• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.29 no.5
• /
• pp.389-395
• /
• 2016

In this paper, vibration characteristics in terms of the airfoil cross-sectional shape was examined by using the EDISON co-rotational plane beam-transient analysis. Co-Rotational plane beam analysis is appropriate for large rotation and small strain. Assuming aircraft wing as a cantilevered beam, natural frequencies of each airfoil cross-sectional shape were estimated using VABS program and fast Fourier transformation(FFT). VABS conducts finite element analysis on the cross-section including the detailed geometry and material distribution to estimate the beam sectional properties. Under the same airfoil geometric configuration and material selection, variation of material induced difference in the deflection and natural frequencies. It was observed that variation of the natural frequency was dependent on variation of the airfoil shape and material.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.8
• /
• pp.5318-5326
• /
• 2014

This paper presents the results of flexural test of concrete beams reinforced with GFRP and conventional steel reinforcement for comparison. The beams were tested under a static load to examine the effects of the reinforcement ratio and compressive strength of concrete on cracking, deflection, ultimate capacity, and modes of failure. The test results showed that the ultimate capacity of the GFRP-reinforced beams increased with increasing reinforcement ratio and concrete strength, showing a 41.3~51.6% increase compared to steel reinforced beams. The deflections at maximum loads of the GFRP reinforced beams were 4.1~6.3 times higher that of steel reinforced beams. The measured deflections of GFRP reinforced beams decreased approximately 31% compared to the theoretical predictions because the theoretical flexural stiffness was underestimated at the maximum loads. For the GFRP-reinforced beams, the ACI code 440 design method resulted in conservative flexural strength estimates.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.309-312
• /
• 2008

This paper describes ultimate load tests which were performed to show the effects of prestress loss and tendon corrosion on the flexural strength of post-tensioned concrete beams and the occurrence of wire fracture. Five test specimens were fabricated in laboratory with the variations of the prestress of tendons and the loss of tendon area. For two specimens, small area of tendon at the center of the beam was exposed by using diameter 25mm drill and the exposed tendon was corroded using accelerated corrosion equipment. During the tests, deflections, crack width, and strain changes were measured and acoustic events were monitored with two acoustic sensors. Tests results show that the ultimate flexural strength of test specimens with corroded tendons is smaller than the predicted flexural strength which is calculated considering the loss of tendon area. It is considered that estimation of flexural strength of PSC beams with corroded tendons is very complicated just based on the loss of tendon area obtained by one-side visual inspection.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.11 no.3
• /
• pp.9-15
• /
• 2011

The flexural behavior of the UHPFRC rectangular beam which has 100 MPa, 140 MPa compressive strength were compared with that of the typical RPC rectangular beam which has same geometrical shape, prestressd force and 160 MPa compressive strength. UHPFRC beam was not reinforced at all and the variable of test is fraction of steel fiber, compressive strength of concrete, method of prestressing and ratio of prestressing bar. The behavior of UHPFRC beam was analysed by relationship of moment - curvature and load - deflection. Simple modeling of stress-strain of UHPFRC was proposed. Based on the proposed constituted, the flexural moment-curvature relationship was calculated and compared with experimental data on prestressed UHPFRC beams. Good agreement between calculated strengths and experimental data is obtained.

• Journal of the Microelectronics and Packaging Society
• /
• v.31 no.1
• /
• pp.1-6
• /
• 2024

Spiders detect even tiny vibrations through their vibrational sensory organs. Leveraging their exceptional vibration sensing abilities, they can detect vibrations caused by prey or predators to plan attacks or perceive threats, utilizing them for survival. This paper introduces a nanoscale crack-based sensor mimicking the spider's sensory organ. Inspired by the slit sensory organ used by spiders to detect vibrations, the sensor with the cracks detects vibrations and pressure with high sensitivity. By controlling the depth of these cracks, they developed a sensor capable of detecting external mechanical signals with remarkable sensitivity. This sensor achieves a gauge factor of 16,000 at 2% strain with an applied tensile stress of 10 N. With high signal-to-noise ratio, it accurately recognizes desired vibrations, as confirmed through various evaluations of external force and biological signals (speech pattern, heart rate, etc.). This underscores the potential of utilizing biomimetic technology for the development of new sensors and their application across diverse industrial fields.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.10 no.10
• /
• pp.1183-1188
• /
• 2015

The FM-QCSK(: Frequency Modulated Quadrature Chaos Shift Keying) system is one of the most efficient systems in chaotic literature. One of the problems in this system is that half the bit duration is used for sending a chaotic reference signal which leads to increase the energy losses and reduces the data rate. In this paper, a novel scheme to enhance the performance of FM-QCSK system has been proposed. With the proposed scheme, FM-QCSK would be able to operate at higher data rates with reduced BER(: Bit Error Rate) and energy consumption. The basic modification introduced by the proposed scheme is the use one reference chaotic signal to transmit multi information signals in both in-phase and quadrature-phase channels. The results showed that the proposed scheme have achieved more than 3 dB gains in SNR for AWGN channels respectively at $BER=10^{-3}$ over the conventional one. The results also showed that the optimum number information signals can be send per reference signal is 8.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.2A
• /
• pp.301-310
• /
• 2006

Carbon fiber reinforced polymer (CRFP) materials are well suited to the rehabilitation of civil engineering structures due to their corrosion resistance, high strength to weight ratio and high stiffness to weight ratio. Their application in the field of the rehabilitation of concrete structures is increased due to the vast number of bridges and buildings in need of strengthening. However, RC members, strengthened with externally bonded CFRP plates, happened to collapse before reaching the expected design failure load. Therefore, it is necessary to develop the new strengthening method to overcome the problems of previous bonded strengthening method. This problems can be solved by prestressing the CFRP plate before bonding to the concrete. In this study, a total of 21 specimens of 3.3 m length were tested by the four point bending method after strengthening them with externally bonded CFRP plates. The CFRP plates were bonded without prestress and with various prestress levels ranging from 0.4% to 0.8% of CFRP plate strain. All specimen with end anchorage failed by a plate fracture regardless of the prestress levels while the specimen without end anchorage failed by the separation of the plate from the beam due to premature debonding. The cracking loads was proportionally related to the prestress levels, but the maximum loads of specimens strengthened with prestressed CFRP plates were insignificantly affected by the prestress levels.

• Journal of the Korean Geotechnical Society
• /
• v.22 no.8
• /
• pp.129-136
• /
• 2006

Engineered mixtures, which consist of rigid sand particles and soft fine-grained rubber particles, are tested to characterize their small and large-strain responses. Engineered soils are prepared with different volumetric sand fraction, sf, to identify the transition from a rigid to a soft granular skeleton using wave propagation, $K_{o}-loading$, and triaxial testing. Deformation moduli at small, middle and large-strain do not change linearly with the volume fraction of rigid particles; instead, deformation moduli increase dramatically when the sand fraction exceeds a threshold value between sf=0.6 to 0.8 that marks the formation of a percolating network of stiff particles. The friction angle increases with the volume fraction of rigid particles. Conversely, the axial strain at peak strength increases with the content of soft particles, and no apparent peak strength is observed in specimens when sand fraction is less than 60%. The presence of soft particles alters the formation of force chains. While soft particles are not part of high-load carrying chains, they play the important role of preventing the buckling of stiff particle chains.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.2 no.1
• /
• pp.52-59
• /
• 2014

This study examines the compressive strength, elastic modulus and splitting tensile strength of geopolymer concrete in order to evaluate its mechanical characteristics according to the admixing of fly ash and blast furnace slag. Moreover, identical tests are also conducted considering the amount of powder, the mixing ratio of alkali activator and the mixing ratio of silica fume for further comparative analysis considering various variables. The comparison with the formulae specified in Korean and overseas codes reveal that a mixing ratio of 18% is adequate for the alkali activator and that a replacement ratio of 5% by silica fume is recommended for silica fume. The elastic modulus of the geopolymer concrete appears to increase slightly with the increase of the compressive strength per variable and age and to be smaller than the values predicted by the formulae specified in Korean and overseas codes. In addition, the examination of the stress-strain curves shows that the geopolymer concrete exhibits ductile behavior compared to the conventional OPC. In view of the splitting tensile strength, high strength is observed for a powder content of $400kg/m^3$ and a replacement ratio of 18% by silica fume. The resulting ratio of the compressive strength to the splitting tensile strength is seen to range between 8.7 and 10.2%.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.49 no.1
• /
• pp.19-30
• /
• 2012

For digital data compression, the quantization is the main part of the lossy source coding. In order to improve the performance of quantization, the vector quantizer(VQ) can be employed. The encoding complexity, however, exponentially increases as the vector dimension or bit rate gets large. Much research has been conducted to alleviate such problems of VQ. Especially for high bit rates, a constrained VQ, which is called the sample-adaptive product quantizer(SAPQ), has been proposed for reducing the hugh encoding complexity of regular VQs. SAPQ has very similar structure as to the product VQ(PQ). However, the quantizer performance can be better than the PQ case. Further, the encoding complexity and the memory requirement for the codebooks are lower than the regular full-search VQ case. Among SAPQs, 1-SAPQ has a simple quantizer structure, where each product codebook is symmetric with respect to the diagonal line in the underlying vector space. It is known that 1-SAPQ shows a good performance for i.i.d. sources. In this paper, a study on designing 1-SAPQ for the first-order Markov process. For an efficient design of 1-SAPQ, an algorithm for the initial codebook is proposed, and through the numerical analysis it is shown that 1-SAPQ shows better quantizer distortion than the VQ case, of which encoding complexity is similar to that of 1-SAPQ, and shows distortions, which are close to that of the DPCM(differential pulse coded modulation) scheme with the Lloyd-Max quantizer.