• Magazine of RCR
• /
• v.14 no.2
• /
• pp.28-34
• /
• 2019

• Fire Science and Engineering
• /
• v.23 no.6
• /
• pp.116-125
• /
• 2009

This study is progressed function ratio, it's trued taste by an experiment to present data for human work light weight aggregate development that use clink ash progressed liquid limit, small success limit, wear loss in quantity, sand equivalent, sieve cutting examination. 80 : 20's match of function rain examination is 1.4, and that use rubble Goljae as ckink ash lightweight aggregate's capacity ratio increases by 1.0 increase of function rain many. Also, examination multiplied delicate flavor gradually according to increase of the mixing rate, and absorption coefficient increased. This is judged by phenomenon that appear by special quality upper clink ash of polystyrene bid and porosity's increase between lightweight aggregate. It is case that use aggregate of wear loss in quantity is 13.5 in sand equivalent and a wear loss in quantity experiment and although case that mix 20% increases by 14.4, this phenomenon by weak tissue of lightweight aggergate be judge. When it's as a these experiment, the statue prevention floor of a street improvement specifications is prescribing so that satisfy by sand equivalent 20, CBR 10. This is showed result that this satisfies in quality standard all in match experiment ago that see.

• Journal of the Korea Institute of Building Construction
• /
• v.18 no.2
• /
• pp.133-140
• /
• 2018

The objective of this study is to propose a reliable mixing design procedure of concrete using artificial lightweight aggregate produced from expanded bottom ash and dredged soil. Based on test results obtained from 25 mixes, empirical equations to determine water-to-cement ratio, unit cement content, and replacement level of lightweight fine aggregates were formulated with regard to the targeted performance (compressive strength, dry density, initial slump, and air content) of lightweight aggregate concrete. From the proposed equations and absolute volume mixing concept, unit weight of each ingredient was calculated. The proposed mix design procedure limits the fine aggregate-to-total aggregate ratio by considering the replacement level of lightweight fine aggregates, different to previous approach for expanded fly ash and clay-based lightweight aggregate concrete. Thus, it is expected that the proposed procedure is effectively applied for determining the first trial mixing proportions for the designed requirements of concrete.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2010.05a
• /
• pp.247-248
• /
• 2010

This study is of manufacturing artificial lightweight aggregates using industrial wastes. The ingredients for manufacturing lightweight aggregate were stone sludge and bottom ash for main materials, and steel slag(SS), glass abrasive sludge(GS) and blast furnace slag(BS) respectively for accessory material. Their precursors were sintered in the range of $1,050{\sim}1,150^{\circ}C$ for 5 min. The sintered results show that the lightweight aggregate with SS had low water absorption ratio and density at $1,150^{\circ}C$. There's a possibility that if GS is used more than the range of this study, GS can be manufactured lightweight aggregate. But it is judged that BS are incongruent to be used for a raw material of lightweight aggregate.

• Industry Promotion Research
• /
• v.6 no.4
• /
• pp.1-9
• /
• 2021

The purpose of this study is to manufacture lightweight aggregates for recycling water treatment sludge, to identify the physical properties of the aggregates, and present a method of utilizing the manufactured lightweight aggregates. The chemical composition and thermal properties were examined via a raw materials analysis. The aggregate examined here was fired by the rapid sintering method and the single-particle density and water absorption rate were measured. Water treatment sludge has high ignition loss and high fire resistance. When 30wt% of purified sludge was added, the single-particle density of the aggregates was in the range of 0.8~1.2g/cm³ at a temperature of 1,150~1,200℃. At temperatures of 1200℃ or higher, ultra-light aggregates having a single-particle density of 0.8 or less could be produced. When applied to concrete by replacing the general aggregate in the concrete, a specimen having strength values of 200 to 450 kgf/cm² on 28 days was obtained, and when applied as a filter material, the performance was equal to or higher than that of ordinary sand.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.19 no.6
• /
• pp.318-323
• /
• 2009

The lightweight aggregates made of bottom ash (70 wt%) and dredged soil (30 wt%) were prepared to investigate the property differences at various sintering atmospheres. The green aggregates were sintered at $1150^{\circ}C$ and $1200^{\circ}C$ with oxidized, neutralized and reduced atmospheres. The aggregates sintered with oxidized atmosphere showed a clear border between shell and black core area. However, the aggregates sintered with a reduced atmosphere showed only black core area in the entire cross-section of the aggregates. The black core area of the aggregates sintered with a neutralized atmosphere increased with increasing $N_2$ gas flow rates. It was determined that the sintering atmosphere was similar to that of rotary kiln when the CO gas flow was 100 cc/min to make a reduced atmosphere in tube furnace. The water absorption rates of both aggregates from tube furnace with reduced atmosphere and rotary kiln were very similar to each other.

• Journal of the Korea Concrete Institute
• /
• v.21 no.2
• /
• pp.147-152
• /
• 2009

The compressive strength test, bulk density and mortar absorption ratio were carried out to utilize the data as the basic sources for the lightweight mortar and the lightweight concrete, through the study on the physical characteristics of the artificial lightweight aggregate (ALA) made of waste glasses, which was developed for the first time in the country. On the basis of these experiments, the density and the unit volume weight of the ALA showed the value less than 50% of the common aggregate due to the independent pore structure, and the mortar that contains ALA had no big difference from the Control mortar in the test of the absorption ratio. It is judged that this happens based on the internal independent pore structure of the ALA. In case of the mortar containing ALA, there was a tendency of declination in the compressive strength and the bending strength as the mixing rate is increasing, but all mortar showed more than 70% of the Control mortar compressive strength except for the La50 mortar. Hereafter, it is judged that according to the control of the mixing ratio of mineral admixing agent, water and cement, it will realize the equal strength to the control mortar, and the long term edurance is needed to be considered together.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2018.05a
• /
• pp.218-219
• /
• 2018

This study analyzed the unit weight and compressive strength properties of lightweight concrete using high volume blast furnace slag powder by the mixing ratio of lightweight coarse aggregate to investigate the properties of lightweight concrete using domestic artificial lightweight aggregate.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2018.11a
• /
• pp.118-119
• /
• 2018

The purpose of this study is to investigate the compressive strength and mixing properties of the lightweight block, which has been manufactured without the pre-wetting process, in the lightweight block using domestic artificial lightweight aggregate. The test results of the specimens produced within 30 minutes after the preparation showed high compressive strength but poor permeability. Therefore, the elapsed time after the manufacture, which is expected to have required compressive strength and permeability, was about 60 minutes in this study.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2019.11a
• /
• pp.153-154
• /
• 2019

In this study, the fluidity and compressive strength of lightweight mortar using recycling water for pre-wetting of artificial lightweight aggregate were compared and analyzed to maximize the utilization of the recycling water, which is a by-product of the Ready-Mixed Concrete industry. For this purpose, the pre-wetting water was replaced with recycling water at the ratio of 0, 2.5, 5, 7.5 and 10%.