• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.11 no.4
• /
• pp.201-215
• /
• 1999

Field measurements were made for long- and short-period waves and current velocities at the harbor mouth using pressure-type wave gauges and a current meter, respectively, at the Gamcheon Harbor which has a rectangular shape with a narrow entrance. The measured pressure data were subjected to spectral analyses after removing tidal effects by applying trend removal and high-pass filtering. For the band averaging of the raw spectra, in order to obtain good resolution over the entire frequency, instead of a constant band width, variable band widths were used, which gradually increase as marching from the lowest frequency towards higher frequencies. The Helmholtz resonance mode at the Gamcheon Harbor shows the relative amplification ratio of 9.2 at the wave period of 31.7 minutes, which is quite large compared with those at the harbors located on the east coast of Korea. The second and the third resonance period was 10.3 and 5.4 minute, respectively. On the other hand, the analysis of every 24 hours data shows that during storms the spectral densities are very large compared to those during calm seas and also the second and third resonances are predominant.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.30 no.5
• /
• pp.759-770
• /
• 1997

The general flow patterns in the Cheju Strait have been investicated by analyzing the current observations measured in $1986\~1989$ by current meter mooring in 3 north-south sections in the Cheju Strait and at 4 observation points around Cheju Harbour, and measured in $1981\~1987$ by drogue tracking. 1. In the Cheju Strait, there are eastward or northeastward residual currents, which implies that sea waters flow into through the whole western section and flow out through the whole eastern section in the Cheju Strait. The velocity of residual currents are $5.2\~30\;cm/sec$ in 10 m layer and $1.3\~24cm/sec$ in mid-bottom layer. Generally, the flow is strong along the deepest through and the northern part, and weak in the shallow areas near Chuja Islands and Bogil Island. 2. In the western entrance of the Cheju Strait, the observed mean residual velocity is 6.93 cm/sec and the volume transport is 0.384 Sv. There are a big discrepancy between the observed residual currents and the geostrophic currents. 3. Near the frontal areas northwest to Chuja Islands, warm and saline offshore waters, flow northward about 5 miles into the southern coastal areas of the Korean Peninsula in flood, and flow back rather eastward or southeastward than southward in ebb. So, warm and saline waters flow along coastal areas, being mixed with coastal waters. As a result, the northwestern area of Chuja Islands plays a role of the entrance of influx of warm and saline offshore water to the southwestern coastal areas of the Korean Peninsula. It should be stressed that this flow pattern is not due to the residual flows, but to the temporal (tidal) flows.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2023.05a
• /
• pp.132-132
• /
• 2023

본 연구에서는 식생대 퇴적과 침식, 하안침식을 고려한 식생대의 발달과정을 실내실험을 수행하여 정량적으로 분석하고 하도의 지형변화를 해석하는데 중요한 결과를 도출하였다. 식생대 입구와 중류부에서 식생대 좌완과 우안으로 흐름이 집중되며, 유속이 빠르다. 식생대와 식생이 없는 좌안과 우안의 유속차에 의하여 전단층이 형성되고 조직와가 발생하였다. 식생하도의 지형변화는 초기에 하안침식이 발생하고, 하폭이 증가하면 상류 유입구에서 중앙사주가 발달하였다. 시간이 증가하면서 사주는 하류로 이동하였다. 식생대에서 흐름이 분리되면서, 좌안와 우안에서수충부가 형성되고 하안이 침식되었다. 식생대 전면부에서 유사가 퇴적되며, 후면부에서 침식이 발생하였다. 식생밀도가 증가하면서 퇴적량은 증가하지만, 한계 이상으로 증가하면 퇴적량은 감소하였다. 수치모의 결과, 식생의 밀도가 증가함에 따라, 식생대 전면부에서 유사가 퇴적이 되고, 사주가 상류로 성장하면서 하안침식이 발생하였다. 또한 식생대에 의해 유사가 포착되면서, 식생대 후미에서 하상이 침식되었다. 식생대의 밀도가 증가하면서, 식생대 후미에서 침식이 발생하는 지점은 상류로 전파되었다. 식생대에 의해 발달한 사주는 실내실험에서 식생대 하류에서 성장하지만, 수치모의 결과는 식생대 상류에서 성장하는 특성을 보여주었다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.5
• /
• pp.1774-1780
• /
• 1991

본 연구에서는 유한 길이를 갖는 수직 덕트내 공기 유동의 속도 분포를 LDV를 사용하여 측정하며 유동 특성에 미치는 가열정도, 덕트간격 및 입구소도등의 영향을 보고하고자 한다. 또한 속도분포, 온도분포 및 열전달에 미치는 부력의 영향을 수치 적으로 예측하여 그 타당성을 검증하고자 한다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.6
• /
• pp.71-75
• /
• 2005

An experimental study was carried out to investigate the effect of film cooling in the lab-scale dump-cooled liquid rocket engine using LOX and kerosene as propellants. The nozzle of the rocket engine was film cooled with water as coolant. A special film cooling adapter was fabricated to introduce the film-coolant into the thrust chamber. The flow rates of film coolant was approximately 15~19 percent of the total propellant. The nozzle heat flux was determined from the measured temperature rise and flow rate of the coolant(water). Large reductions in the nozzle heat flux was resulted when film cooling adapter located directly upstream of the nozzle.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.10 no.3
• /
• pp.90-98
• /
• 2006

The Heated Tube Facility(HIF) was fabricated to identify the forced convective heat transfer and the cooling characteristic for the hydrocarbon fuel(Jet A-1), which is used for the coolant of the regenerative cooling system. The forced convective heat transfer coefficient was calculated from the measured coolant and tube surface temperature. In case of using the Jet A-1, the maximum heat flux which the coolant can absorb was identified by determining the critical wall temperature generating the burnout on the fixed flow condition. The inlet bulk-temperature of the coolant has a direct influence on the forced convective heat transfer characteristic.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.381.1-381.1
• /
• 2016

분석 방법의 간편함과 용이함의 장점은 물론, 시료 전처리 과정이 적어 시료물질의 임의 파괴나 훼손을 방지한다는 이유에서 최근 10년 간 많은 연구가 이루어지고 있는 대기압 질량분석 기술은 기압차이가 없는 대기압 분위기에서 질량분석이 이루어지기 때문에 시료를 질량분석기 입구 바로 앞에 스테이지를 설치하고서 시료를 이온화하는 경우가 대부분이다. 이 때문에 균질하지 않은 시료의 관심 영역을 모니터링하면서 질량분석을 하기에는 어려움이 있으며, 공간 정보를 추가한 질량분석 이미징에 한계가 있었다. 이에 본 연구팀은 질량분석기 입구에 챔버와 보조 펌프를 장착하여 강제로 기체 흐름 일으켜 시료로부터 발생한 이온을 질량분석기 입구로 유도하여, 원거리에서 시료를 이온화해도 질량분석기 입구까지 이온을 성공적으로 전달시키는 방법을 제안한다. 이를 이용하면 분석하고자 하는 시료를 현미경 스테이지 위에 위치시켜 분석하고자하는 부분을 현미경으로 확인하면서 질량분석을 할 수 있으며, 나아가 대기압 질량 분석 이미징 기술을 구현할 수 있다. 대기압 탈착/이온화원은시료에 열적 손상이 없는 조건으로 시편의 이온화 및 탈착 과정이 이루어지게 하기 위해 저온 대기압 헬륨 플라즈마 젯과 펨토초 레이저를 결합하여 대기압 이온화원을 제작하였다. 이온 전달관은 1/4" (6.35 mm) 외경의 60 cm 길이의 스테인리스 스틸관을 사용하여 질량분석기에서 약 60 cm 떨어진 현미경 위의 시료의 질량분석이 가능하게 했다. 보조 펌프의 계기압과 저온 대기압 헬륨 플라즈마 젯의 헬륨 기체의 유속을 변화시키면서 시료인 PDMS (polydimethylsiloxane) 의 질량 스펙트럼 (m/z 270.314) 세기를 관찰하여 최적의 이온 전달 조건을 찾았다. 추가로 현미경 스테이지에 정밀 2-D 자동 스캐닝 스테이지를 장착하여 질량분석 정보에 공간 정보를 더할 수 있는 질량분석 이미징 기술 방법을 개발하여 생체 시편의 질량분석 이미징을 얻었다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.4
• /
• pp.639-647
• /
• 2019

Recently, as the semiconductor integration technology due to miniaturization and high density of electronic equipment have developed, it is importantly recognized the application of thermal control system in order to release inner heat generated from chips, modules, In this study, we considered the heat transfer and pressure drop characteristics in a horizontal channel with four blocks using k-${\omega}$ SST turbulence model During CFD (Computational Fluid Dynamics) analysis, the parameters applied block width, block height, heat source and turbulence generator placement etc. As the boundary conditions of analysis, the channel inlet temperature and flow velocity were respectively 300 K and 3.84 m/s, the heat flux was $358W/m^2$. As a result, the heat transfer performance was decreased as the block width ratio (w/h) was increased, while it was increased as the block height ratio (h/w) was increased. In addition, as the arrangement of heat source size was increased to high heat flux from low heat flux, it was influenced by heat source size and the heat transfer coefficient showed a tendency to increase, When the turbulence generator was installed in the upper part of block No. 1 position the closely to the channel entrance, the heat transfer characteristics was greatly influenced on the whole of four heating blocks. and in oder to consider the pressure drop characteristics, we are able to select the most appropriate turbulence generator's position.

• Journal of Korea Water Resources Association
• /
• v.46 no.6
• /
• pp.629-642
• /
• 2013

In this study, the efficiency of the by-pass fishway installed at Kangjung-Goryong Weir in Nakdong River was assessed by using River2D which is a two-dimensional physical habitat simulation model. The model was calibrated and validated through the measured water elevation. The assessment was performed according to flow condition such as flood, normal, and low flow. Especially the low flow condition was focused on because the target fish, Zacco Platypus, have moved frequently up and downstream at the spawning season from April to June. From simulation results, it can be deduced that the influx efficiency and the passage efficiency of the fishway in the low flow is higher than that in the flood and normal flow due to occurrence of proper velocity at fishway entrance.

• 한국해양학회지
• /
• v.29 no.2
• /
• pp.95-106
• /
• 1994

Tidal and wind-driven currents in Chinhae Bay are investigated using a three-dimensional numerical model developed by Kim et al. (1993). The simulations indicate that the flow patterns in the bay are predominated by the bathymetry, wind and river inflow, and the effects of wind on the flow pattern in the inner bay are much stronger than those in the entrance channel. Computed tidal currents coincide with the field measurements. The horizontal and vertical velocities of tidal and residual currents are strong in the entrance channel of the bay, whereas the velocities are relatively weak in the western and northern parts of the bay. Computed velocity fields show the expected phase difference between the velocities in the surface and those in the bottom layer, and these characteristics are more remarkable during the spring tide than the neap tide. The surface currents in the bay depend strongly on the wind and river inflow, and such phenomena are more remarkable during the neap tide than the spring tide.