• Journal of the Korean GEO-environmental Society
• /
• v.12 no.12
• /
• pp.71-78
• /
• 2011

This paper aims to present the evaluation of engineering characteristics and reusing possibility of waste powders produced in dolomite and limestone nonmetal mining by physical and mechanical experiments on compaction, uniaxial compressive strength, permeability, chemical composition, and so on. Granite soil, 2 types of limestone waste powder, and 1 type of dolomite waste powder were used for main materials, and cement and bentonite were used for admixed materials in this experiments. The findings based on the experimental results are the severe difference of chemical composition of the dolomite & limestone waste powder and the crushed rock waste powder, and the outstanding of engineering characteristics of the dolomite waste powder with high content of MgO compared with the limestone waste powder. The engineering properties on compaction, uniaxial compressive strength, and permeability are enhanced with increase of admixed ratio of waste powder on granite soil. From the experimental results, it can be suggested that the dolomite waste powder admixed with in-situ granite soil is useful as geo-materials with considering of distribution costs.

• Journal of the Korean Geotechnical Society
• /
• v.17 no.6
• /
• pp.207-213
• /
• 2001

Shaking table tests to investigate the dynamic friction behavior of interfaces between dense dry granular soils and construction material(concrete) were performed and the results are reported. The results show the variation of dynamic interface friction coefficients between dense dry granular soils and construction material was small in the sliding velocity range employed in this study. It was also observed that dynamic interface friction coefficients decreased as mean grain sizes of granular soils increased. These coefficients were compared with the friction coefficients obtained from the peak internal friction angles of the same granular soils by plane strain compression tests.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2010.05a
• /
• pp.401-402
• /
• 2010

This research initially suggest flexural toughness density as a key parameter describing energy absorption capacity of High Performance Fiber Reinforced Cementitious Composites [HPFRCC] regardless of the size of specimen. Two types of high strength steel fibers, Hooked and Twisted fiber, were used in two types of flexural specimen ($100{\times}100{\times}350mm^3$ and $150{\times}150{\times}500mm^3$) to estimate and validate the flexural toughness density.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2009.05a
• /
• pp.213-213
• /
• 2009

선박 건조시에 사용되는 알루미늄 합금은 환경친화적인 재료로 각광을 받고 있으며, FRP 선박의 대체재료로 부각되고 있다. 선박 운항시 해수 환경하에서 선체의 부식을 방지하기 위해 도장 뿐만아니라 희생양극이나, 음극방식 등은 필수불가결한 사항이다. Al-Mg 합금인 5083-H116에 대한 천연 해수 용액에서 저변형율 인장시험을 통한 응력부식균율이나 수소취화의 영향이 없는 최적의 방식 전위를 결정하였다.

• Proceedings of the KAIS Fall Conference
• /
• 2006.11a
• /
• pp.147-149
• /
• 2006

본 연구는 산업용과 의료용에 사용되는 비파괴 검사용 X 선 영상시스템에 이용되는 X 선을 직접 감지하는 방식의 센서를 실리콘 반도체 재료를 사용하여 개발하는데 목적이 있다. 현재 사용되고 있는 비파괴 시험 용 검사 방법은 X-선을 사용하고 감지 필름 또는 고가의 감지재료를 사용하고 있으나 본 과제에서는 경제성이 있으며 기술기반이 확고한 실리콘 재료를 사용하고 디지털 촬영 방식을 도입하여 컴퓨터로 시험결과를 영상 처리한다는 장점이 있으며 영상 자료의 컴퓨터 베이스 처리와 영상 저장이 편리하게 이루어졌다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.10
• /
• pp.2089-2095
• /
• 2002

Ceramic/metal composites have many attractive properties and great potential fur applications. Interfacial fracture properties of different layered composites are important in material integrity. Therefore, evaluation of fracture toughness at interface is required in essence. In this study, the mechanical characteristics for interface of ceramic/metal composites were investigated by indentation test of micro-hardness method. Apparent interfacial toughness of TBC system could be determined with a relation between the applied load and the length of the crack formed at the interface by indentation test.

• International Journal of Highway Engineering
• /
• v.5 no.3 s.17
• /
• pp.31-42
• /
• 2003

The KHC Test Road project was initiated on 1991 to develop Korean Pavement Design Guide. It was constructed along the Joongbu Inland Expressway line between Yeoju and Gamgok. It is two-lane wide expressway containing fifteen asphalt and twenty-five Portland cement concrete test pavement sections. Various sensors were installed in the Test Road to evaluate the behavior of test pavement sections under the influence of traffic load and environmental change. The most important issues in the sensor installation are the accurate location and long-term survivability. They are directly influenced by the sensor installation methodology. The methodology for asphalt strain gages is mainly discussed in this paper because it is the second important sensors in the KHC Test Road project. In order to find the best methodology, we evaluated existing methodology from prior experience and several conducted test installations. We have tried mound, block out, and trench cuts since 2000. Among three methods, block out was the most effective one in terms of accurate location, long-term survivability, and material homogeneity. However, this method cannot be applied to the wearing coarse so that the mound method was used as an alternative. The block out method was applied to base and intermediate layers while the mound method was used to the wearing coarse. Three hundred seventy-four asphalt strain gauges were installed on asphalt pavement sections from September 3rd to November 18th in 2002. According to the sensor measurement evaluation, 6.3% of sensor demonstrated over ranged readings for mound method installation and 2.5% did for block out method installation. We lost only two sensors during the installation. It is 99.5% survival and it is excellent survival rate according to other experience.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.25 no.6
• /
• pp.193-198
• /
• 2021

In this study, the rheological characteristics and of 3D printing composite materials and the compressive strength characteristics according to the lamination patterns were evaluated. As a result of rheology test, rapid material change was observed after 60 minutes of extrusion, yielding stress 1.4 times higher than immediately after mixing, and plastic viscosity was 14.94-25.62% lower. The compressive strength of the specimens manufactured in the mold and the laminated specimens were compared, and the lamination pattern of the laminated specimens were 0°, 45°, and 90° as variables. The compressive strength of the mold casting specimen and the laminated specimen from 1 to 28 days of age showed similar performance regardless of the lamination pattern. In particular, at the age of 28 days, the modulus of elasticity, maximum compressive strength, and strain at maximum stress of all specimens were almost the same. In order to analyze the interface of the laminated specimens, X-ray CT analysis of the specimen whose compressive strength were measured was performed. Through CT analysis, it was confirmed that cracks did not occur at the lamination interface, which can be judged that the interface in the laminated specimen behaved in an integrated manner.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.21 no.6
• /
• pp.634-641
• /
• 2001

Shape memory alloy has been used to improve the tensile strength of composite by the occurrence of compressive residual stress in matrix using its shape memory effect. In order to fabricate shape memory alloy composite, TiNi alloy and A16061 were used as reinforcing material and mix, respectively. In this study, TiNi/A16061 shape memory alloy composite was made by using hot press method. However, the specimen fabricated by this method had the bonding problem at the boundary between TiNi fiber and Al matrix when the load was applied to it. A cold rolling was imposed to the specimen to improve the bonding effect. It was found that tensile strength of specimen subjected to cold rolling was more increased than that of specimen which did not underwent cold rolling. In addition, acoustic emission technique was used to quantify the microscopic damage behavior of cold rolled TiNi/A16061 shape memory alloy composite at high temperature.

• Composites Research
• /
• v.30 no.3
• /
• pp.223-228
• /
• 2017

The article explains about development of flame retardant self-reinforced composites (FR-SRC) through compression molding technique by utilizing Polypropylene (PP), Ammonium polyphosphate (APP) and chitosan. The effect of APP and chitosan on mechanical, thermal and flame retardant properties in FR-SRC were studied. The mechanical strength of FR-SRC is enhanced than Pure SRC. However, the strength is decreased significantly with increasing the concentration of both flame retardant fillers. But comparison, chitosan filled FR-SRC is stronger than APP filled FR-SRC. In case of flame retardancy, APP is more effective than chitosan. These results can be applicable to provide light weight and recyclable flame retardant self-reinforced composites for automobile and packaging industries, etc.