• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.2B
• /
• pp.187-192
• /
• 2011

Nitrate nitrogen is common contaminant in groundwater aquifers, its concentration is regulated many countries below 10 mg/L as N (As per WHO standards) in drinking water. An attempt was made to get optimal results for the treatment of nitrate nitrogen in groundwater by conducting various experiments by changing the experimental conditions for ZVI bipolar packed bed electrolytic cell. From the experimental results it is evident that the nitrate nitrogen removal is more effective when the reactor conditions are maintained in acidic range but when the acidic environment changes to alkaline due to the hydroxide formed during the process of ammonia nitrogen there by increasing the pH reducing the hydrogen ions required for reduction which leads to low effectiveness of the system. In the ZVI bipolar packed bed electrolytic cell, the packing ratio of 0.5~1:1 was found to be most effective for the treatment of nitrate nitrogen because ZVI particles are isolated and individual particle act like small electrode with low packing ratio. It is seen that formation of precipitate and acceleration of clogging incrementally for packing ratio more than 2:1, decreasing the nitrate nitrogen removal rate. When the voltage is increased it is seen that kinetics and current also increases but at the same time more electric power is consumed. In this experiment, the optimum voltage was determined to be 50V. At that time, nitrate nitrogen was removed by 94.9%.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.21 no.6
• /
• pp.225-229
• /
• 2011

Most of the silicon cutting methods using the multi-wire with the slurry injection have been used for wafers of the crystalline solar cell. But the productivity of slurry injection cutting type falls due to low cutting speeds. Also, the direct contact with the metal wire and silicon block increases the concentration of metallic impurities in the wafer's surface. In addition, the abrasive silicon carbide (SiC) generates pollutants. And production costs are rising because it does not re-use the worn wire. On the other hand, the productivity of the cutting method using the diamond coated wire is about 2 times faster than the slurry injection cutting type. Also, the continuous cutting using the used wire of low wear is possible. And this is a big advantage for reduced production costs. Therefore, the cutting method of the diamond coated wire is more efficient than the slurry injection cutting technique. In this study, each cutting type is analyzed using the surface characteristics of the solar wafer and will describe the effects of the manufacturing process of the solar cell. Finally, we will suggest improvement methods of the solar cell process for using the diamond cutting type wafer.

• Journal of Life Science
• /
• v.21 no.3
• /
• pp.444-450
• /
• 2011

Perchlorate ($ClO_4^-$) is a contaminant found in surface water and soil/ground water. Autotrophic perchlorate-reducing bacteria (PRB) use hydrogen gas ($H_2$) as an electron donor to remove perchlorate. Since iron corrosion can produce $H_2$, feasibility of autotrophic perchlorate-removal using zero-valent iron (ZVI) was examined in this study using activated sludge that is easily available from a wastewater treatment plant. Batch test showed that activated sludge microorganisms could successfully degrade perchlorate in the presence of ZVI. The perchlorate biodegradation was confirmed by molar yield of $Cl^-$ as perchlorate was degraded. Scanning electron microscope revealed that rod-shaped microorganisms on the surface of iron particles used for the autotrophic perchlorate-removal, suggesting that iron particles could serve as supporting media for the formation of biofilm as well. DGGE analyses revealed that microbial profile of the inoculum (activated sludge) was different from that of biofilm sample obtained from the ZVI-added enrichment culture used for $ClO_4^-$-degradation. A major band of the biofilm sample was most closely related to the class Clostridia.

• Journal of Korean Society of Environmental Engineers
• /
• v.32 no.10
• /
• pp.957-964
• /
• 2010

The deactivated catalyzed diesel particulate filter-trap (DPF) was remanufactured by ultrasonic wave treatment with various prepared solutions, followed by active component re-impregnation, and the emission control performance and surface properties of remanufactured DPF were studied at various remanufacturing conditions. The proper ultrasonic wave cleaning time at various prepared solutions and optimal re-impregnation amounts of active component for the best emission control performance of DPF were investigated and its performance tests were also carried out with various temperatures for the conversions of CO, THC (total hydrocarbon) and PM (particulate matter) by catalytic reaction test unit using bypass gas from the diesel engine dynamo system. It was found that the emission control performance of DPF remanufactured with the high-temperature air washing, ultrasonic wave cleaning at acid/base solutions and active component re-impregnation method was recovered to 95% level of its activity compared to that of the fresh DPF, which was caused by removing the deactivating materials from the surface of the DPF, through the analyses of performance test and their surface characterization by Optical microscope, EDX, ICP, TGA, and porosimeter.

• Journal of Wetlands Research
• /
• v.21 no.2
• /
• pp.173-180
• /
• 2019

This study was conducted to understand factors affecting TSS and heavy metals transport on the road, parking lot and roof. During storm events, heavy metals, which were mostly attached to TSS, were also transported when TSS was washed off in the road, parking lot and roof. This finding may be supported by the significant correlations between TSS load and total and soluble heavy metals load including Cr, Fe, Cu, and Pb (Pearson r value: 0.52 to 0.73; probability p value<0.01). Generation and transport of TSS and heavy metals were greater in the road and parking lot compared to the roof due to vehicular activities, slope and greater catchment areas of these sites. It was found that TSS transport during peak flows of storm events ranges from 65% to 75% implying that by controlling peak flows, TSS transportation to nearby water bodies may be decreased. Depending on the target TSS and heavy metal reduction, sizing of low impact development (LID) technologies and green infrastructures (GI) such as infiltration trench, tree box filter, and rain garden may be calculated. Future researchers were recommended to assess the limitations of the systems and determine the design considerations for these types of facilities.

• Journal of Korean Society on Water Environment
• /
• v.29 no.3
• /
• pp.383-392
• /
• 2013

In this research, mixing behavior of the floating pollutant such as oil spill accidents was analyzed by studying the advection-diffusion of GPS floaters at water surface. The LPT (Lagrangian Particle Tracking) model of EFDC (Environmental Fluid Dynamics Computer Code) was used to simulate the motion of the GPS floater tracer. In the field experiment, 35 GPS floaters were injected at the Samun Bridge of Nakdong River. GPS floaters traveled to downstream about 700 m for 90 minutes. The field data by the GPS floater experiments were compared with the simulation in order to calibrate the parameter of LPT model. The turbulent diffusion coefficient of LPT model was determined as $K_H/hu^*$ = 0.17 from the scatter diagram. The arrival time of peak concentration and transverse diffusion from the simulation results were similar with the experiments from the concentration curves. Numerical experiments for anticipation of damage from floating pollutant were conducted in the same reach of the Nakdong River and the results show that the pollutant cloud transported to the left bank where the Hwawon pumping station is located. For this reason, it is suggested that the proper action should be needed to maintain the safety of the water withdrawal at the Hwawon pumping station.

• Journal of Environmental Health Sciences
• /
• v.43 no.3
• /
• pp.202-213
• /
• 2017

Objectives: HRA (Health Risk Assessment) is an important tool for measuring the health impacts of air pollution. HRA is already being used widely as an important reference for crafting air pollution policies. However, the absence of a domestic CRF (Concentration Response Function) standard, which is a main component for HRA, could cause confusion amongst policy-makers. The purpose of this study is to tabulate a domestic CRF standard for a PM (Particulate Matter)-related HRA. Methods: This study suggested a domestic CRF standard for HRA thorough a literature review. The literature review for meta-analysis was limited to the English language for epidemiological studies published from January 1980 to March 2016. This meta-analysis was conducted by assuming both fixed- and random-effects of CRF. In addition, studies that reported HRA of air pollution for WHO (World Health Organization), the EC (European Commission), and the EPA (Environmental Protection Agency) were reviewed to compare the CRFs of South Korea to the recommended CRFs of WHO, the EC, or the EPA. Additionally, a domestic CRF standard was supplemented by these. Results: Nineteen studies were selected for the CRF for South Korea. Fifty-three CRFs were derived for meta-analysis. CRFs with a standard for PM-related HRA were divided according to the following four criteria: air pollution, exposure characteristics, type of health impact, and age group. Finally, a domestic CRF standard was created comprised of 21 CRFs. Among these, six CRFs were derived from the results of foreign HRA studies. Conclusions: This study is important in that a domestic CRF standard is first suggested. In addition, this study suggests a further area of study for using HRA as a policy tool and a direction of epidemiological study.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.29 no.2
• /
• pp.210-216
• /
• 2002

Air abrasion technology can prepare enamel and dentin for bonding, similar to etching by acidic gels and solutions. Longer treatment can excavate pit and fissures, preparing the tooth for immediate placement of bonded resin materials. Although not appropriate for every clinical situation, the air abrasive technology minimizes heat, vibration and bone-conducted noise associated with conventional means of caries removal since the cutting is accomplished by air pressure. Also, patients treated with the air-abrasion technology rarely request anesthesia. Air abrasion technology was more effective in treating early carious lesions and stains compared to lesions where caries had already progressed to produce soft dentin and the strong air stream and noise caused by the evacuation system was a major discomfort to pediatric patients, and the experience and skillfulness of clinician should be required for accurate and proper tooth preparation.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.148-148
• /
• 2013

스퍼터 이온펌프(Sputter Ion Pump)는 주로 화학흡착으로 동작하며 기계적 진동이 없고, 기름 등의 오염 물질을 배출하지 않으며, 수명이 길어 초고청정 진공이 요구되는 표면실험장치, 표면분석계, 입자가속기 등에서 널리 사용 되고 있다. 일정한 지름을 갖는 다수의 원통 양극과 그 양단에 두개의 음극판을 배치시킨 후, 양극과 음극 사이에 수 kV의 전압을 걸고 원통의 축방향으로 자장을 인가하면 페닝 방전이 발생한다. 냉음극에서 방출된 전자는 양극으로 비행하면서 가스를 이온화한다. 이온분자는 가스흡수성 게터재료로 된 음극에 충돌하여 스퍼터링을 일으키며 게터막를 주변에 증착시킨다. 이온 및 중성 가스는 게터 고체막 속에 주입 포획되는 형태로 배기된다. 스퍼터 이온펌프는 $10^{-5}$ Pa 부근에서 최대 배기속도를 가지며, 압력이 낮아질 수록, 특히 $10^{-10}$ Pa영역 이하에서는 그 배기속도가 급격히 저하되며, $10^{-10}$ Pa영역에서는 배기능력을 거의 상실한다. 따라서 스퍼터 이온펌프 단독으로 진공시스템을 배기할 때 도달압력은 $10^{-9}$ Pa 영역에 머무르게 되며, $10^{-10}$ Pa 이하의 극고진공을 얻기 위해서는, $10^{-8}$ Pa 이하의 압력에서 배기 속도가 압력과 무관한 흡착펌프(getter pump)와 이온펌프를 조합하여 사용한다. 본 실험에서는 $600^{\circ}C$ 이상의 온도로 진공로에서 탈개스시킨 진공용기를 배기속도 450, 60, 30, 20, 5, 3 l/s의 6종류의 이온펌프와 배기속도 400 l/s, 100 l/s의 non-evaporable getter (NEG) 펌프를 조합시켜 배기하여 그 배기 특성을 비교하였다. 도달 압력은 이온펌프의 배기속도가 클수록 낮아지는 경향을 보여주었다. 450 l/s 이온펌프와 400 l/s NEG를 조합하여 배기시킬 때 도달 압력은 ~$2{\times}10^{-10}$ Pa을 기록하여 가장 낮았으며, 3 l/s 이온펌프와 400 l/s NEG를 조합하였을 때는 $ 2{\sim}3{\times}10^{-8}$ Pa을 기록하였다. 450 l/s 이온펌프와 400 l/s NEG를 조합한 경우 잔류가스의 대부분이 수소였으나, 3 l/s 이온펌프와 400 l/s NEG의 조합한 경우에는 메탄의 잔류량이 수소 보다 많았다. 이 결과는 메탄을 배기하지 못하는 NEG의 배기 특성을 보완하기 위해서는 일정 배기속도 이상의 이온 펌프가 필요함을 보여준다.

• Membrane Journal
• /
• v.15 no.3
• /
• pp.198-205
• /
• 2005

Double-layered polymer films to assay the radioactive contamination were formulated using polysulfone (PSF) and cerium activated yttrium silicate (CAYS), consisting of a dense support layer and a CAYS-holding top layer prepared via the diffusion-induced phase inversion. As the vapor exposure process was omitted, the CAYS-holding layer showed a typical asymmetric structure, with CAYS being transfixed into the polymer network spread with large macropores. With the increase in vapor exposure time before immersion, morphology of the films transformed from asymmetric to sponge-like structures, with CAYS being localized in cellular structure. The border structure between the two layers reflects the phase inversion behavior of a cast solution during the coagulation. In the radioactive detection, the polymer phase in a film holding a sponge-like structure is so dense that the radionuclides, deposited on the film, could not filter through the phase, consequently resulting in the loss in the detection efficiency of the film.