• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.5
• /
• pp.1-1
• /
• 2001

비휘발성 메모리 소자로의 응용의 관점에서, sol-gel 방법으로 La 을 10mo1% 로 고정시킨 PLZT (10/y/z) 박막을 제작하여 Zr/Ti 조성비에 따른 구조적 및 전기적 특성을 조사하였다. PLZT(10/40/60) 박막은 로제트와 파이로클로르 상이 관찰되었으며, Zr/Ti 조성비에서 Ti 함유량이 증가함에 따라, (100) 배향성, 결정립 크기와 표면 거칠기는 증가되었다. 또한 Zr/Ti 조성비에서 Ti 함유량이 증가함에 따라, 10㎑ 에서 비유전율은 600 에서 400 으로 감소된 반면, 유전손실은 0.028 에서 0.053 로 증가되었으며, 170 ㎸/cm 에서 누설전류밀도는 1.64×$10^{-6}$ 에서 1.26×$10^{-7}$A/㎠ 으로 감소되었다. 그리고 ± 170㎸/㎝ 에서 측정한 PLZT 박막의 이력곡선을 측정한 결과, Zr/Ti 조성비가 40/60 에서 0/100 로 변화함에 따라 PLZT 박막의 잔류분극과 항전계는 6.62 에서 12.86 μC/cm2, 32.15 에서 56.45㎸/㎝ 로 각각 증가되었으며, 피로와 retention 특성 역시 개선되었다. PLZT 박막에 ±5V 의 사각펄스를 $10^9$ 회 인가하여 피로특성을 측정한 결과, PLZT(10/40/60) 박막의 잔류분극은 초기분극값으로부터 50% 감소된 반면, PLZT(10/0/100) 박막은 30% 감소되었다. 또, $10^5$ 초의 retention 결과에서 PLZT(10/0/100) 박막은 초기분극값에서 오직 11% 만이 감소된 반면, PLZT(10/40/60) 박막은 40% 감소되었다.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.19 no.4 s.74
• /
• pp.347-356
• /
• 2006

In this paper, practical nonlinear inelastic analysis method of 3-dimensional steel structures accounting for gradual yielding with fibers on a section is developed. Geometric nonlinearities of member(p-$\delta$) and frame(p-$\Delta$) are accounted for by using stability functions. Residual stresses are considered by assigning initial stresses to the fiber on the section. The elastic core in a section is investigated at every loading step to determine the axial and bending stiffness reduction. The strain reversal effect is captured by investigating the stress change of each fiber. The proposed analysis proves to be useful in applying for practical analysis and design of three-dimensional steel frames.

• Journal of the Society of Naval Architects of Korea
• /
• v.52 no.3
• /
• pp.248-254
• /
• 2015

The strength and fatigue life of Satin and Twill-woven CF/epoxy composite(CFRP) have been investigated. Damage mechanism fatigue method has been used to assess fatigue damage accumulation. It is based on measured residual stiffness and residual strength of carbon-fiber reinforced plastic(CFRP) laminates under cyclic loading. Fatigue damage evolution in composite laminates and predict fatigue life of the laminates were simulated by finite element analysis(FEA) method. The stress analysis was carried out in MSC patran/Nastran. A modified Hashin's failure criterion di rmfjapplied to predict the failure of the experimental data of fatigue life but a Ye-delamination criterion was ignored because of 2D modeling. Almost linear stiffness and strength degradation were observed during most of the fatigue process. These stress distribution data were adopted in the simulation to simulate fatigue behavior and estimate life of the laminates. From the results, the predicted fatigue life is more conservatively estimated than the experimental results.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.19 no.2
• /
• pp.130-139
• /
• 2023

This paper examines the quantification of uncertainty for welding residual stresses in dissimilar metal welds used in nuclear power plants. A mock-up of a dissimilar metal weld pipe, consisting of carbon and stainless steel pipes, was fabricated to measure the residual stress. A Round-Robin analysis was conducted by Korean institutions to assess the welding residual stress. The analysis was carried out in the second order, and the data obtained by each institution was evaluated based on the information provided. Using the Round-Robin results, the distribution of uncertainty in welding residual stresses among Korean institutions was evaluated. The quantification of uncertainty for Korean institutions was found to have a wider range compared to the distribution of welding residual stresses observed in overseas institutions. This study is considered useful in the establishment of comprehensive strategies for evaluating welding residual stress analysis methods used by domestic institutions.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1371-1375
• /
• 2005

The paper has analyzed the influence of tire design variable on the tire Force and Moment (F&M) characteristics, especially by the belt angle, the Plysteer Residual Aligning Torque (PRAT) which is considered as one of the causing factors for the vehicle pull. To validate the tire FE model, the tire stiffness and the PRAT which can be derived from the simulation data have been compared with the experimental data of test machine. In addition to PRAT characteristic, the tire stiffness and cornering characteristics due to the belt angle have been investigated. The effects of drum's curvature on the PRAT have been also investigated using the tire FE model and the usefulness of the current drum type F&M test machine can be confirmed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.12
• /
• pp.6521-6526
• /
• 2013

Elastic and nonlinear ultimate strength analyses were conducted to examine the effects of the stiffness and slenderness of flat-type stiffeners on ultimate in-plane strengths of a stiffened plate system. Although it is not feasible to consider local buckling in the stiffeners in elastic analysis, it was confirmed that the in-plane strengths of the stiffened plate system can be achieved by antisymmetric buckling mode when a certain level of stiffness in the stiffeners is provided. Nonlinear ultimate strength analysis, in which initial imperfection and residual stress are incorporated, showed that the ultimate strengths are sensitively affected by the mode shapes for initial imperfections. The slenderness limit for flat-type stiffeners in KHBDC (Korean Highway Bridge Design Code) was evaluated as conservative compared to the analysis results.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.2 s.179
• /
• pp.104-112
• /
• 2006

The influence of tire belt angle on the Plysteer Residual Aligning Torque(PRAT) and the cornering stiffness by the FEM has been studied. The PRAT is a performance factor of the tire about vehicle pull, and the cornering stiffness has relation to vehicle steering response of outdoor test. To validate FE model for analysis, simulation data for both the static stiffness(vertical, lateral) and the PRAT have been compared with the experimental data. In addition to the characteristics of the PRAT and the cornering stiffness due to the tire belt angle, rolling and cornering contact characteristics have been studied. The tendency of the PRAT and the cornering stiffness due to the belt angle can be used as a guide line for the tire design in relation to vehicle pull and vehicle steering response.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.10 s.181
• /
• pp.2552-2559
• /
• 2000

Most of ferrous b.c.c weld materials have martensitic transformation during rapid cooling after welding. It is well known that volume expansion due to the phase transformation could influence on the relaxation of welding residual stress. To apply this effect practically, it is necessary to establish a numerical model which is able to estimate the effect of phase transformation on residual stress relaxation quantitatively. For this purpose, the analysis is carried out in two regions, i.e., heating and cooling, because the variation of material properties following a phase transformation in cooling is different in comparison with the case in heating, even at the same temperature. The variation of material properties following phase transformation is considered by the adjustment of specific heat and thermal expansion coefficient, and the distribution of residual stress in analysis is compared with that of experiment by previous study. In this study, simplified numerical procedures considering phase transformation, which based on a commercial finite element package was established through comparing with the experimental data of residual stress distribution by other researcher. To consider the phase transformation effect on residual stress relaxation, the transition of mechanical and thermal property such as thermal expansion coefficient and specific heat capacity was found by try and error method in this analysis. In addition to, since the transformation temperature changes by the kind and control of alloying elements, the steel with many kinds of transformation temperature were selected and the effect of transformation on stress releasement was investigated by the numerical procedures considering phase transformation.

• The Korean Journal of Pesticide Science
• /
• v.14 no.3
• /
• pp.209-218
• /
• 2010

There experiment were carried out to analyze for pesticide residues in 4 kinds of dried fruits collected in northern area of Seoul in 2007~2009. Total of 213 samples were analyzed. According to the results, 20 kinds of residual pesticides were detected. Residual pesticides were detected in 66 samples (31.0%) and 8 samples (3.8%) exceeded maximum residue limits (MRL). Cypermethrin, fenvalerate, endosulfan, chlorpyrifos, bifenthrin were detected frequently. The Pesticide types which were detected in dried furits were revealed in order of pyrethroid > organophosphate > organochloride > dicarboximide. Detection rates of dried fruits were dried chinese matrimony vein (53.0%), dried jujube (34.9%), dried rubi fructus (7.6%) and dried maximowiczia chinensis (4.6%). Based on these results, we investigated the risk assessment from amount of residual pesticide in dried jujube. Range of %ADI were 0.0001~0.0081%, but the value has not effected on human health.

• Korean Journal of Food Science and Technology
• /
• v.47 no.3
• /
• pp.306-320
• /
• 2015

This survey was carried out in 2014 to estimate the pesticide residue levels in commercial environment-friendly agricultural products in Seoul metropolitan area. Pesticide residues in 27 commodities were examined and analyzed using LC-MS/MS, which can simultaneously detect up to 85 pesticides. A total of 441 samples were collected and analyzed. Among the detected samples, the residue levels in 1.2% of organic agricultural products and 2.2% of pesticide-free agricultural products exceeded the maximum residue limits (MRLs); hence, 1.8% of the total samples exceeded the MRLs. The safety of the detected pesticides was assessed by monitoring the acceptable daily intake level (ADI) and acceptable dietary exposure (ADE) to the pesticides via consumption of the commodities. ADI and ADE are found to be 0.07728-9.46530% and 0.00141-0.17210%, respectively, which means that the residual pesticides in the environmental-friendly agricultural products in Korea are below the safe limit and therefore, pose no potential public health risks.