• Membrane Journal
• /
• v.24 no.3
• /
• pp.213-222
• /
• 2014

In this study, 2-stage recirculation membrane process was developed for purification of high purity bio-methane for the vehicle fuel application. Pure gas permeation and mixture gas permeation test were done as a function of methane content and pressure in the feed using polysulfone membrane modules. 2-stage membrane plant was designed, constructed in a food waste treatment cite. Dehumidification, dry desulfurization, and desiloxane plants are installed for the removal of $H_2O$, $H_2S$ and siloxane in the biogas. Permeation test were done with the pre-treated methane mixture in terms of methane purity and recovery by adjusting the ratio of membrane area (1:1, 1:3, 2:2) in the first and second membrane modules in the plant. When membrane area of 2 stage increased to $3m^2$ from $1m^2$ at 1-stage membrane area of $1m^2$, the feed rate and $CH_4$ recovery at 95% methane purity were increased from 47.1% to 92.5% respectively. When the membrane area increased two-fold (1:1 to 2:2), $CH_4$ recovery increased from 47.1% to 88.3%. When the feed flow rate was increased, in 1:3 ratio, final purity of the methane is reduced, the methane recovery is increased. When operating pressure was increased, the feed rate was increased and recovery was slightly decreased. From this result, membrane area, feed pressure and feed rate could be the important factor to the performance of the membrane process.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.13 no.2
• /
• pp.5-13
• /
• 1976

An analytical and experimental design procedure is described for the Capacitor Discharge Ignition (CDI) System with a view to fuel saving ann reduction of gas exhaustion and maintenance need. Specifically, the input and output voltage and current of a given ignition coil were calculated by using a simplified circuit model for the discharging system. The results were compared with the experimental results, from which ratings of the charging capacitor, the SCR and the diodes and the required output valtage of the DC.DC converter were determined so as to satisfy the optimum ignition conditions. Protection circuits for excessive dv/dt and di/dt for the SCR were also analyzed and the results were compared with the observed results, which facilitate selection of the SCR and design of the protection circuit and the trigger circuit. Also, design of the DC.DC converter was simplified based on the analysis and experimental results of the behavior of the converter, An experimental, yet practical CDI system was built, which showed satisfactory performance in the laboratory and field tests. The results were also reported.

• Journal of Korean Society for Atmospheric Environment
• /
• v.32 no.6
• /
• pp.593-602
• /
• 2016

The physicochemical characteristics of particulate matter emissions from various vehicle's fuel types were studied at the facility of Transport Pollution Research Center(TPRC), National Institute of Environmental Research (NIER), Korea. Three different types of fuels such as gasoline, liquefied petroleum gas (LPG) and diesel were tested on the NIER driving mode and the constant speed modes(30, 70, and 110 km/h). Chemical composition of submicron particles from vehicle emissions was measured by the High Resolution Time of Flight Aerosol Mass Spectrometer (HR-ToF-AMS) during running cycles. Organics were dominant chemical species of particulate matter emissions for all three different vehicles' fuel types. Moreover, regardless of fuel types, emission rate of organics and inorganics decreased as the average speed of vehicle increased. The portion of fully oxidized fragment families of $C_xH_yO_z$ accounted for over 98% of organic aerosol(OA) in LPG and diesel vehicles, while the relatively high fraction of $C_xH_y$ in OA was observed in gasoline vehicle.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.12 no.6
• /
• pp.571-576
• /
• 2002

There have been a lot of considerations dealing with improving the performance of neuro-fuzzy system. The studies on the neuro-fuzzy modeling have largely been devoted to two approaches. First is to improve performance index of system. The other is to reduce the structure size. In spite of its satisfactory result, it should be noted that these are difficult to extend to high dimensional input or to increase the membership functions. We propose a novel neuro-fuzzy system based on the efficient clustering method for initializing the parameters of the premise part. It is a very useful method that maintains a few number of rules and improves the performance. It combine the various algorithms to improve the performance. The Expectation-Maximization algorithm of Gaussian mixture model is an efficient estimation method for unknown parameter estimation of mirture model. The obtained parameters are used for fuzzy clustering method. The proposed method satisfies these two requirements using the Gaussian mixture model and neuro-fuzzy modeling. Experimental results indicate that the proposed method is capable of giving reliable performance.

• The Korean Journal of Air & Space Law and Policy
• /
• v.25 no.2
• /
• pp.201-230
• /
• 2010

With starting the industry of automobiles, railroads and mining, the legal principle of "erlaubtes Risiko" that began as a means of maintaining the revitalized world for the cause of social utility has interpreted as a system of negligence theory in the precedent while it has gained academic recognition. Yet in aircraft operation, which is one area of high technology, CAT which can be the cause of some accidents or events or thunderstorm with turbulence is an abnormal meteorological phenomenon with frequent change that cannot be monitored perfectly just as some patient with unstable condition and that cannot be ascertained about not only the possibility of its happening but also the degree of how big the accident is. Yet the use of jet current which has the possibility of CAT can be an act of high social utility where we not only drastically cut down on time fuel also guarantee the arrival and departure on schedule when landing in airports that have thunderstorm which does not appear as fatal risk. Although we could take some measures where we can predict and avoid the potential risk, easing the regular duty of care is necessary by applying the legal principles of permitted risk concerning the incidents and accidents caused by operating in areas with the risk of turbulence or CAT with the low probability by the reason of social utility.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.2
• /
• pp.183-190
• /
• 2015

An ejector is a type of non-powered pump that is used to supply a secondary flow via the ejection of a primary flow. It is utilized in many industrial fields, and is used for fueling the vehicle because of less failures and simple structure. Since most of ejectors in industry are gas-to-gas and liquid to gas ejector, many research activities have been reported in optimization of gas ejector. On the other hand, the liquid ejector is also applied in many industry but few research has been reported. The liquid ejector occurs cavitation, and it causes damage of parts. Cavitation has bees observed at the nozzle throat at the specified pressure. In this study, a two-dimensional axisymmetric simulation of a liquid-liquid ejector was carried out using five different parameters. The angle of the nozzle plays an important role in the cavitation of a liquid ejector, and the performance characteristics of the flow ratio showed that an angle of $35^{\circ}$ was the most advantageous. The simulation results showed that the performance of the liquid ejector and the cavitation effect have to be considered simultaneously.

• Journal of the Korean Society of Groundwater Environment
• /
• v.7 no.1
• /
• pp.55-58
• /
• 2000

Methyl tertiary butyl ether (MTBE) is a gasoline additive that boosts the oxygen content in fuel (an oxygenate), resulting in less air-polluting carbon monoxide being released from vehicle exhaust systems. Then, groundwater contamination problems have been developed in areas where the chemical is used. Common sources of water contamination by MTBE include leaking underground gasoline storage tanks and leaks and spills from above ground fuel storage tanks, etc.. Studies on the chemical and these problems are going on abroad vigorously. These studies should be performed in our country as well more actively. This paper reviews on articles on these studies and focuses on the identification of the chemical as a groundwater contamination source.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.1
• /
• pp.666-671
• /
• 2018

A honeycomb panel is a plate made by attaching two surface plateson eitherside of a honeycomb core. The honeycomb plate hasexcellent specific strength and energy absorption and is suitable for use in regions where good impact resistance is required. Recently, with the increasing the need for a lightweight design to facilitate transportation, numerous studies have been conducted using aluminum honeycomb plates as body materials for vehicles such as automobiles and high-speed trains. In addition, honeycomb plates have excellent sound deadening properties, as well as excellent heat insulation and durability. Savings in weight using lightweight materials such as aluminum alloy for honeycomb panel's skin can lead to increase fuel economy and reduction in air pollution. In this study, in order to improve the design technology of the honeycomb plate material, the manufacturing technology of the aluminum honeycomb core and honeycomb plate material and various mechanical properties of the honeycomb plate were evaluated. From the results, it was found that the design of the manufacturing process of the aluminum honeycomb plate, as well as itsproduction and characteristics, were improved. The resulting excellent energy absorption capability of the honeycomb plate was due to the repetitive core buckling, indicating that the higher the compressive strength, the higher the strength per bonded area.

• Journal of Arbitration Studies
• /
• v.18 no.2
• /
• pp.201-233
• /
• 2008

러시아와 한국간의 공식적인 접촉은 1990년 6월 샌프란시스코에서 개최된 정상회담이다. 동년 9월 뉴욕에서 개최된 양국의 외무장관 회담에서 러시아와 한국의 외교관계가 수립되었다. 그간 양국간에는 협정을 통한 협력의 법적기반이 조성되었는데 주요 분야를 보면 무역, 투자보장, 어업, 이중과세방지, 군사기술분야, 원자력의 평화적 이용, 문화교류에 관한 협정들이 있다. 역시 양국간의 주요 관심사항은 무역과 경제협력 분야이다. 2007년도 러시아와 한국의 무역액은 150억 달러를 초과함으로써 전년도에 비해 55.5% 증가하였다. 러시아의 한국으로의 수출은 약 70억 달러로서 전년도에 비해 52.6% 증가했고 한국으로부터의 수입은 80억 달러를 초과함으로써 전년도에 비해 56.1% 증가하였다. 그리하여 러시아는 한국의 10대 교역국으로 성장하였다. 가스와 오일 프로젝트 추진과 관련하여 사할린지역에서 사용하기 위해 한국으로부터 수입하는 드릴기계장비, 탱커, 자동차, 휴대전화는 한국과 러시아 양국간 경제성장의 주요요인이 되고 있다. 2008년 1/4 분기 양국간 무역액은 42억 달러를 초과했는데 이는 전년도 동기와 비교해서 72.1% 증가한 것이다. 이 중 한국에의 수출은 17억 달러를 초과했는데 이는 전년도 1/4분기에 비해 91.7% 성장한 것이다. 한국으로부터의 수입은 약 25억 달러로서 전년도 1/4 분기와 대비해서 60.6% 성장했다. 러시아와 한국간의 경제교류가 크게 증대하게 된 배경에는 러-한경제과학기술협력공동위원회가 큰 역할을 담당했다. 이 논문에서 필자는 무역과 투자측면에서 본 양국간 경제협력의 특징을 고찰하는 한편 러시아의 동부지역(러시아 극동 및 바이칼횡단지역)과 한국과의 협력과 관련된 역동성과 과제를 제시하는데 연구의 목적을 두었다. 한국은 외국기업과 함께 러시아 극동지역의 무역과 경제협력 증진에 상당한 공헌을 함으로써 러시아 극동경제권에서 주요 무역파트너가 되고 있다. 또한 본 연구에서는 한국과 러시아간의 주요 협력프로젝트에 관하여 고찰하는 한편 앞으로의 전망을 제시하였다. 이 문제는 무엇보다도 한-러간의 공동 에너지프로젝트 및 에너지자원의 무역과 관련되어 있다. 한국과 러시아는 이미 많은 분야에서 상당한 정도로 상호 협력관계를 발전시켜왔다. 여기에는 정책, 에너지, 경제, 문화, 과학기술 분야가 포함되어 있다. 현재 러시아와 한국간에는 에너지 분야에서의 전략적 대화채널 구축에 관한 문제와 함께 연료 및 에너지공단 건설과 관련하여 협력문제가 논의되고 있다. 에너지 분야에서의 전략적 대화개념 구축을 위해서는 전략, 예측 및 투자환경의 문제가 양국간에 집중논의 되어야 하고 법제상의 조화문제도 논의되어야 한다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.2
• /
• pp.219-226
• /
• 2010

The stamping process is widely used in fabricating various sheet-parts for vehicle, airplane, and electronic devices due to its low processing cost and high productivity. Recently the use of thin sheets with corrugated structures has rapidly increased for the production of energy devices, e.g., heat exchangers and fuel cells. However, it is very difficult to make corrugated structures directly in the stamping process due to their geometrical complexity. To solve this problem, this paper proposes a multi-step stamping process with a combined heat treatment process: a sequence of the first stamping, heat treatment, and second stamping. By multi-stamping, we obtained successful results in fabricating very thin corrugated structures with thicknesses of $100{\mu}m$; these are applicable as part of a plate-type heat exchanger.