• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.7
• /
• pp.645-653
• /
• 2013

Seoul National University flap(SNUF) blade is a small-scale rotor blade incorporating a small trailing-edge flap control surface driven by piezoelectric actuators at higher harmonics for vibration attenuation. Initially, the blade was designed using two-dimensional cross-section analysis and geometrically exact one-dimensional beam analysis, and its material configuration was finalized. A flap-deflection angle of ${\pm}4^{\circ}$ was established as the criterion for enhanced vibration reduction based on an earlier simulation. The flap-linkage mechanism was designed and static bench tests were conducted for verifying the performance of the flap-actuation mechanism. Different versions of test beds were developed and tested with the designed flap and the selected APA 200M piezoelectric actuators. Through significant improvements, a maximum deflection of ${\pm}3.7^{\circ}$ was achieved. High-frequency experiments were conducted for evaluating the performance, and the transfer function of the test bed was determined experimentally. With the static tests almost complete, the rotor power required for testing the blade in a whirl tower (centrifugal environment) was calculated, and further preparations are underway.

• Journal of the Korean GEO-environmental Society
• /
• v.14 no.7
• /
• pp.19-29
• /
• 2013

Analysis via classical soil mechanics theory is either ineffective or inappropriate for fully describing stress distribution or failure conditions in cold regions, since mechanical properties of soils in cold regions are different from those reported in the classical soil mechanics theory. Therefore, collecting and analyzing technical data, and systematic and specialized research for cold regions are required for design and construction of the structure in cold regions. Freezing and thawing repeat in active layer of permafrost region, and a loading condition affecting the structure changes. Therefore, the reliable analysis of mechanical properties of frozen soils according to various conditions is prerequisite for design and construction of the structure in cold regions, since mechanical properties of frozen soils are sensitive to temperature condition, water content, grain size, relative density, and loading rate. In this research, the direct shear apparatus which operates at 30 degrees below zero and large-scaled low temperature chamber are used for evaluating shear strength characteristics of frozen soils. Weathered granite soil is used to analyzed the shear strength characteristics with varying freezing temperature condition, vertical confining pressure, relative density, and water content. This research shows that the shear strength of weathered granite soil is sensitively affected by various conditions such as freezing temperature conditions, normal stresses, relative densities, and water contents.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.45 no.10
• /
• pp.863-871
• /
• 2017

LMS (least mean square) algorithm widely used in the AVCS (active vibration control system) of helicopters calculates control input using the forward path transfer function and error signal. If the error signal is sinusoidal, it can be represented as the combination of cosine and sine functions with frequency and phase synchronized with the reference signal. The control input also has the same frequency, therefore control algorithm can be simply implemented if the cosine and the sine amplitudes of the control input are calculated and the frequency and phase of the reference signal are used. Calculation of the control input is implemented as simple matrix operation and the change of the control command is slower than the frequency of the error signal, consequently control algorithm can be operated at lower frequency. The signal processing algorithm extracting cosine and sine components of the error signals are modeled using Simulink and PIL (processor-in-the-loop) mode simulation was executed for real-time performance evaluation.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.3
• /
• pp.309-314
• /
• 2014

The structural layout of mechanical and civil structures is commonly obtained using conventional methods. For example, the shape of structures such as electric transmission towers and offshore substructures can be generated systematically. However, with rapid advancements in computer graphic technology, advanced structural analyses and optimum design technologies have been implemented. In this study, the structural shape of a jacket substructure for an offshore wind turbine is investigated using a topology optimization technique. The structure is subjected to multiple loads that are intended to simulate the loading conditions during actual operation. The optimization objective function is defined as one that ensures compliance of the structure under the given boundary conditions. Optimization is carried out with constraints on the natural frequency in addition to the volume constraint. The result of a first step model provides quick insights into the optimum layout for the second step structure. Subsequently, a 3D model in the form of the frustum of a quadrilateral pyramid is developed through topology optimization.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.2
• /
• pp.101-106
• /
• 2007

The optical performance of the mirror for satellite camera is highly dependent on the adhesive properties between the mirror and its support. Therefore, in order to design a mirror with high optical performance, the mechanical properties of adhesives should be well defined. In this paper, the mechanical properties of three kinds of space adhesives are studied. Elastic moduli of the adhesives are determined by tensile tests. Stress-strain relation is obtained by using exponential curve fitting for the adhesive which shows non-linear behavior. In case of the linear behavior material, elastic modulus is calculated through linear curve fitting. For the tensile tests, several points have been selected in the operating temperature range of the adhesive. The elastic modulus of each adhesive is expressed as a function of temperature. Characteristics of the adhesives are discussed regarding their temperature sensitivity.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.10
• /
• pp.51-59
• /
• 2003

A method of autonomous update is presented for onboard orbit propagator. On board propagator is an alternative means that could be used for navigation purpose in case of CPS receiver's failure. Although the ground station is not a able to upload a new propagator, the onboard propagator must be maintained most up-to-date. For this, a filtering technique is proposed wherein GPS data are effectively used to continuously update the on board propagator which was uploaded previously. Even if the ground station has generated the on board propagator based on the wrong information, the onboard propagator with updating scheme can automatically correct the errors in the coefficients of residual reconstruction function. Several scenarios were used to show the validity of the scheme for updating the onboard propagator using KOMPSAT-1 orbit data.

• Journal of Labour Economics
• /
• v.29 no.2
• /
• pp.29-66
• /
• 2006

This study investigates the structural change of wage determination within internal labor market that have occurred around the financial crisis in 1997 by using the personnel data(1996~2000) of a Korean large firm. We take the effect of performance-based pay system to apply on wage determination of workers using Mincerian earnings function estimation. After introducing the annual salary system in the firm, we did not find the fact that the wage effect of seniority decreases, but we found the wage effect of relative evaluation ratings increases. Then, this study identifies the importance of the reward strategy of firm in Korean internal labor market. Finally, we have concluded that although the firm acknowledged the positive effects of performance-based HRM practices, we have not obtained enough evidence on the transformation into such practices because the seniority-based HRM has been traditionally prevalent in the Korean internal labor market.

• 사회경제평론
• /
• v.29 no.1
• /
• pp.1-29
• /
• 2016

This paper looks critically, in the light of the Capital Controversies of the 1950s and the 1960s, at the Neoclassical claim that the Funded-Pension system is economically superior to the Pay-As-You-Go (PAYG) pension system. This claim rests crucially upon the inverse relation between the rate of interest and the volume of investment (the investment demand function) and the positive relation between the capital intensity and labour productivity (the 'intensive- form' production function), The Capital Controversies proved that the two relations do not always hold; then, the claim in question loses much of its ground. Further, the absensce of the relations makes plenty room for effective demand in determining the level of income and the volome of employment even in the long period. This positive role of effective demand in the long period highlights the problems of the Funded-Pension system and, at the same time, supports the competitiveness of the PAYG pension system.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.37 no.2
• /
• pp.95-101
• /
• 2024

This paper introduces an optimized design for a sensor bracket used to measure the wear amount of an automobile brake pad, based on a dynamic kriging surrogate model. During testing, the temperature of the brake pad can increase beyond 600℃, which often causes sensor malfunction. Therefore, it is essential to optimize the shape of the sensor bracket to minimize heat transfer. To reduce the computational cost of the optimization, the heat-transfer simulation is replaced by a dynamic kriging surrogate model. Dynamic kriging utilizes the best combination of correlation and basis functions and constructs an accurate surrogate model. Following optimization, the temperature of the sensor position decreases by 7.57%. The results from the surrogate model under optimum conditions are verified by a heat-transfer simulation, and the design optimization using a surrogate model is found to be effective.

• The Korean Journal of Applied Statistics
• /
• v.9 no.2
• /
• pp.119-134
• /
• 1996

Accelerated life testing (ALT) of a system is commonly used to reduce time and cost. ALT is achieved by subjecting the test systems to more severe conditions than the normal ones to obtain estimates of life distribution under normal condition. The major interest of this research is to use a model of incorporating the common environmental effect on the components serially linked into a system-so called frailty model for the system life time distribution under each stress and to discuss the related data analysis and comparison of the model with the generally used one. The profile likelihood is used to get an initial values required to compute maximum likelihood estimates and simulation is carried for comparison.