• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.6
• /
• pp.4192-4200
• /
• 2015

In this paper, dispersibility of steel fiber is improved mixing with form for material development of protection and blast resistant structure sprayed concrete. And it is developed a high toughness cellular sprayed concrete material using steel fiber. Oversupply form for dispersibility improvement of steel fiber is mostly fade away through sprayed, finally it is satisfied with the proper mixing ratio under 3 % ~ 6 %. This is considered for compressive strength and flexural toughness. Test results of compressive strength showed superior strength capability in 28, 56 days, also flexural strength and flexural toughness is great. Then oversupply form is enhanced for dispersibility of steel fiber and I think that it did not cause decreasing of strength. But analysis results of pore structure through image analysis failed for a great spacing factor and specific surface area. This is largely measured in spacing factor because air content have a grate evaporation effect for sprayed.

• Journal of the Korean Ceramic Society
• /
• v.33 no.3
• /
• pp.339-347
• /
• 1996

Mechanical properties(flexural strength hardness fracture toughness) of alumina ceramics were evaluated. Alumina products of four companies were selected and three of those were made in Korea and one of those was made in Japan. The large differences according to manufacturing companies had resulted from flexural strength and weibull modulus which had a wide ranges of 300 to 400 MPa and 5 to 15 respectively. Critical indenstation load which could be neglected the effect of elastic recovery was about 9.8N and Vickers' hardness were about 15 GPa. Fracture toughnesses were evaluated by IF and ISB method. It was more preferable to the average at one indentation load that fracture toughness were obtained from the slope of the relationship between indentation load and crack length in IF method and between indentation load and fracture load in ISB method and fracture toughness was about 4 MPa·m1/2.

• Journal of the Korea Concrete Institute
• /
• v.27 no.3
• /
• pp.229-236
• /
• 2015

This paper describes the effect of aggregate size on compressive behavior of high-strength steel fiber reinforced concrete. The Specified compression strength is 60 MPa and the range of fiber volume fraction is 0~2%. The main variable is the aggregate size, which was used for the aggregate size of 8 and 20 mm. So, ten concrete mixtures were prepared and tested to evaluate the fresh and hardened properties of SFRC at curing ages (7, 14, 28, 56 and 91 days), respectively. Items estimated in this study are the fresh properties (air contents, slump), hardened properties (compressive strength, modulus of elasticity, post-peak response and compressive toughness). As a result, the aggregate size has little effect on the compressive strength and modulus of elasticity. On the other hand, the ductile behavior was shown after post peak and the compressive toughness was increasing as decreasing the aggregate size. These effects are clearly represented in the fiber volume fraction 2%, which are the point appeared fiber ball. It is considered that the decreasing the aggregate size has effect on the fiber dispersibility.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.10 no.3
• /
• pp.185-196
• /
• 2006

Fracture toughness is a material property for crack initiation and propagation in fracture mechanics. For mode I fracture toughness measurement in concrete, RILEM committees 89-FMT proposed three-point bend tests based on the two-parameter fracture model. But, there is no proposed test method as a standard for mixed mode test for now. And RILEM three-point bend test procedure is complicate. Therefore, in this study, brazilian disks of various size were designed as the concrete with a similar specified concrete strength and maximum size of coarse aggregate($G_{max}$) were respectively 20mm and 40mm. And mode I fracture toughness of brazilian disks was compared with that of RILEM three-point bend test. As a result, it was suggested appropriate size(thickness, diameter) and notch length ratio of brazilan disk on the $G_{max}$. And it was verified that stress intensity factors for mixed mode can be easily calculated with the disk specimen. Stress intensity factors of a concrete brazilian disk were evaluated with finite element analysis and five terms approximation for comparison.

• Korean Journal of Childcare and Education
• /
• v.5 no.2
• /
• pp.1-20
• /
• 2009

This paper is intended as an investigation of relation between pre-service kindergarten teacher's creative personality and teacher's efficacy. Subjects of this study were 160 third grade students of S collage & Y collage. They were major in infant or early childhood education and have an field practice experience of nurture and education. Tool for measurement is Creative Personality Scale of Ha Juhyun and TEBI(Teaching Efficacy Belief Instrument) teacher's efficacy test which is modified by Kim Sunnam. The collected data were analyzed by one-way ANOVA, post hoc Scheffe' test, Pearson's correlation and stepwise regression. The following results were obtained. First, there is no difference in creative personality according to academic grade, age, experience of leadership in collage. Second, there is a static relation between age of pre-service kindergarten teacher and teacher's efficacy especially personal teacher's efficacy. Third, points of creative personality is relative to teacher's efficacy, especially relative to personal teacher's efficacy. Among the sub-factors of creative personality, factors estimates teacher's personal efficacy are 'self belief, imagination and open mind'. On these ground, I comment on curriculum which will educate creative personality of pre-service kindergarten teacher.

• Journal of Christian Education in Korea
• /
• v.66
• /
• pp.383-412
• /
• 2021

The purpose of this study is to analyze the journal of reflection of students who participated in the character improvement education program. And it is a study that suggests ways to develop the program according to the results of analysis. Then, by collecting 208 reflective journals of students who participated in Milal training at K University, After the analysis was performed in the process of transcription, coding, and subject discovery, reliability was secured by calculating the Kappa coefficient for the analysis frame and analysis suitability. According to the results of the analysis of reflection journal. Through Milal training, the Milal spirit was understood as sacrificial service (sacrifice, devotion, lowering, serving, death, decay) and Milal (reproduction). We confirmed that It will have a life attitude related to the themes of labor (hardwork, work, patience, patience, perseverance). It can be said that through Milal training, self-reflection activities can be promoted, community character and collaboration skills can be cultivated, and the spirit of sacrificial service can be acquired. Through the results of this reflection journal analysis, it is necessary to further enhance the Milal training program, and it will be possible to provide implications to the character cultivation programs of other universities.

• Composites Research
• /
• v.14 no.3
• /
• pp.51-56
• /
• 2001

It is known that the elastic modulus, maximum stress, and maximum strain of fiber-reinforced polymer composites are affected by high pressure. Fracture behavior is also known to be affected by high pressure. In this work, the pressure effect on the compressive fracture toughness of thick quasi-isotropic composites was investigated. Dog-bone type specimens of stacking sequence, [0$^{\circ}$/$\pm$45$^{\circ}$/90$^{\circ}$]$_{11s}$ were used. Compressive fracture tests were conducted under four pressure levels. The pressure levels applied were 0.1 MPa, 100 MPa, 200 MPa, and 300 MPa. Fracture toughness for each pressure level was determined from the compliance method. The results show that the compressive fracture toughness increases with increasing pressure. Specifically, fracture toughness increases 44% as the pressure increases from 0.1 MPa to 300 MPa.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.5
• /
• pp.1472-1478
• /
• 1991

본 연구에서는 Rectangular Computer Tension(CT) 시편을 수정하여 만든 표준 시편인 MRL-CLWL시편(material research laboratorycrack line wedge loaded specimen )으로 균열정지 인성치를 결정하였다. 그리고 CT시편과 같은 효과를 갖는 Newman등 이 제안한 round compact tension(RCT)시편을 수정한 Round-CLWL 시편으로 균열정지인 성치를 결정하여 상호 비교평가하였다. Round-CLWL 시편은 시편제작시 round-bar를 절단하여 시편으로 가공할 수 있으므로 가공성이 좋으며 따라서 가공비가 적게 든다. 특히 균열 위치 및 방향을 임의로 선택하여 가공하기가 용이하므로 방향성이 있는 소 재의 균열정지 인성치를 결정하는 데 매우 편리한 시편이라 생각된다. 본 논문에서 는 Round-CLWL 시편으로 $K_{1a}$ 값을 계산하는데 필요한 형상계수를 결정하였으며, Polymethylmethacrylate(PMMA)를 사용하여 Round-CLWL 시편 채택의 타당성 확인을 위 한 MRL-CLWL과 Round-CLWL 시편 채택의 타당성 확인을 위한 MRL-CLWL과 Round-CLWL시 편의 $K_{1a}$결정 실험을 하였다.하였다.

• Tunnel and Underground Space
• /
• v.19 no.2
• /
• pp.95-106
• /
• 2009

Numerical analysis of the progressive failure of a rock slope was conducted using a 3-D rock joint element considering fracture mechanics and subcritical crack growth of asperities in the rock joints. Even though the stress state in the rock slope is not changing, the elapse of time causes subcritical crack growth to break asperities in the joints. The increase of broken asperities causes failure of joints in the rock slope and the increase of failed joints results in failure of a jointed rock slope. As a result, the progressive failure of a jointed rock slope due to the gradual breaking of small asperities along joints generated by subcritical crack growth occurs at a lower stress than if rock failure occurred by exceeding the static strength or fracture toughness.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.346-351
• /
• 2003

In this paper, an evaluation method of fracture toughness on interface cracks has been investigated under various mixed-mode conditions of the bonded scarf joints. Two types of the bonded scarf joints with an interface crack were prepared to analyze the stress intensity factors using boundary element method(BEM) and to perform the fracture toughness test. From the results of fracture toughness experiments and BEM analysis, an evaluation method of fracture toughness on interface cracks in the bonded components of dissimilar materials has been proposed and discussed.