• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.4
• /
• pp.184-192
• /
• 2001

Cam/tappet wear is one of the critical concerns in valve train deign. Maximum contact stress and minimum oil film thickness between the cam and tappet are usually checked for the estimation of wear characteristics. If the two extreme cases arise simultaneously, there is a strong possibility of cam/tappet wear. In this paper, effects of valve train layout on the wear characteristics were studied. Especially for swinging arm type valve trains, initial geometric layout must be very carefully defined to avoid wear problems. The study was performed fur an end pivot type OHC valve train, which had severe wear problems. Analysis results show that some geometric parameter affect very sensitively on the wear characteristics. Experiments were also performed for the original and modified valve trains, which strongly support the analysis results.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.5
• /
• pp.7-15
• /
• 2009

This paper introduces a new variable valve actuation mechanism with movable second cam center. Valve lift and open duration can be continuously varied according to engine speed and load conditions. A new method to analyze the kinematic relations between the first and second cam profiles and valve motion are also introduced. Because of rocker motion of the second cam, conventional motion conversion program could not be used in this problem. An example shows continuous variations of valve motion and adequate ramp incorporation throughout all valve lift modes. Valve acceleration profile at the high lift mode is similar to that of conventional valvetrains. Contact geometry analysis of the mechanism gives basic information on the load conditions between the components.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.4
• /
• pp.139-148
• /
• 2006

Valve train is one of the important noise sources in idling engines. Valve train noise comes mostly from two different impacts. One is the impact between cam and tappet at the beginning of the valve open period, which is an important source of impulsive noise of valve trains. The other is the impact between valve and valve seat at the closing of the valve open period. In case of mechanical lash adjusters, it is very difficult to control the initial impact. In this paper, we designed various types of cam profiles, especially in the opening ramp design, and investigated the effect of cam profiles on the magnitude of the initial impact. The effects that some cam design parameters have on the impulsive noise are also observed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.4
• /
• pp.63-71
• /
• 2009

The elastic effects of the valve train components are analyzed by using the finite element models of the rocker arm and valve. The whole equations of motion of the valvetrain of an internal combustion engine formulated by finite element techniques are solved by imposing the contact conditions with the augmented Lagrange multiplier method. The velocity and acceleration constraints as well as the displacement constraints are imposed on the contact points. The numerical simulations show that, even if the magnitude of the elastic deformation of the components is very small, it may have large effects on the valvetrain dynamics of a high-speed engine.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.6
• /
• pp.1-8
• /
• 2004

In this paper we present the effects that valve train design parameters and operating conditions have on the valve rotation properties of a diesel engine. Rotation of intake and exhaust valves are very closely related to the long term durability of diesel engines. of the valves do not rotate even at a rated engine speed, it causes the uneven wear of the valve seat and valve head contact area, which eventually shortens the engine life. Because the rated speed of a diesel engine is relatively lower than that of a gasoline engine, the operating condition of a diesel engine produces tough environment for valve rotation. Therefore, the valve rotation is an important problem which should be solved in the early stage of engine development. In this study, we developed a new technique to measure the valve rotation and shaking motion simultaneously using three proximity sensors. Valve train rotating properties of a diesel engine were measured under various engine operating conditions.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.1
• /
• pp.125-132
• /
• 2011

The dynamic characteristics of valve train are responsible for the dynamic performances of engine. We derived the equation of motion for 6 degrees of freedom model of the valve train. Computer model is also developed with flexible multibody model considering contact between components. The simulation results with these two models are compared with experimental results. We investigated the effect of the two spring models, TSDA (Translational Spring Damper Actuator) element and flexible body model, on the valve behavior and spring force. It is found that the dynamic behavior of the two models are not very different at normal operational velocity of the engine. By modeling contact between cam and tappet, the stress distributions of the cam were found. Using stress distribution obtained, contact width and contact stresses of the cam surface were calculated with Hertz contact theory.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.2
• /
• pp.184-193
• /
• 2006

Rotation of intake and exhaust valves are very closely related to the long term durability of automotive engines. If the valves do not rotate even at a rated engine speed, it causes the uneven wear of the valve seat and valve head contact area, which eventually shortens the engine life. A principle of valve rotation mechanism was presumed based on some findings from experiments, and computer programs were developed to simulate the valve rotation phenomena. In this study we investigated the valve rotation mechanism by using the computer simulation models.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1998.04a
• /
• pp.342-346
• /
• 1998

최근의 자동차엔진에서 사용되는 윤활유에는 여러 가지 첨가물이 사용된다. 특히 고분자량 폴리머계의 점도 지수 향상제를 윤활유의 원유에 첨가함으로써 온도 증가에 따른 점도 불안정성을 방지하는 다등급 윤활유 성격을 얻을 수 있다. 그러나 이러한 고분자량 폴리머계의 첨가물은 고온의 엔진 운전 조건에서 윤활유의 점도 안정성을 보장해줌에도 불구하고 엔진 부품들의 정상적인 운동 속도에서도($1-^6 S^{-1}$) 고 전단 변형율 속도로 인하여 유막 감소 효과를 발생 시킨다. 또한 이 첨가제들은 엔진 부품의 마찰 표면에 큰 전단 응력을 지닌 끈끈한 형태의 경계막을 형성한다. 고분자량 폴리머계의 점도 지수 향상제에 대한 예기치 못한 영향은 유막 감소 효과로 인하여 엔진 부품간의 마모를 증가 시키고 점도의 감소로 마찰을 감소 시키는 반면 경계막으로 인하여 고체면이 보호를 받는데 있다. 이러한 유막 형성의 물리적인 개념에 대하여 고체면의 끈끈한 경계막의 존재 효과와 두 경계막 사이에서 일어나는 유막 감소 효과를 표현할 수 있는 현실적인 해석의 필요성이 제기된다. 본 연구는 최근에 많이 쓰이고 있는 점도 향상제가 첨가된 윤활유가 자동차 밸브 트레인 시스템에서 유막 형성에 미치는 영향을 마찰 효율과 마모 방지의 입장에서 고찰하였다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.2
• /
• pp.31-39
• /
• 2003

Numerical analysis for valve train dynamics of an internal combustion engine is presented. The components of the valve train are modeled by finite element techniques, and the dynamic contacts between the components are analyzed by the solution strategies of differential algebraic equations. Also an iterative scheme similar to the augmented Lagrange multiplier method is employed to enforce the contact constraints. It is shown that the contact and separation between the components of the valve train can be computed by the finite element techniques, and the numerical examples are presented to demonstrate the efficiency of the solution.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.5
• /
• pp.90-99
• /
• 1995

A numerical method is proposed to synthesize automotive cam profiles. An arbitrary acceleration profile for the cam follower motion is divided into several segments, each of them is described by a Hermite curve. A cam profile is defined by control point locations and control variables assigned to each segment. Closed form equations are derived for velocity and displacement constraints which should be satisfied for the curve to be a cam profile. Because the method is flexible and provide arbitrary local controllability, any types of cam acceleration profile can be reproduced by the method. The method is expecially useful for the design of roller type OHC valve trains which need precise local control in the cam profile design to avoid under-cutting problems.