• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.05a
• /
• pp.274-274
• /
• 2004

조향성능은 완성된 자동차를 평가하는 아주 중요한 요소이며, 운전자에게 직접적인 영향을 가지는 까닭으로 우선적으로 해결되어야 할 문제이다. 자동차의 조향성능과 관련된 자동차 요소로는 프런트 샤시 모듈이 있으며, 프런트 샤시 모듈의 자세는 구성 요소인 서브프레임의 조립자세에 의하여 결정된다. 서브프레임은 4개의 원통형 지지부로 이루어져 있으며, 차체와의 조립시 지지부에 물리적 접촉이 발생한다. 즉 공간상에서 서브프레임의 자세는 지지부의 조립위치에 의하여 결정이 되며, 서브프레임의 자세를 결정하기 위해서는 지지부에 대한 적절한 해석이 필요하다.(중략)

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.4
• /
• pp.52-59
• /
• 2012

The subframe has been generally manufactured by using stamped steel material. Recently, automotive designers are considering aluminum as lightweight material. This paper describes the development process of an aluminum subframe which is made by high level vacuum die casting process, which is beneficial for minimizing gas contents and material properties. The weight of manufactured subframe is reduced by 4kg with the comparison of steel subframe. The aluminum subframe is packaged for the current vehicle layout and the imposed requirement is to attain a better structural performance that is evaluated in terms of mounting stiffness, noise and vibration, and endurance performance. The NVH evaluation results show that sound level is decreased by 8dB with the help of high roll-rod mounting stiffness as well as high structural modes.

• Composites Research
• /
• v.32 no.1
• /
• pp.21-28
• /
• 2019

Recently, according to environmental regulations, the automobile industry has been conducting various research on the use of composite materials to increase fuel efficiency. However, there has not been much research on lightweight chassis components. Therefore, in this research, the purpose of this study is to apply composite materials to the sub-frame of chassis components to achieve equivalent levels of stiffness, strength, NVH performance and 50% lightweight compared to the steel sub-frame. First, the Natural frequency of steel and composite specimens was compared to the damping characteristics of composite materials. Then, in this study, the Lay-up Sequence was derived to maximize the stiffness and strength of the sub-frame by applying composite materials. And this lay-up Sequence is proposed to avoid heat shrinkage due to curing during manufacturing. This process was designed based on a FEM structural analysis, and a Natural frequency and frequency response function graph was confirmed based on a modal analysis. The prototype type composite sub-frame was manufactured based on the design and the F.E.M analysis was verified through a modal experiment. Furthermore, it was fitted to the actual vehicle to verify the natural frequency and the indoor noise vibration response, including idling and road noise. This result was confirmed to be equivalent to the steel sub-frame. Finally, the composite sub-frame weight was confirmed to be about 50% of the steel sub-frame.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.3 no.4
• /
• pp.7-12
• /
• 2004

Inspection and analysis are essential process to determine whether a completed product is in given specification or not. Analysis of products with very complicated shape is difficult to carry out direct comparison between inspected coordinate and designed coordinates. So process called as matching or registrations is needed to solve this problem. By defining error between two coordinates and minimizing the error, registration is done. Registration consists of translation, rotation and scale transformations. Error must be defined to express feature of inspected product. In this paper, registration algorithm is developed to determine pose of sub-frame at assembly with body of automobile by defining error between two coordinates considering geometric feature of sub-frame.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.5
• /
• pp.100-105
• /
• 2008

In the design process of an automobile part, several analysis methods are usually utilized to evaluate the performance of the part. However, most automobile design engineers do not directly utilize CAE (Computer Aided Engineering) tools since specific skills are required to obtain practical results. Moreover, CAE requires a huge amount of computation time and cost. In order to resolve these problems, a new design approach named First Order Analysis (FOA) technique has been proposed. In this paper, the FOA technique is employed to design a vehicle sub-frame. An equivalent model of the vehicle sub-frame which only consists of beam elements is proposed and the modal properties obtained with the model are compared to those obtained with a full scale finite element model. The effect of some parameter tolerances on the modal characteristics of the vehicle sub-frame is investigated by employing the FOA equivalent model.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.4
• /
• pp.179-185
• /
• 2008

The purpose of this paper is to propose a systematic method on the weld pitch design of a vehicle sub-frame considering the fatigue life of spot welding points. The input data, which perform the fatigue analysis on the spot welding nuggets, are obtained by both the dynamic analysis of the multi-body vehicle model passing through the virtual proving ground of a typical Belgian road and the quasi-static analysis with the finite element model of the vehicle sub-frame. By utilizing the life cycle data obtained from the fatigue analysis, the welding points to perform the pitch change are determined. The sensitivity analysis on the fatigue life of the welding points is carried out by using the three-level orthogonal array design, and through the results of the sensitivity analysis, the best combination on the welding pitch is determined. This study shows that as compared with the baseline design, the sub-frame redesigned by the proposed technique improves the fatigue life about 7 percent while reducing the number of welding points about 19 percent.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2000.10a
• /
• pp.153-157
• /
• 2000

This paper presents possible defects when welded blank hydroforming and focus on wrinkling, and the die design to prevent this defect An explicit finite element code, PAM-STAMP, is used to simulate welded blank hydroforming process. The numerical results are compared to the experimental results in the aspect of deformed shape. An automobile subframe is taken as an example to carry out finite element analysis.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.3
• /
• pp.77-82
• /
• 2012

It is well known that the targeted fuel efficiency could only be achieved by more than 40% reduction of the vehicle weight through improved design and extensive utilization of lightweight materials. In order to obtain the goal of the weight reduction of automobiles, the researches about lighter and stronger rear sub-frame have been studied without sacrificing the safety of rear sub-frame. In this study, the weight reduction design process of rear sub-frame could be proposed based on the variation of von-Mises stress contour by substituting an AA6061 (aluminum 6061 alloy) having tensile strength of 310 MPa grade instead of SAPH440 steels. In addition, the stress ratio variations (stress over fatigue limit) of the rear sub-frame were examined and compared carefully. It could be reached that this approach method could be well established and be contributed for light-weight design guide and the optimum design conditions of the automotive rear sub-frame development.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.9
• /
• pp.1-6
• /
• 2018

Hydro-forming technology has spread dramatically throughout automotive industry over the last 20 years. This technology has many advantages for automotive applications in terms of better structural integrity of the parts, lower cost from fewer parts, material savings, weight reduction, lower springback, improved strength, durability, and design flexibility. In this study, various simulation technologies were developed to investigate the formability of hydro-forming components. Through this technology, to establish the effective forming process for appropriate components design, the bending process, pre-forming process, die closing process, etc. were considered for good forming. This paper proposes the forming amount, section length (corresponding to the hydro-forming press capacity), and minimum curvature (curvature effect evaluation according to the hydro-forming pressure) among the considerations in the design of the hydro-forming part. In addition, a design method is proposed for hydro-forming molding by carrying out cross section analysis of a real sub-frame part for automobiles. The effects of pre-bending, axial feed, hydraulic pressure, press load, and friction among the hydro-forming process parameters were analyzed. Therefore, whether these processes are necessary factors for hydro-forming were examined.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.3
• /
• pp.38-43
• /
• 2008

The hydroforming technology has been spreaded dramatically in automotive industry last 10 years. Itmay cause many advantages to automotive applications in terms of better structural integrity of the parts, lower cost from fewer part count, material saving, weight reduction, lower springback, improved strength and durability and design flexibility. In this study, the whole process of rear sub-frame parts development by tube hydroforming using steel material having tensile strength of 440MPa grade is presented. At the part design stage, it requires feasibility study and process design aided by CAE (Computer Aided Design) to confirm hydroformability in details. Effects of parameters such as internal pressure, axial feeding and geometry shape in automotive rear sub-frame by hydroforming process were carefully investigated. Overall possibility of hydroformable sub-frame parts could be examined by cross sectional analyses. Moreover, it is essential to ensure the formability of tube material on every forming step such as pre-bending, preforming and hydroforming. In addition, all the components of prototyping tool are designed and interference with press is examined from the point of geometry and thinning.