• Journal of Korean Tunnelling and Underground Space Association
• /
• v.20 no.6
• /
• pp.1125-1146
• /
• 2018

Segment lining applied to the TBM tunnel is mainly made of concrete, and it requires sufficient structural capacity to resist loads received during the construction and also after the completion. When segment lining is design to the Limit State Design, both Ultimate Limit State (ULS) and Service Limit State (SLS) should be met for the possible load cases that covers both permanent and temporary load cases - such as load applied by TBM. When design segment lining, it is important to check structural capacity at the joints as both temporary and permanent loads are always transferred through the segment joints, and sometimes the load applied to the joint is high enough to damage the segment - so called bursting failure. According to the various design guides from UK (PAS 8810, 2016), compression stress at the joint surface can generate bursting failure of the segment. This is normally from the TBM's jacking force applied at the circumferential joint, and the lining's hoop thrust generated from the permanent loads applied at the radial joint. Therefore, precast concrete segment lining's joints shall be designed to have sufficient structural capacity to resist bursting stresses generated by the TBM's jacking force and by the hoop thrust. In this study, bursting stress at the segment joints are calculated, and the joint's structural capacity was assessed using Leonhardt (1964) and FEM analysis for three different design cases. For those three analysis cases, hoop thrust at the radial joint was calculated with the application of the most widely used limit state design codes Eurocode and AASHTO LRFD (2017). For the circumferential joints bursting design, an assumed TBM jack force was used with considering of the construction tolerance of the segments and the eccentricity of the jack's position. The analysis results show reinforcement is needed as joint bursting stresses exceeds the allowable tensile strength of concrete. This highlights that joint bursting check shall be considered as a mandatory design item in the limit state design of the segment lining.

• Journal of the Korean Geotechnical Society
• /
• v.27 no.6
• /
• pp.17-26
• /
• 2011

Ground anchor method is one of the most popular reinforcing technology in Korea. For the sound monitoring of slope reinforced by permanent anchor for a long period, monitoring the tension force of ground anchor is very important. However, special technology except conventional load cell has not been developed for this purpose. In this paper, a new method is described to replace the conventional strain gauge and V.W. type load cell which has been commonly used as a prestress force monitoring tool for a short-term and long-term. Four 11.5 m long strain detectable tension type anchors were made using FBG sensor embedded tendon since FBG sensor is smaller than strain gauge type load cell and does not have noise from electromagnetic wave. Each two set strain detectable tension type anchors were installed into the different ground conditions, i.e., soft rock and weathered granite soil. Prestress force of ground anchor was monitored during the loading-unloading step from in-situ pullout test using proposed FBG sensor embedded in the tendon and the conventional load cell Test results show that the prestress force monitored from FBG sensor may well be used practically, for it almost matches with that measured from expensive load cell.

• The Journal of Engineering Geology
• /
• v.13 no.4
• /
• pp.429-444
• /
• 2003

Domestic marbles are mostly distributed in Gyeonggi and Yeongnam Massifs, southwest and northeast Ogcheon Belts, which belong to Precambrian, age-unknown, Cambrian-Ordovician ages, respectively. The former marbles occur as interbedded rocks in metasediments and xenoliths in granitic gneisses. Age-unknown ones occur as interbedded in the formations of Hyangsanri, Gyeomyeongsan, Hwajeonri and Munjuri, and some in metasedimentary rocks. The latter ones occur as interbedded in Pungchon Limestone, and in Jeongseon Limestone, Hwacheonri Formation and Great Limestone Group, respectively. Among physical properties, porosity shows irregular patterns to density and compressive strength, respectively. Absorption ratio has a linear pattern of positive trend to porosity, and compressive strength mostly shows a positive trend to tensile strength. Compressive strengths of the marbles are as follows : Precambrian $1,106{\;}kg/\textrm{cm}^2$, age-unknown $935{\;}kg/\textrm{cm}^2$. Cambrian $1,162{\;}kg/\textrm{cm}^2$ and Ordovician $1,560{\;}kg/\textrm{cm}^2$, respectively. Tensile strengths have decreasing trends as the above order of geologic age. In diagrams of major elements, $Al_2O_3,{\;}Fe_2O_{3(t)}{\;}and{\;}Na_2O+K_2O$ generally show positive trends with increasing $v_2$. MgO/CaO of Precambrian and age-unknown marbles have much higher values than Cambrian and Ordovician marbles as follows, Precambrian 0.31, age-unknown 0.30, Cambrian 0.03 and Ordovician 0.08. And MgO shows a negative trend with increasing CaO, which nay be caused by dolomitization. By MgO contents they can be classified into calcitic dolomite, dolomitic limestone, limestone and dolomitic limestone, respectively.

• Korean journal of food and cookery science
• /
• v.16 no.6
• /
• pp.593-601
• /
• 2000

Seven domestic wheat cultivars, Suwon 261, Suwon 265, Eunpa, Kobun, Alchan, Olgru, and Kumgang, and a standard wheat, ASW(Australian Standard White Wheat), were compared in noodle-making properties. The ash contents of domestic wheats and flours were 0.1-0.3% higher than that of ASW. Therefore, domestic wheats required the control of ash contents during milling process. The protein contents which suggest the flour gluten content were 10.32, 11.3, and 9.57% in Suwon 261, Suwon 265, and Kumgang cultivars, respectively. Valorimeter values of Eunpa, Olgru, and Kumgang which indicate the dough formation time and stability were similar to that of ASW. Resistance rate of domestic wheats was lower than that of ASW. Maximum viscosity in Amylograph for Eunpa, Olgru, and Kumgang were in the range of 500-800BU, which were suitable for making noodles. Increase in weight and volume of Olgru noodle was negatively correlated with protein content. Turbidity was not positively correlated with weight and volume increase, but domestic cultivars except Suwon 265 and Eunpa showed a similar turbidity with ASW. The mechanical properties of wet and dry noodles were evaluated by TPA test before and after cooking. Springiness and cohesiveness of wet noodles increased by cooking, and the domestic cultivars showed higher values than ASW. Springiness and cohesiveness of dry noodle were not increased by cooking in any cultivars. Gumminess, chewiness and hardness of domestic wheat cultivars showed higher values than that of ASW. In the tensile test, wet noodles showed no difference between domestic cultivars and ASW. But dry noodles of domestic wheat cultivars showed higher values than ASW. In the color test for lightness, redness and yellowness, there were no differences between flour and dough of domestic wheat cultivars and ASW. In the sensory evaluation, Kumgang wheat cultivar was the most preferred among the wet and dry noodles of other domestic wheat cultivars and ASW. These results suggested Kumgang wheat cultivar to be a practical wheat variety for noodle-making.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.18 no.3
• /
• pp.172-180
• /
• 1998

It is attempted to verify the Quantitative relationship between fracture mechanical parameters (${\Delta}K$, $K_{max}$) and X-ray parameters (residual stress, half-value breadth) of A12009-15v/o $SiC_w$ composite, and normalized SS41 steel. In this study, fatigue crack propagation test were carried out and X-ray diffraction was applied to fatigue fractured surface in order to investigate the change of residual stress and half-value breadth on fatigue fractured surface. And it is loaded prestrain to each tensile specimen, A12009-15v/o $SiC_w$ composite(0.3, 0.5, 1, 1.5, 2%) and normalized SS41 steel(0.63, 2.25, 7.50, 13.7, 20%), for investigating plastic strain rate using nondestructive measurement method. X-ray diffraction was applied to the prestrained tensile specimens in order to measure the change of residual stress and half-value breadth.

• The Journal of Korean Academy of Prosthodontics
• /
• v.48 no.1
• /
• pp.61-68
• /
• 2010

Purpose: This article attempted to determine the factors affecting the preload and screw loosening. Methods: Available clinical studies from 1981 to 2008 from the PUBMED that presented screw loosening data and review articles regarding screw joint stability were evaluated. Eleven studies dealing the biomechanical principles of the screw mechanics were reviewed. Moreover, the results of our data were included. Results: The frequency of screw loosening was consequently reduced due to the advancement in torque tightening with torque wrench, screw material, coating technique for reducing the frictional force, and thread design, etc. If preload in the screw falls below a critical level, joint stability may be compromised, and the screw joint may fail clinically. The types of fatigue failure of screw were divided to adhesive wear, plastic deformation, and screw fracture. Conclusion: An optimum preload is essential to the success of the implant-abutment complex. To maintain optimum preload, using a torque wrench and re-tightening at recall time were needed.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.20 no.1
• /
• pp.49-59
• /
• 1984

Optimizing investigation of characteristics of underwater welding by a gravity type arc welding process was experimentally carried out by using six types of domestic coated welding electrodes for welding of domestic marine structural steel plates (KR Grade A-1, SWS41A, SWS41B,) in order to develop the underwater welding techniques in practical use. Main results obtained are summarized as follows: 1. The absorption speed of the coating of domestic coated lime titania type welding-electrode became constant at about 60 minutes in water and it was about 0.18%/min during initial 8 minutes of absorption time. 2. Thus, the immediate welding electrode could be used in underwater welding for such a short time in comparison with the joint strength of in-atmosphere-and on-water-welding by dry-, wet-or immediate-welding-electrode. 3. By bead appearance and X-ray inspection, ilmenite, limetitania and high titanium oxide types of electrodes were found better for underwater-welding of 10 mm KR Grade A-1 steel plates, while proper welding angle, current and electrode diameter were 6$0^{\circ}C$, above 160A and 4mm respectively under 28cm/min of welding speed. 4. The weld metal tensile strength or proof stress of underwater-welded-joints has a quadratic relationship with the heat input, and the optimal heat input zone is about 13 to 15KJ/cm for 10mm SWS41A steel plates, resulting from consideration upon both joint efficiency of above-100% and recovery of impact strength and strain. Meanwhile, the optimal heat input zone resulting from tension-tension fatigue limit above the base metal's of SWS41A plates is 16 to 19KJ/cm. Reliability of all the empirical equations reveals 95% confidence level. 6. The microstructure of the underwater welds of SES41A welded in such a zone has no weld defects such as hydrogen brittleness with supreme high hardness, since the HAZ-bond boundary area adjacent to both surface and base metal has only Hv400 max with the microstructure of fine martensite, bainite, pearlite and small amount of ferrite.

• Applied Chemistry for Engineering
• /
• v.5 no.5
• /
• pp.764-771
• /
• 1994

Electrochemical synthesis of conductive polypyrrole films was carried out in nucleophilic solvent containing p-toluenesulfonic acid or bezensulfonic acid as supporting electrolyte and dopant. Also characteristics of degradation and improvement of mechanical properties were studied. The conductivity, tensile strength and elongation of the films obtained in dimethyformamide/p-toluenesulfonic acid had the highest value of 10-40S/cm, $25N/mm^2$ and 10%, respectively. The optimum condition of electrochemical synthesis was $2mA/cm^2$ for constant current method and 0.9V for constant potential method containing 0.5M pyrrole and 0.5M p-TSA. The obtained films showed good stability in air and electrode characteristics of secondary battery by reversibility in doping and undoping. The degradation process was 1st order reaction at various temeprature. The activation energy and rate constant of degradation reaction were $1.01JK^{-1}mol^{-1}$ and $3.1{\times}10^{-7}min^{-1}$ respectively at $25^{\circ}C$. For the improvement of mechanical properties, composition of polypyrrole films with various host polymer were investigated and increase of tensile strength and elongation was confirmed.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2001.04a
• /
• pp.34-34
• /
• 2001

열CVD법에 의하여 아세틸렌 가스를 탄소 원으로 사용한 탄소 나노튜브의 성장거동을 조사하였다. 닉켈 분말의 직경을 15nm 내지 90nm 범위로 조정하여 기판 에 촉매로 배열하였다. 탄소 나노튜브는 질소, 수소, 알곤, 암모니아 등 여러가지의 가스 분위기에서 증착되었으며 이들 가스의 혼합 분위기가 탄소나 노튜브의 성장에 미치는 영향을 조사하였다. 증착은 대기압 압력하에서 85$0^{\circ}C$ 의 온도에서 이루어졌다. 순수한 질소 분위기에서는 탄소 나노튜브의 성장이 이루어지지 않고 두꺼운 탄소 층이 기판 위에 중착되었다. 이 조건에서는 탄소로 뒤덮혀진 닉켈 입자가 탄소 나노튜브 형성의 촉매 역할을 담당하지 못했다. 그러나 질소와 수소의 혼합분위기에서는 수소의 농도가 증가함에 따라 탄소 나노튜브의 성장이 증진되었다. 순수한 수소 분위기에서는 일정한 방향이 없이 꼬여진 탄소 나노튜브가 성장되었다. 탄소 나노튜브의 성장은 분위기 가스로 암모니아를 사용하였을 때 훨씬 더 증진되었다. 수직으로 배열된 탄소 나노튜료를 암모니아 분위기에서는 성장시킬 수 있었으나 암모니아와 같은 비율의 수소와 질소 가스의 혼합 분위기 하에서 는 탄소 나노튜브의 성장을 얻을 수 없었다. 이러한 결과를 여기에서는 닉켈 촉매의 표면에 과도하게 석출된 탄소의 촉매 passivation으로 설명하였다. 탄소 나노튜브의 증착을 위해서는 아세틸렌 가스의 분해율이 너무 과도하지 않게 즉 촉매의 표면이 과도한 탄소의 증착으로 수동태화 되지않도록 조절되어야 한다는 것이다. 이 연구결과는 분위기 가스의 조성이 탄소 나노튜브의 성장에 있어서 그 반웅 kinetics에 큰 영향을 미친다는 것을 잘 보여주고 있다. 또한 암모니아 분위기에서는 촉매 닉켈입자 표면에 질화물층이 형성되어 탄소 나노튜브의 성장에 영향을 미쳤다는 것도 알 수 있었다.며 실제 가공업체에서도 터짐 문제가 발견되지 않았다. 결론적으로 표면층의 인장강도가 패션/구부림에 가장 중요한 변수로 작용하며 어떠 한 형태로 표면층의 인장강도를 향상시킬 경우 침엽수 펄프는 재생펄프로 대체가 가능 할 것으로 판단된다.하는 통계기법 중의 하나인 주성분회귀분석을 실시하였다. 주성분 분석은 여러 개의 반응변수에 대하여 얻어진 다변량 자료의 다차원적인 변 수들을 축소, 요약하는 차원의 단순화와 더불어 서로 상관되어있는 반응변수들 상호간 의 복잡한 구조를 분석하는 기법이다. 본 발표에서는 공정 자료를 활용하여 인공신경망 과 주성분분석을 통해 공정 트러블의 발생에 영향 하는 인자들을 보다 현실적으로 추 정하고, 그 대책을 모색함으로써 이를 최소화할 수 있는 방안을 소개하고자 한다.금 빛 용사 둥과 같은 표면처리를 할 경우임의 소재 표면에 도금 및 용 사에 용이한 재료를 오버레이용접시킨 후 표면처리를 함으로써 보다 고품질의 표면층을 얻기위한 시도가 이루어지고 있다. 따라서 국내, 외의 오버레이 용접기술의 적용현황 및 대표적인 적용사례, 오버레이 용접기술 및 용접재료의 개발현황 둥을 중심으로 살펴봄으로서 아직 국내에서는 널리 알려지지 않은 본 기 술의 활용을 넓이고자 한다. within minimum time from beginning of the shutdown.및 12.36%, $101{\sim}200$일의 경우 12.78% 및 12.44%, 201일 이상의 경우 13.17% 및 11.30%로 201일 이상의 유기의 경우에만 대조구와 삭제 구간에 유의적인(p<0.05) 차이를 나타내었다.는 담수(淡水)에서 10%o의 해수(海水)로 이주된지 14일(日) 이후에 신장(腎臟)에서 수축된 것으로 나타났다. 30%o의 해수(海水)에 적응(適應)된 틸라피아의 평균 신사구체(腎絲球體)의 면적은 담수(淡水)에

• Composites Research
• /
• v.30 no.6
• /
• pp.379-383
• /
• 2017

A study on the low Earth orbit (LEO) space environment have been conducted as a use of composites have increased. Among the LEO environmental factors, atomic oxygen is one of the most critical factors because atomic oxygen can react and erode a surface of polymer-based composite materials. POSS (Polyhedral Oligomeric Silsesquioxane) materials have been widely studied as an atomic oxygen-resistant nanomaterial. In this study, nanocomposites, which are composed of OG (Octaglycidyldimethylsilyl) POSS nanomaterials and DGEBA/DDM epoxy, were fabricated to find out its thermal and mechanical properties. FT-IR results showed that the nanocomposites were fully cured and contained OG POSS enough. Thermogravimetric analysis and differential scanning calorimetry were performed to measure the thermal properties of the nanocomposites. The initial mass loss temperature and char yield were increased through the filling of OG POSS. As the content of OG POSS increased, glass transition temperature tended to increase to 5 wt.% of OG POSS, but the temperature decreased significantly at 10 wt.% of OG POSS. The tensile test results showed that the content of OG POSS did not affect tensile strength and tensile stiffness.