속으로 회전하며 비행하는 원지점 차넣기 모타를 제작하기위해서 체계 요구성능에 의해 예상된 실물형의 50% 크기에 해당하는 축소형 잠입노즐을 제작하였다. 잠입노즐은 잠입부의 내외부가 고온의 추진제 연소가스에 노출된 상태에서 노즐 내부 압력 외에 연소실압에 의한 외부압력이 작용하므로 이를 고려한 열 및 구조설계가 중요하다. 본 연구에서는 노즐 수렴부와 목부에 일체형 그라파이트 소재를 적용하고 확장부 내열재 및 잠입부 배면내열재에 탄소/페놀 복합재를 노즐 내열재로 사용하였다. 그리고 이들의 구조적 지지를 위해 스틸구조물을 적용하였다. 적용된 스틸구조물에는 K형 열전쌍을 이용해 내열재와 구조물 온도를 측정할 수 있는 관통구멍 및 나사부를 구조물 외변에 가공하였다. 열전쌍은 노즐 목직경의 2, 4배 되는 확장부 내열재 단면위치의 2mm와 4mm 깊이와 구조물 내면 및 외면의 4개소에 열전쌍을 부착하여 지상연소시험시 노즐 내열재와 구조물의 온도분포를 관찰한다. 그리고 노즐 조립시 확장부 내열재와 구조물에 각 각 반원형 홈을 내어 여분의 접착제가 원형 홈에 밀려들어가 경화되어 노즐 기밀유지와 체결력을 향상시킬 수 있는 원형공간 접착제 충전 공법을 적용하여 실제모타에 대한 적용가능성을 지상연소시험을 통해 확인한다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.5
• /
• pp.1253-1261
• /
• 1993

Numerical analysis and measurements of the velocity and temperature distributions in buoyancy assisting laminar mixed convection flow over a vertically located, two-dimensional backward-facing step are reported. Laser-Doppler Velocimeter and Constant Temperature Anemometer operated in constant current were used to measure simultaneously the velocity and temperature distributions in the recirculation region downstream of the step. The reattachment length was measured by using flow visualization technique for different inlet velocities, wall temperatures and step heights. While the reattachment length $X_r$ increases as the inlet velocity or step height increase, it decreases as the buoyancy force increases, causing the size of the recirculation region to decrease. For the experimental range of $Gr_s$/$Re_{s}^{2}$$\times$$10^3$<17, a correlation equation for the reattachment length can be given by $X_{r}=1.05(2.13+0.021 Re_{s})exp$ $(-33.7_s^{-0.186}/Gr_{s}/Re_{s}^2).$ The Nusselt number is found to increase and the location of its maximum value moves closer to the step as the buoyancy force increases. The location of the maximum Nusselt number occurs downstream of the reattachment point, and distance between the reattachment point and the location of the maximum Nusselt mumber increases as the buoyancy force increases. Computational prediction agrees favorably well with measured results.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.6
• /
• pp.1269-1281
• /
• 1989

본 연구에서는 H를 고정하고 L을 변화시켜가며 내부의 유동구조가 어떻게 변하는가를 살펴보고, 특히 재부착이 일어나는 경우에는 급확대 부분만 존재하는 기존 실험결과와 비교분석하여 하류의 급축소부분이 전체 유동구조에 어떤 영향을 미치는가를 살펴보고자 한다. 실험에서 사용된 작동유체는 공기이며, 입구관 직경은 110mm, 급확대점과 급축소점사이의 연결부 직경은 220mm, 연결부의 길이는 L=300, 600 그리고 900mm의 3가지를 선택하였으며 기준속도는 입구관의 중심속도로 9.71 m/s이다. 입구직경(110mm)을 기준으로 한 Reynolds 수는 $R_{e}$=73,000 이고 입구관반경과 연결부반경의 차이인 계단높이(H=55mm)를 기준으로 하면 $R_{e=36}$ ,500이다. 연결부 의 급확대부분에서 입구관반경을 기준으로 한 반경확대비는 2이고 급축소부분의 반경 축소비는 1/2이다. 측정항목은 유동방향의 벽면압력분포, 유동방향의 평균속도분포 및 난류강도 등이며, L=900mm인 경우는 반경방향과 원주방향의 난류강도, Reynolds 전단응력도 측정되었다.

• Korean Journal of Heritage: History & Science
• /
• v.45 no.4
• /
• pp.54-73
• /
• 2012

In this article, we examined the patterns of activities of the Sarmathians though in a humble measure, with a focus on the regions where the Sarmathian sheaths spreaded. One of the main weapons the mounted nomads like the Scythias, the Sarmathians, and the Alans used at war was a spear. Though complementary, a sword was the most convenient and appropriate weapon when fighting at a near distance, fallen from the horse to the ground. The Sarmathian swords continued the tradition of the Akinakes which the Scythias or the Persians used, but those of the Sarmathians showed some advances in terms of the easiness with which a sword was drawn out from a sheath, and the way the sheaths were worn to parts of a human body. It turns out that the Sarmathian sheaths, which were designed for the people to draw swords easily, having the sheaths attached to thighs through 4 bumps, spread extensively from Pazyryk, Altai, to South Siberia, Bactria, Parthia and Rome. The most noteworthy out of all the Sarmathian sheaths were the ones that were excavated from the 4th tomb in Tillatepe, Afghanistan which belonged to the region of Bactria. The owner of the fourth tomb of Tilla-tepe whose region was under the control of Kushan Dynasty at that time, was buried wearing Sarmathian swords, and regarded as a big shot in the region of Bactria which was also under the governance of Kushan Dynasty. The fact that the owner of the tomb wore two swords suggests that there had been active exchange between Bactria and Sarmathia. It seemed that the reason why the Sarmathians could play an important role in the exchange between the East and the West might have something to do with their role of supplying Chinese goods to Silk Road. That's why we are interested in how the copper mirrors of Han Dynasty, decoration beads like melon-type beads, crystal beads and goldring articulated beads, and the artifacts of South China which produced silks were excavated in the northern steppe route where the Sarmathians actively worked. Our study have established that the eye beads discovered in Sarmathian tomb estimated to have been built around the 1st century B.C. were reprocessed in China, and then imported to Sarmathia again. We should note the Huns as a medium between the Sarmathians and the South China which were far apart from each other. Thus gold-ring articulated beads which were spread out mainly across the South China has been discovered in the Huns' remains. On the other hand, between 2nd century B.C. and 2nd century A.D. which were main periods of the Sarmathians, it was considered that the traffic route connecting the steppe route and the South China might be West-South silk road which started from Yunnan, passed through Myanmar, Pakistan, and Afghanistan, and then went into the east of India. The West-south Silk road is presumed to have been used by nomadic tribes who wanted to get the goods from South China before the Oasis route was activated by the Han Dynasty's policy of managing the countries bordering on Western China.