• Journal of the Korean institute of surface engineering
• /
• v.52 no.6
• /
• pp.321-325
• /
• 2019

Triso-type coating layers of silicon carbide and graphite on UO₂ paticulate nuclear fuel were prepared by using fluidized bed type chemical vapor deposition and self-propagating high temperature synthesis methods to make a coated nuclear fuel of a power plant for hydrogen mass-production. The source and carrier gases were the mixture of methyltrichlorosilane and propane, and inert argon. Chemical analysis and microstructure observation showed that the coated layers were inner graphite, middle silicon carbide and outer graphite. The elastic modulus and nano-hardness of the silicon carbide layer were 503 [GPa] and 36 [GPa], respectively.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.4
• /
• pp.37-43
• /
• 2003

The exhaust gas recirculation (EGR) is needed for one of various strategies to reduce NOx emission. But to get the proper EGR rate, the intake and exhaust system become complicated, also application of EGR system is difficult because of the penalty in fuel consumption and the increase in particulate matter. This study is focused on the development of EGR valve using the electrical method. The effects of EGR on the characteristics of NOx, CO, CO2 emissions and particulate mater have been investigated using small-displacement size 0.8-liters engine of diesel passenger car operating at several loads and speeds. After the analysis and comparison between conventional E-EGR valve and developed E-EGR valve performance by test bench, the estimation of vehicle application was executed through the EGR map and CVS-75 test result measured on the chassis dynamometer.

• Tribology and Lubricants
• /
• v.16 no.5
• /
• pp.395-402
• /
• 2000

The effect of particulate contamination on friction and wear between a negative-pressure picoslider and a laser-textured disk was studied. Particles of different concentrations, materials and sizes were injected to the head-disk interface (HDI), consisting of disks with various textures, at the same speed. In a contaminated environment, durability of head-disk interface gradually decreased as the particle concentration increased. Large particles caused HDI failure early and resulted in an extensive damage to the slider and disk surfaces. Hard particles also caused HDI failure earlier and damages more extensive than soft ones. Based on the test results, mechanisms of HDI failure with picoslider were presented.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.05a
• /
• pp.167-170
• /
• 2005

This paper briefly reviews various existing methods to account for the effect of particle size on mechanical properties of particulate metal matrix composites. A simple and easy method is to use a size-dependent constitutive equation for the matrix. The suggested method does not require the development of a new computational algorithm and is compatible with any standard finite element software. Finite element analyses have been carried out to show how the deformation behavior of a metal matrix composite changes as the particle size and volume fraction are varied.

• Journal of the Korean Society for Precision Engineering
• /
• v.11 no.2
• /
• pp.95-103
• /
• 1994

The purpose of this paper is to provide the experimenters who use the oblique incidence ultrasonic method for anisotropic elastic constants measurement eith some useful relations. In particular, the equivalence of the times of flight by the energy ad phase velocities, which is key to the oblique incidence method, is proved explicitly. This equivalence greatly simplifies the analysis of immersion measurement results. In oredr to correctly measure the transit time of an immersed sample using the oblique incidence, the receiving transducer should be shifted laterally, and an expression in given for this shift. A method for determining all nine elastic constants of an orthotropic material is briefly described and the measurement results are listed for SiC particulate reinforced A1 matrix composites.

• 한국해양학회지
• /
• v.23 no.2
• /
• pp.76-88
• /
• 1988

Size distribution of suspended particulate materials (SPM) in the coastal waters of eastern Korea was studied using a laser particle size analyzer. Mean particle size (MPS) ranges from 3.69 to 8.40 ${\mu}m$ in surface waters, from 3.38 to 6.43 ${\mu}m$ in mid-depth waters, and from 3.88 to 8.30 ${\mu}m$ in near-bottom waters. For smaller MPS, the size distribution is unimodal, whereas it becomes polymodal as the MPS increases. Particle concentrations increased with the increases in MPS, suggesting that processes of adding larger particles in the waters such as resuspension of bottom sediments are more important in controlling MPS in the area than processes of removing smaller particles such as flocculation of fine particles. Observations of higher MPS near the coast in mid-depth waters, and at the continental slope in near-bottom waters appear to support the above idea. For surface waters with high MPS, mean particle density was noticably low, indicating the importance of biological activities in the formation of suspended particles.

• Applied Chemistry for Engineering
• /
• v.16 no.2
• /
• pp.194-199
• /
• 2005

The principle of vortex cyclone was applied to enhance the treatment efficiency of waste air streams containing particulate matters, phenol, and others. Adsorption, condensation, and/or coagulation could be induced at low temperature zone formed by Joule-Thomson expansion as the pressurized air and pulverized activated carbon were introduced at the tangential direction into the cyclone system applied with the coaxial funnel tube of vortex cyclone. Easily condensible vapors were adsorbed and/or condensed forcibly on coagulated or condensed materials which were formed as cores for coagulation or condensation by themselves or on pulverized activated carbons. These types of coagulation or condensation rates were rapidly promoted by increase in their diameter. The maximum removal efficiency obtained from this experiment for the removal of carbon dioxide and phenol was about 87.3 and 93.8 percent, respectively. Phenol removal efficiency was increased with the relative humidities and enhanced by pulverized activated carbon added. The Joule-Thomson coefficients were increased with the pressure of air injected in the range of the relative humidities between 10% and 50%. It is believed that the moisture, particulate matters, and the pressure of the process air introduced could control the removal efficiency of VOCs.

• Journal of Korean Society of Environmental Engineers
• /
• v.33 no.3
• /
• pp.196-201
• /
• 2011

Emission from meat cooking may contribute to the concentration of the Particulate Matters(PM) in the city. This study is to investigate the particle size and the emission characteristics of particulate matters from pork and beef cooking. The chamber was installed for sampling of PM generated from pork belly and beef sirloin cooking including seasoned ones. Cascade Impactor and Portable Aerosol Monitor (PAM) were used to analyse the particle size distribution. At the result of the Cascade Impactor sampling, particulate matters from the pork cooking was higher than that of beef. The gravimetric concentration of PM according to the size was highest at the range of $1.95{\sim}3.2{\mu}m$ and the gravimetric concentration of PM from the non-seasoned meat was higher than that of the seasoned one. The emission factors from pork, pork seasoned, beef and beef seasoned were 1.36 g/kg, 1.03 g/kg, 1.23 g/kg, 0.92 g/kg respectively. To see the result of PAM sampling, the ranges of $1.6{\sim}2.5{\mu}m$ and $2.5{\sim}3.5{\mu}m$ were reveled as highest. The ration of $PM_{2.5}/PM_{10}$ from pork and beef was 0.56~0.58. The emission factors from pork, pork seasoned, beef and beef seasoned measured by PAM were revealed as 3.37 g/kg, 2.76 g/kg, 2.93 g/kg, 2.77 g/kg respectively.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.9 no.3
• /
• pp.131-140
• /
• 2006

Suspended particulate matter and organic carbon were measured in the Mankyoung river estuary in February, May, July and August 2003. There was a large variance in river discharge between the dry season of February and May and the wet season of July and August. The influx of dissolved organic carbon into the estuary was $8.16{\times}10^2tonC\;month^{-1}$ in the dry season and $5.77{\times}10^3tonC\;month^{-1}$ in the wet season. The influx of particulate organic carbon was $9.37{\times}10^2tonC\;month^{-1}$ and $3.14{\times}10^4tonC\;month^{-1}$ in the dry and wet seasons, respectively. Especially, dissolved organic carbon in the northern part of the site inside the dike was increased in July when torrential rainfall was high. In the research, the distribution of dissolved organic carbon showed conservative behavior with the salinity gradient in the estuary, suggesting that physical mixing between seawater and freshwater dominates the distribution pattern of the dissolved organic carbon in the system. However 60 to 90% of the particulate organic carbon introduced into the estuary was removed from the surface water at the upper estuarine mixing zone of low salinities, showing non-conservative behavior similar with suspended particulate matte r. The completion of the Saemangum Dike is likely to inhibit the exchange of materials between open sea and the Mankyoung estuary. This suggests that the oxidation of organic carbon in the bottom of the estuary may exhaust dissolved oxygen in the confined environment.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.8 no.3
• /
• pp.148-157
• /
• 2005

In order to understand distribution characteristics and pollution of heavy metals in the artificial Lake Shihwa in the vicinity of Kyunggi Bay in relation with huge environmental changes, various environmental samples including seawaters, surface sediments and settling particulate matters were collected from Lake Shihwa in 2004. Due to extreme pollutant discharge from various anthropogenic sources such as the Banweol and Shihwa Industrial Complexes and cities, the highest metal concentrations in the samples such as waters, sediments and settling particulate matter were found in inner part of the lake. High metal contents (Cu, Zn and Hg) in sediments were observed at Sts. 2-4 and 9. The contents of Cr, Co, Ni, Cu, Zn and Pb in SPMs were high at St. 5 and low in the outer part of the lake. Spatial distribution of heavy metals were mainly controlled various biogeochemical factors and physical mixing as well as input of industrial and municipal wastewaters. Although tile environmental qualities of heavy metals in the lake have been improved partially due to inflow of outer seawater, it is not clear to reach a good environmental quality. Therefore, further environmental programs should be conducted continuously for environmental improvement.