• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.1
• /
• pp.171-175
• /
• 2006

In this paper, we have developed a retrodirective active array operating in the 2 GHz LS band. The retrodirective array has the property of redirecting any electromagnetic wave back to the incoming direction without any priory informations. The system is integrated with phase conjugators and antenna array. Microwave phase conjugators can be implemented by microwave mixers. In this research, 2-port gate mixers using pHEMT and $1{\times}4$ monopole array have been used to achieve the retrodirectivity. The measured results have been compared with the theoretical prediction, and it has been shown that there exists a reasonable agreement between them. The monopole array can be used easily in many areas for simplicity and cost-effective property, and the retrodirective array developed in this research can be applied directly in the base station facilities for the wireless mobile communications. indoor wireless LAN and RFID transponders.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.28 no.1
• /
• pp.63-69
• /
• 2015

In this paper, infrared reflector design targeting infrared stealth effect is presented using structural optimization based on the phase field method. The analysis model was determined to accomplish the design that an incident infrared wave was reflected to a desired direction. The design process was to maximize the objective value at the measuring domain located in a target region and the design objective was set to the Poynting vector value which represents the energy flux. Optimization results were obtained according to the variation of some parameter values related to the phase field method. The model with a maximum objective value was selected as the final optimal model. The optimal model was modified to eliminate the gray scale using the cut-off method and it confirmed improved performance. In addition, to check the desired effect in the middle wave infrared range(MWIR), the analysis was performed by changing the input wavelength. The finite element analysis and optimization process were performed by using the commercial package COMSOL combined with the Matlab programming.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.25 no.5
• /
• pp.362-367
• /
• 2005

Ultrasonic backward radiation profile is frequency-dependent when the incident region has deptional gradient of acoustical properties or multi-layers. Until now, we have measured the profiles of principal frequencies of an used transducers so that it was not easy to characterize the frequency dependence of the SAW(surface acoustic wave) from the backward radiation profile. We tried to measure the spectral backward radiation profiles using DFP(digital filer package) in a Lecroy DSO(digital storage oscilloscope). The measured spectral profiles showed that the steel specimen of #1200 surface treatment have 2% SAW velocity dispersion of the loaded case and the severly rusty steel specimen have the very big changes in the shape and pattern of the spectral profile. It is concluded that the spectral backward radiation profiles could be very effective tool to evaluate the frequency dependence of surface area.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.16 no.2
• /
• pp.83-91
• /
• 2004

The performance of wave control by a surface-mounted horizontal membrane is analyzed in the frame of linear potential theory. To employ the eigenfunction expansion method, the fluid domain is divided into two regions i.e. region without membrane and membrane-covered region. By matching the each solutions at boundaries of adjacent regions, the complete solution is obtained. The present analytical method solving the scattering problem directly gives the same results as Cho and Kim(1998)'s method solving the diffraction and the radiation problem separately. To verify the developed model, the model test with a surface-mounted horizontal membrane is conducted at the wave tank(36m${\times}$0.91m${\times}$l.22m). The analytic results are in good agreement with the experimental results. The reflection and transmission coefficients are investigated according to the change of membrane tension, length and incident frequencies.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.13 no.2
• /
• pp.91-98
• /
• 2010

The water elevation inside the air chamber and bi-directional air flow in the duct of Oscillating Water Column wave energy converter is one of the most important factors to evaluate the operating performance. The numerical wave tank based on the commercial software Fluent 6.2 in the present paper is employed to generate the incident waves. The numerical wave tank consists of the continuity equations, the Reynolds-averaged Navier-Stokes equations and the two-phase VOF function. The oscillating amplitude of water column in the chamber and bi-directional air flow in the duct installed on the top of the chamber are calculated, and compared with experimental data to verify the validation of the present NWT. The nozzle effects of the chamber-duct system on the relative amplitudes of the inner free water surface and air flow rate in the duct are investigated.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.23 no.1
• /
• pp.59-65
• /
• 2020

Many technologies are being studied to reduce the RCS(Radar Cross Section) of stealth aircraft. Most RCS-reduction technlogies correspond to platforms. It is important to identify factors that RCS performance through simulation analysis of aircraft Mounted equipment. In particular, there are no studies of RCS performance in the radar frequency band when antenna transmit signals are applied. In this paper, the RCS performance variation on the transmit signal on/off of antennas mounted on a stealth aircraft was verified. Antennas were selected for each frequency band and simulated analysis to the RCS performance changes during antenna transmitting signal. Finally, to verify the characteristics of the change in RCS performance, RCS test measurements on the low-profile antenna transmit signal on/off were performed. In addintion, antenna RCS test measurement was performed according to the change of transmit signal power output. As a result, it was confirmed that there is no change in RCS performance when an antenna transmit signal is applied.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.15 no.2
• /
• pp.111-117
• /
• 2012

Oscillating water column is the most widely used ocean energy converting systems all over the world. The operating performance is influenced by the efficiencies of the two converting stages in the OWC chamber-turbine integrated system. In order to consider the effects of the turbine, the orifice model are carried out. The VOF based Numerical Wave Tank (NWT) is utilized to simulate the water column oscillation inside the chamber and the results are compared with corresponding experimental data. This paper reviews the state of the art in interaction among wave elevation inside the chamber and air flow rate in the duct, which are considered the turbine effects. Effects of incident wave conditions and several shape parameters on the operating performance of OWC chamber are investigated numerically. The effects of the impulse turbine on the integrated system and interaction among the wave elevation, pressure and air flow velocities variations are investigated.

• Tunnel and Underground Space
• /
• v.21 no.2
• /
• pp.109-116
• /
• 2011

In this study, we estimated the dynamic tensile strength and strain rate from Brazilian tensile test using Split Hopkinson Pressure Bar (SHPB) system. A pulse shaping technique, which controls the shape of the impactinduce incident waves, was used for achieving the dynamic stress equilibrium and constant strain rate before fracture of rock samples. Three kinds of rock type, Inada granite, Kimachi sandstone and Tage tuff were prepared as 50mm in diameter and 26 mm in thickness. The high-speed videography system was used to observe the fracture processes of the rock samples. As the results of the tests, the ratio of dynamic tensile strength and static tensile strength was 11.9 for Inada granite, 8.5 for Kimachi sandstone and 9.2 for Tage tuff.

• The Journal of the Acoustical Society of Korea
• /
• v.23 no.5
• /
• pp.362-369
• /
• 2004

The High-frequency (30 ∼ 120 ㎑) bottom reflection loss at rough water-sediment interface is affected by the gram size distribution of the sediments. The roughness of the bottom surface is represented by "acoustical roughness. g/sub R/" The grain size of sandy sediments is g/sub R/∼O(1) and the dependence as a function of frequency. We suggest the modified bottom reflection loss model (HYBRL model , HanYang university Bottom Reflection Loss model) that include in the deviation of the reflection loss as a function of the grain size distribution and frequency dependence. And bottom reflection loss model of frequency dependence and deviation of bottom properties is verified by water tank and field experiments.

• Journal of the Society of Naval Architects of Korea
• /
• v.45 no.1
• /
• pp.29-41
• /
• 2008

The present paper provides a CFD analysis of diffraction problem for a ship with forward speed using an unsteady RANS simulation method, a WAVIS code. The WAVIS viscous solver adopting a finite volume method has second order accuracy in time and field discretizaions for the RANS equations. A two phase level-set method and a realizable ${\kappa}-{\varepsilon}$ turbulence model are adopted to compute the free surface and to meet the turbulence closure, respectively. To validate the capability of the present numerical methods for the simulation of an unsteady progressive regular wave, computations are performed for three grid sets with refinement ratio of ${\sqrt{2}}$. The main simulation is performed for a DTMB5512 model with a forward speed in a regular head sea condition. Validation of the present numerical method is carried out by comparing the present CFD results with available unsteady experimental data published in the 2005 Tokyo CFD Workshop: resistance, heave force, pitch moment, unsteady free surface elevations and velocity fields.