• Journal of Welding and Joining
• /
• v.12 no.4
• /
• pp.1-10
• /
• 1994

이 글에서는 비파괴검사개론에 관하여 알아보았다. 1. 비파괴검사의 의의 1.1 비파괴검사의 역사 1.2 비파괴검사의 원리 1.3 비파괴검사의 목적과 역할 1.3.1 품질관리 1.3.2 생산원가의 절감 1.3.3 품질의 평가 1.3.4 점검 1.4 비파괴검사자의 역할 2. 비파괴검사자의 방법 2.1 방사선투과시험 2.1.1 직접촬영법 2.1.2 투시법 2.1.3 전자사진법 2.1.4 계기법 2.2 초음파탐상시험 2.2.1 음향검사와 초음파탐상 2.2.2 초음파의 성질과 종류 2.2.3 접촉매질 2.2.4 초음파 탐상 방법 2.2.5 초음파 탐촉자 2.3 자기탐상시험 2.3.1 자기탐상 원리 2.3.2 자기탐상 방법 1) 자장측정 탐상법 2) 자기기록 탐상법 3) 탐사 코일법 4) 자분탐상시험 2.3.3 자분탐상시험 2.4 침투탐상시험 2.4.1 침투탐상시험의 원리 2.4.2 침투탐상시험법의 기본 1) 침투탐상시험의 종류 2) 현상체의 종류 2.4.3 침투탐상시험의 장단점 2.5 전자유도시험 (와전류탐상법) 2.5.1 와전류의 발생과 탐지 2.5.2 와전류의 탐지 2.5.3 와전류 탐촉자 2.5.4 와전류 탐상시험의 적용과 장단점.

• Journal of Welding and Joining
• /
• v.12 no.4
• /
• pp.35-40
• /
• 1994

비파괴검사(NDT)란 시험품에 손상을 주지 않고 내.외부에 존재하는 불연속부(결함)을 찾아내는 방법으로 다음과 같이 그 종류를 분류할 수 있다. (1) 표면결함 검출을 위한 비파괴검사 - 육안검사(VT) : 확대경 등에 의한 치수, 형상확인 - 자분탐상검사(MT) : 강자성체에 적용, 표면(하) 결함검출 - 침투탐상검사(PT) : 금속, 비철금속에 적용, 표면개구 결함검출 - 와류탐상검사(ET) : 도체 표층부(봉, 관 등) (2) 내부결함 검출을 위한 비파괴검사 - 방사선 투과검사(RT) : 결함의 종류, 형상의 판별 우수 - 초음파 탐상검사(UT) : 균열 등 면상 결함검출 등 우수 (3) 기타 비파괴검사 - Strain 측정 : 안전성 평가 - 음향방출시험(AET) - 누설시험(LT) - 중성자 방사선시험(NRT) 이상에서 보는 바와 같이 여러 종류의 비파괴검사가 있으나, 그 중에서 용접부에 적용되는 가장 일반적인 검사방법인 방사선 투과검사에 대해 기술하고자 한다.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.16 no.3
• /
• pp.162-173
• /
• 1996

Dry magnetic particle inspection(MPI) was performed to detect the surface defects of steel ingot cast billets. Magnetic properties of several materials were characterized by the measurement of the B-H hysteresis curve. The inspection results were evaluated in terms of the magnetizing current, temperature, and the amount of magnetic particles applied to billets. Magnetic flux leakage near the defect site of interest was measured and compared with the results of calculation by the finite element method in the case of direct magnetizing current. Direct and alternating magnetizing currents for materials were deduced by the comparison of the inspections. Results of the magnetic particle inspection by direct magnetizing current were compared with those of finite element method calculations, which were verified by measuring magnetic leakage flux above the surface and the surface defects of the material. For square rods, due to the geometrical effect, the magnetic flux density at the edges along the length of the rods was about 30% of that at the center of rod face for a sufficiently large direct magnetizing current, while it was about 70% for an alternating magnetizing current. Thus, an alternating magnetizing current generates rather uniform magnetic flux density over the rods, except for the region on the face across about 10 mm from the edge. The attraction of the magnetic particle by the magnetic leakage field was nearly independent of the surface temperature of the billets up to $150^{\circ}C$. However, the temperature should have been limited below $60^{\circ}C$ for an effective fixing of gathered magnetic particles to the billet surface using methylene chloride. We also found that the amount of applied magnetic particles tremendously affected the detection capability.

• Journal of the KSME
• /
• v.21 no.6
• /
• pp.428-438
• /
• 1981

초음파탐상은 방사선비파괴검사와 비교할 때, 객관성이 뒤지고 검사기술자의 능력에 따라 탐상 결과가 틀리며 실제로 적용하는 곳도 방사선비파괴검사보다 많지 않다. 또 자분 및 침투탐상검 사도 파이프라인에는 그렇게 많이 적용되지 않는다. 그리고 표면결함을 조사하기 위해서는 육만 또는 외관검사 처리하게 된다. 그러면 가장 많이 이용되고 있는 방사선비파괴감사에 대한 상세한 내용을 설명하기로 한다.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.37 no.1
• /
• pp.44-49
• /
• 2017

본고에서는 열유도 적외선 열화상 기법의 원리와 응용에 있어 기초적인 개념, 특정 상태량 및 실험적 기법에 대하여 소개하도록 한다. 유도 열화상 기법에 적용되는 유도 주파수의 범위는 1500 Hz ~ 52 MHz이며 강자성 강재 단조 부품의 표면결함 검출에 사용되어진다. 균열 검출 감도는 자분탐상기법과 유사하나 필요한 경우 유도 주파수를 낮춤으로서 강재에 숨겨진 결함을 검출할 수 있다. 탄소섬유강화폴리머(CFRP)에서는 섬유 결함을 검출하며, 실리콘 태양 전지에서는 양호한 열적 콘트라스트와 함께 균열을 검출한다. 유도 열화상 기법의 향 후 대표적인 활용분야로는 레일 및 휠과 같은 철도 구성요소에서의 결함 탐상이 있다[1].

• Proceedings of the KSR Conference
• /
• 2010.06a
• /
• pp.571-582
• /
• 2010

Typically nondestructive inspection methods of the large gear units are applied to penetrate non-destructive inspection. Nondestructive penetrating inspection put into the small openings of the defect to penetration liquid, remove to excess penetration liquid on the surface of the gear units, spread with developing solution and we can find the small defect by coating with penetration liquid. However, this method has so many issues because of penetrate nondestructive tests on the gear assembly. The steep angle of screw is hard to achieved full penetration and has the problem to remove the excess. In contrast, the magnetic nondestructive inspection is easy to detect subsurface defects and subtle defects. According to the inspection results the stress concentrates in gear surface, some internal defects and microscopic flaws exist on the gear units are not found to penetrate the nondestructive inspection, but magnetic nondestructive inspection could have found many defect. Therefore, a reasonable method of nondestructive inspection for the large gear units is suitable to magnetic nondestructive inspection.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2006.06a
• /
• pp.287-288
• /
• 2006

Cracks on the cylinder block of diesel engines will often happen due to cyclic load and thermal stress. According to the Classification Societies' rules, welding repairs of cylinder block made of cast irons are generally not permitted. However, such welding repairs became inevitable taking enormous cost and time for their renewal into consideration. In this study repair welding methods for the cylinder blocks, made of gray cast irons were reviewed and the tests of their welds were carried out in order to purpose the repair welding methods of packing seat and o-ring seat of cylinder block and apply them to the practice. It is concluding remarks that the suspected crack by a magnetic particle test due to different magnetic permeability can be identified, which are not associated with a mechanical discontinuity.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.05a
• /
• pp.282-282
• /
• 2004

단조품 후처리 공정은 표면처리, 자분 탐상, 수 검사, 방청, 개수계량 공정으로 이루어져있다. 그러나 우리나라의 단조품 제조 산업에서는 Fig. 1에서 보는 바와 같이 후처리 공정이 작업자의 수작업으로 이루어져 있어서 많은 문제점을 가지고 있다. 표면 처리 공정에서 소재를 장입하는 작업은 작업자의 수작업으로 이루어져 있어서, 작업자는 중량물을 개수하고, 버킷에 담는 작업을 수행해야 한다. 또한, 소재의 이송은 지게차를 이용하고 있어 작업자와 지게차는 같은 작업공간에서 작업을 하게 된다.(중략)

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.2
• /
• pp.535-541
• /
• 2020

FCAW is used mainly in the welding of carbon steel and alloy steel because it can be welded in all positions and can obtain excellent quality at sites with variable working conditions. Recently, many studies in Korea have estimated the fatigue strength, residual stress, and deformation, and to develop a fillet welding process. On the other hand, there have been few studies of the mechanical properties based on the strength, macro and magnetic particle test results for fillet welding. This study shows the following results through fillet welding, macro testing and strength testing using SM490A (solid-structure rolled steel) for thick plates using SS400 (rolled steel) for the upper plate and FCAW. The hardness test, macro test and magnetic particle test were then conducted. The hardness tests showed that all result values were smaller than the KS B 0893 standard values of 350Hv. The macro-test showed that each type of welded part was in a normal organic state and that there were no internal errors, bubbles, or impurities on the front of the welded part. Therefore, there were no concerns about lamination. The magnetic particle examination showed no problems.

• Journal of Power System Engineering
• /
• v.15 no.3
• /
• pp.65-69
• /
• 2011

This paper introduces the multi-coil eddy current sensor and its characteristic in magnetic material gas turbine rotor. In the past, magnetic particle inspection method was used for qualitative defect evaluation in magnetic material gas turbine rotor. And the ultrasonic inspection method was used for quantitative defect evaluation. Nowadays, eddy current method is used in magnetic gas turbine rotor inspection due to advanced sensor design technology. We developed multi-coil eddy current sensor for the rotor dovetail inspection. At first, rotor stress is analyzed for the determination of sensor position and number. The sensor coils are designed to cover the stress concentration area of rotor dovetail. We select optimum frequency according to material standard penetration data and experiment results. The rotor mock-up and artificial defects were made for the signal detection and resolution analysis of multi-coil eddy current sensor. The results show that signal detection and resolution capabilities are enhanced in comparison to the commercialized sensor enough for the gas turbine rotor inspection. So, this developed multi-coil eddy current sensor substituted for commercialized one and it applied in real gas turbine rotor inspection.