• Bulletin of the Korean Space Science Society
• /
• 2010.04a
• /
• pp.31.3-31.3
• /
• 2010

인공위성은 궤도상에서 별추적기를 기준으로 자세제어를 수행한다. 이러한 별추적기의 지향방향 정밀도는 위성의 운용 및 관측성능에 커다란 영향을 미치게 된다. 따라서 별추적기의 지향방향은 초기에 설정된 지향방향으로부터 변화하지 않는 것이 중요하다. 일반적으로 별추적기는 가시영역을 확보하기 위하여 특정한 방향으로 장착되어야 하고 이를 위하여 위성 구조물과 연결시켜 주는 장착 구조물이 적용된다. 이러한 장착 구조물에는 히터가 부착되어 온도 제어를 함으로써 별추적기의 지향오차를 최소화 하도록 한다. 이 논문에서는 온도제어를 위해 히터가 작동하여 장착구조물에 온도구배가 발생할 경우 별추적기의 지향방향의 변화가 허용 가능한 수준이내에 해당하는가를 해석적으로 검토한 결과를 기술한다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2002.04a
• /
• pp.4-5
• /
• 2002

로켓 엔진의 개발에 있어 성능과 수명(life time)에 가장 문제가 되는 것은 연소 안정성에 있다. 일반적으로 연소 불안정을 야기시키는 것은 3가지로서 축방향(longitudinal), 반경방향(radial)과 접선방향(longitudinal) 모드(mode)가 있다. 이와 같은 모드를 제어하는 방법에는 수동적 제어방법으로 음향공(acoustic cavity)과 배플(baffle)이 있으며, 음향공은 모드에 관계없이 특정한 주파수에 맞추어 체적을 조절하여 음향파(acoustic wave)를 감쇄시키는 것이고 배플은 주파수에 관계없이 접선방향 모드를 제어하는 것이 기본 목적이나 허브(hub)를 설치하여 반경방향 모드까지 제어할 수 있다. 음향공은 엔진의 성능 또는 연소장에는 영향을 주지 않고 작동하는 반면, 배플은 초기 엔진설계를 할 때 고려하지 않으면 후에 배플을 장착하였을 때는 초기 설계의 제한 때문에 장착의 어려움과 성능 및 연소장에 영향을 미쳐 원하지 않는 엔진의 시험 결과를 야기할 수 있다. 본 연구에서는 KSR-III와 동일한 조건의 연소기에서 다양한 배플을 장착하였을 경우에 대하여 성능과 연소장에 대하여 예측하였다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.11a
• /
• pp.17-20
• /
• 2007

Effect of radial position of half-wave resonator is investigated experimentally for acoustic damping of tangential mode in a combustion chamber by adopting acoustic cold test. When resonator with optimal tuning length is installed， damping is enhanced as its radial location is away from the center of the faceplate. And, radial profile of damping factor is similar to that of the amplitude of the acoustic mode to be damped. As the location is close to the center, acoustic damping is mitigated and independent on the resonator length. on the other hand， the resonator with non-optimal length dose not show any effect of its radial position.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.14 no.2
• /
• pp.127-134
• /
• 2014

This paper presents a study on the radiation characteristics of low-VHF band electrically small antenna for direction finding. Firstly, it is simulated the antenna for mounting on flat ground and tank model(in 40MHz), and measured for mounting 1/10 scaled model(in 400 MHz). In case of flat ground feed at ${\phi}=0^{\circ}$, $180^{\circ}$(xz-plane), yz-plane $E_{\phi}$ (H-plane) and xz-plane $E_{\theta}$ (E-plane) radiation patterns are hemispheric omni-direction due to effect of narrow ground side. Then, in case of tank model, it is shown equally in case of the flat ground, yz-plane $E_{\phi}$ (H-plane) and xz-plane $E_{\theta}$ (E-plane) radiation patterns are hemispheric omni-direction nearly without effect of mounting position. Therefore, the suggested electrically small antenna for direction finding, in case of mounting on ground narrow side xz-plane(E-plane), is shown more stable radiation patterns as direction finding antenna.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.12 no.2
• /
• pp.1-7
• /
• 2008

Effect of radial position of half-wave resonator is investigated experimentally for acoustic damping in a combustion chamber by adopting acoustic cold test. Acoustic damping is quantified by damping factor. When resonator with optimal tuning length is installed, damping is enhanced as its radial location is away from the center of the faceplate. And, spatial profile of damping factor is similar to that of the amplitude of the acoustic mode to be damped. As the location is close to the center, acoustic damping is mitigated and independent of the resonator length. On the other hand, the resonator with non-optimal length dose not show any effects of its radial position. Acoustic-damping capacity can be evaluated as functions of resonator length and position.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.18 no.5
• /
• pp.89-95
• /
• 2018

In this paper, we analyze the antenna performance changes caused by the aircraft structure, diffraction and reflection, when the direction finding antenna used in the aircraft is mounted on the aircraft. Direction finding antenna is an antenna that receives radar threat signal in the direction finding device of aircraft electronic warfare system. Recently, because various antenna are mounted on an aircraft, various analyzes such as antenna performance and interference analysis are required. Therefore, the electromagnetic analysis was carried out by installing a broadband direction finding antenna with 50% bandwidth on simulated aircraft, and the direction finding performance was analyzed by comparing the single antenna performance with the performance mounted on the aircraft. The analyzed direction finding accuracy was $6.47^{\circ}$ RMS and predicted to be suitable as an antenna for aircraft direction finding antenna.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.265-270
• /
• 2010

This paper presents the rocket motor support structure to position solid rocket engine within a missile fuselage. When the rocket motor is mounted inside a missile fuselage, fuselage structure must be designed to withstand various structural problems resulting from inserted rocket motor such as axial thrust force, shock/vibration, axial deformation of the rocket motor tank in addition to the flight loads. The motor support structure system proposed in this paper proved to be very simple and efficient while satisfying all the design requirements.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2000.04a
• /
• pp.15-15
• /
• 2000

제트 베인에 의한 추력 방향 제어 장치는 롤 운동 제어를 가능하게 하고, 큰 선회 각도를 얻을 수 있는 장점이 있으나, 기계 장치가 비교적 복잡하고, 제트 베인의 열적, 구조적 문제를 해결하여야 한다. 복잡한 기계 장치는 유동 해석의 측면에서 고려해 볼 때 격자 형성을 어렵게 만들어 유동장 해석을 통한 성능예측을 어렵게 만든다. 구조물의 응력해석을 위하여 제트 베인 표면에서의 정압력과 더불어 마찰력도 고려하여야 하는데, 정확한 마찰력 계산을 위해서는 난류 모델링이 필수적이고, 그에 따라 벽면 근처에서 격자를 밀접시키는 것이 요구된다. 본 연구에서는 상용 유동해석 소프트웨어인 Fluent를 사용하여 제트 베인이 장착된 추력 방향 제어 장치의 3차원 난류 유동장 계산을 수행하였다. 피치, 요 운동의 경우와 롤 운동의 경우로 구분하여 계산하였으며, 최대 받음각을 $25^{\cire}$ 로 하여 제트 베인의 받음각에 따라 회전축에 작용하는 힘과 모멘트를 계산하였다. 본 연구의 결과는 향후 개발될 제트 베인이 장착된 추력 방향 제어 장치의 개념설계 단계에 필요한 기본자료로서 신뢰도를 높이는데 도움이 되리라 판단된다.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.3
• /
• pp.218-225
• /
• 2013

Vertically-launched missiles are supported as erected vertically in the vertical launching system of warship, and they should be mounted in the same way when vibration-tested. However, mounting missiles vertically makes a fixture, which is a supporting structure, bulky and heavy so requiring a high-performance exciter. Mounting missiles as laid down horizontally in a vibration test is economical regarding fixture manufacturing and exciter performance, but it makes test results incorrect because the different mounting direction has effects on the test results. A bending moment due to missiles' weight happens to missiles, and resilient mounts, which support missiles in the vertical launch system, deflect differently from the real situation because of the static deflection of these mounts due to missiles' weight. If the resilient mounts supporting missiles have nonlinear force-deflection characteristics, vibration test results become more different from the true results. This paper proposes to support missiles with an additional resilient mount such as a bunge code in order to solve those problems coming from mounting vertically-launched missiles as laid down horizontally in vibration tests. The proposed approach enables to obtain the same test results as in their actual mounting condition even though vertically-launched missiles are mounted in a different direction.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.24 no.4
• /
• pp.529-535
• /
• 2020

It is important to secure the driver's external field view in armored vehicles surrounded by iron armor for preparation for the enemy's firepower. For this purpose, a 360 degree rotatable surveillance camera is mounted on the vehicle. In this case, the key idea is to recognize the head of the driver wearing a helmet so that the external camera rotated in exactly the same direction. In this paper, we introduce a method that uses a MEMS-based AHRS sensor and a illuminance sensor to compensate for the disadvantages of the existing optical method and implements it with low cost. The key idea is to set the direction of the camera by using the difference between the Euler angles detected by two sensors mounted on the camera and the helmet, and to adjust the direction with illuminance sensor from time to time to remove the drift error of sensors. The implemented prototype will show the camera's direction matches exactly in driver's one.