• Journal of the Korean Magnetics Society
• /
• v.7 no.1
• /
• pp.49-54
• /
• 1997

The effect of Co and annealing temperature on the magnetic properties, phase change and microstructure of melt-spun $(Nd_{14.73}Fe_{78.67}B_{6.60})_{100-x}Co_x$ (X=0, 1, 2, 3) ribbons has been studied. The Co containing ribbons were found to have higher coercivity ($_iH_c$) than the ribbons without Co. Intrinsic coercivity of 20.3 kOe has been obtained by addition of 2 at%Co. This effect by Co addition is also represented in the case of hot pressed and die-upseted magnets. The maximum intrinsic coercivities of hot press and die-upset $(Nd_{14.73}Fe_{78.67}B_{6.60})_{100- x}Co_x$ (X=0, 1, 2, 3) magnets are 16.9 kOe and 15.2 kOe when X=2.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.21 no.4
• /
• pp.415-424
• /
• 2001

The destructive method is reliable and widely used for the estimation of material degradation but, it have time-consuming and a great difficulty in preparing specimens from in-service industrial facilities. Therefore, the estimation of degraded structural materials by nondestructive evaluation is strongly desired. In this paper, the use of guided wave was suggested for the evaluation on thermally damaged 2.25Cr-1Mo steel as an alternative way to compensate for limitations of fracture tests. The observation of microstructure variations of the material including carbide precipitation increase and spheroidization near grain boundary was conducted and the correlation with the guided wave features such as energy loss ration and group velocity changes was investigated. Through this study, the feasibility of ultrasonic guided wave evaluation for thermally damaged materials was explored.

• Korean Journal of Materials Research
• /
• v.5 no.8
• /
• pp.1026-1034
• /
• 1995

It is well known that the addition of CaO-SiO$_2$to Mn-Zn ferrites forms an insulating grain bounary layer with high electrical resistivity. This study investigated the effect of Nb$_2$O$_{5}$ on the electromagnetic properties of high frequency low loss Mn-Zn ferrites. The addition of 300ppm Nb$_2$O$_{5}$ developed an exaggerated grain growth while the addition of CaO-SiO$_2$addition with 200ppm Nb$_2$O$_{5}$ more effectively increased the density than that without Nb$_2$O$_{5}$. The addition of Nb$_2$O$_{5}$ showed the lower power loss below 100 ppm SiO$_2$and the Nb$_2$O$_{5}$-CaO addition lowered the power loss at higher sintering temperature.

• Korean Journal of Materials Research
• /
• v.5 no.8
• /
• pp.1005-1112
• /
• 1995

The Effects of 0~9% stretching on the microstructure and mechanical properties have been investigated in Al-Li-Cu-Mg alloys. Stretching made T$_1$(Al$_2$CuLi) precipitates finer and more uniform, however, had no effect on the size of $\delta$'. The number of sheared $\delta$'precipitates distributed in the matrix were reduced. The 6% stretching improved the yield strength of the alloys aged at 15$0^{\circ}C$ for 120 hours from 328~342 MPa to 466~488MPa, however, decreased the elongation from 9.7~10.4% to 5.7%.

• Analytical Science and Technology
• /
• v.6 no.2
• /
• pp.197-205
• /
• 1993

Blends of elemental Ni and 20 weight % Cr powder were milled for different period in a laboratory attritor. Powder size distribution, microstructure and X-ray diffraction characteristics were investigated as a function of processing period. Saturated magnetization, Ms and coercive force, Hc we also measured and compared with plasma melted ingot to confirm the mechanically alloyed states. Mechanical alloying occurred as a consequence of the partition of powders and the increase of interfacial area driving diffusing of Cr into Ni. However, magnetic properties of chemically homogeneous solid solution like melted ingot has not been observed even though steady state of submicron grain size has been achieved after milling over 15 hrs. Further mechanical alloying period gave refinement of grain size, which resulted in the increase of alloyed layer. It is concluded that homogenization should be controlled by the increase of interfacial area between constitutive powders caused by plastic particle deformation and by the diffusion of Cr within the alloyed phase into Ni-rich phase through lattice defects.

• Applied Chemistry for Engineering
• /
• v.8 no.6
• /
• pp.1000-1005
• /
• 1997

The properties of ceramics by solid-state reaction with hydroxyapatite[$Ca_{10}(PO_4)_6(OH)_2$], which was isolated from tuna bone by wet milling process were investigated. The bulk density $2.93g/cm^3$ at $1350^{\circ}C$ was close to the calculated density $3.21g/cm^3$. On X-ray measurements, the major phases were identified as hydroxyapatite at below $1300^{\circ}C$, but the whitlockite [$Ca_3(PO_4)_2$] phases were appeared due to a decomposition of hydroxyapatite with temperature. The microstructures of sintering specimens were shown as small closed pores between grain boundaries. The mean bending strength of the sintered hydroxyapatite by solid-state reaction is about 58 MPa and this value is higher than that of the articular cartilage maximum strength, 40MPa.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.111-111
• /
• 2018

ASTM A387-Gr.91 강은 우수한 고온 강도, 크리이프 저항성 그리고 내산화성 등으로 인해 화력 및 바이오매스 발전 시설과 같은 고온 설비의 구조재료로 널리 사용되고 있다. 고온 환경에서 높은 강도는 탄화물과 탄질화물에 의한 석출강화가 주 요인으로 작용한다. 열처리 과정에서 Mo, Cr, Mn, 그리고 Fe는 구-오스테나이트 및 마르텐사이트 라스 입계에 $M_{23}C_6$ 탄화물로 석출되며, V, Nb, 및 N은 조직 내부에 미세한 MX 탄질화물로 석출된다. 따라서 합금의 고온 강도는 조직 내 석출물의 개수밀도와 크기에 크게 의존한다. 그러나 적용 환경의 특성 상 고온 노출에 따른 2차상 석출 및 조대화의 조직열화 현상이 발생하며, 이는 재료의 강도를 저하시킨다. 본 연구에서는 ASTM A387-Gr.91 강의 미세조직 열화에 따른 강도저하 및 파괴 양상을 고찰하는데 그 목적을 두었다. 본 연구에서 사용된 ASTM A387-Gr.91 강의 화학성분(wt, %)은 0.1 C, 0.38 Si, 0.46 Mn, 0.25 Ni, 8.38 Cr, 0.93 Mo, 0.18 V, 0.09 Nb, 그리고 나머지는 Fe 이다. 조직열화 및 기계적 강도저하 특성을 평가하기 위한 등온열화는 $650^{\circ}C$의 대기 환경에서 최대 1000시간동안 실시하였다. 열화된 시험편의 미세조직 및 탄화물에 대한 분석은 SEM과 EDS를 이용하여 실시하였다. 그리고 기계적 강도 평가는 인장실험과 비커스 경도시험을 통해 실시하였다. 또한 열화 시간에 따른 파단양상의 변화를 관찰하기 위해 인장시험편의 파단면을 SEM과 EDS를 이용하여 분석하였다. 그 결과, 열화에 따른 마르텐사이트 라스의 소실, 탄화물의 조대화, 그리고 2차상 석출의 조직 열화현상이 나타났다. 또한 기계적 강도는 조직 열화에 따라 저하되는 경향을 나타냈다.

• Journal of the Korean Ceramic Society
• /
• v.39 no.7
• /
• pp.635-641
• /
• 2002

Electrical conduction of $SrZrO_3$ doped with $Y_2O_3$ was measured as a function of gas atmosphere and temperature by impedance spectroscopy. Hydrogen dissolution, due to an enhanced driving force in the presence of oxygen, results in protonation by water incorporation. Proton conductivity increased with water vapor pressure, ${P_w}^{1/2}$. In the pure hydrogen atmosphere, the dissolution of hydrogen,$H_2(g)=2H_{i}$ +2e', is supposed to be driven by a reduced activity of electrons, ascribable to their trapping in oxygen vacancies. The activation energy of electrical conductivity was 50 kJ/mol, in wet argon atmosphere in the temperature range of $600~900^{\circ}C$, similar to those reported for proton conduction in the literature. Grain boundary effect in proton conduction was substantial in the 10% doped case at temperatures lower than $700^{\circ}C$.

• Journal of the Korean Ceramic Society
• /
• v.37 no.10
• /
• pp.968-974
• /
• 2000

Nb$_2$O$_{5}$와 MnO 첨가에 따른 Pb$_{0.6}$Sr$_{0.4}$TiO$_3$반도체 세라믹의 미세구조와 전기적 특성은 유전특성, I(current)-V(voltage) 측정, 그리고 복소 임피던스 측정 등을 이용하여 고찰하였다. Nb 도핑량이 0.4 mol% 이하인 경우 Nb 도핑량에 따라 전도성과 입성장은 증가되었으나 그 이상의 도핑량에서는 Sr이나 Pb 공공의 생성으로 인하여 전도성이 감소되고 입성장도 억제되는 것을 관찰할 수 있었다. 0.4 mol% Nb-doped Pb$_{0.6}$Sr$_{0.4}$TiO$_3$에 0.01 mol% MnO를 첨가한 경우 비저항비($ ho$$_{max}$/$\rho$/min/)가 $10^2$에서 $10^4$으로 크게 향상되었다. 그리고 전이 온도 주변에서 여러 개의 변곡점을 지니는 비옴성 거동이 발견되었다. 이와 같은 현상은 입계에 존재하는 Mn 이온이 부분적으로 편석되어 표면 전하의 보상 효과에 영향을 미치는 것이라고 사료된다.

• Journal of the Korean Ceramic Society
• /
• v.34 no.8
• /
• pp.803-810
• /
• 1997

Ba0.5Sr0.5TiO3 thin films were deposited by RF magnetron sputliring method in order to clarify the anneal condition and doping effect on loakage current Nb and Al were selected as electron donor and acceptor dopants respectively, in the BST films because they have been known to have nearly same ionic radii as Ti and thought to substitute Ti sites to influence the charge carrier and the acceptor state adjacent to the gram boundary. BST thin films prepared in-situ at elevated temperature showed selatively high leakage current density and low breakdown voltage. In order to achieve smooth surface and to improve electrical properties, BST thin films were deposited at room temperature and annealed at elevated temperature. Post-annealed BST thin films showed smoother surface morphology and lower leakage current density than in-situ prepared thin films. The leakage current density of Al doped thin films was measured to be around 10-8A/cm2, which is much lower than those of undoped and Nb doped BST films. The result clearly demonstrates that higher Schottky barrier and lower mobile charge carrier concentration achieved by annealing in the oxygen atmosphere and by Al doping are desirable for reducing leakage current density in BST thin films.