• Proceeding of EDISON Challenge
• /
• 2013.04a
• /
• pp.331-336
• /
• 2013

본 연구에서는 인간동력 항공기의 주익에 적용할 에어포일 형상에 대한 공력 특성을 파악하였다. 인간동력 항공기 날개에 적용하기에 적절한 에어포일을 조사하였으며, DAE11, DAE21, DAE31, SG6043 익형에 대하여 전산유체해석 프로그램인 EDISON_CFD를 통하여 비교하였다. 인간동력 항공기의 낮은 비행속도를 감안하여 $6{\times}10^5$의 저 레이놀즈수에서 받음각에 따른 양력계수, 항력계수, 양항비 등을 얻어내어 상호 비교 분석하였다. 본 연구를 통해 인간동력 항공기 주익에 적용할 저 레이놀즈 에어포일 형상을 최종적으로 선택할 수 있는 근거 자료를 확보하였다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.5
• /
• pp.1-11
• /
• 2006

The effects of continuous blowing on flow control and stall suppression for flows over a NACA 0015 airfoil at low Reynolds numbers were numerically investigated through its parameter variation on unstructured meshes. The aerodynamic force and moment variations due to flow control were examined, along with the stall angle-of-attack change for stall suppression. The results showed that blowing with relatively strong jet increases lift at the cost of drag increment below stall angle. Continuous blowing delays flow stall when it is implemented near the leading edge. When the blowing jet was aligned along the flow direction on the airfoil, the favorable flow control effect was most significant below the stall angle of attack.

• Proceeding of EDISON Challenge
• /
• 2016.03a
• /
• pp.632-637
• /
• 2016

This study shows what difference would be made to the aerodynamic characteristic with different thickness ratio of the same airfoil, Eppler 387, at low Reynolds number, at the angle of attack of $0^{\circ}$. Konkuk Univ.'s airfoil has a bigger thickness ratio than that of the original Eppler 387 airfoil. The reason for the thicker camber is a Pt 100 ohm heater mounted inside the Konkuk Univ.'s airfoil and this was assumed to make some differences to aerodynamic characteristic. The comparison of these two airfoils' CFD data, provided by EDSION_CFD, with real experiment that had been made in subsonic wind tunnel at Konkuk Univ. is done. A finer result would come out if the complement of the homogeneity of the wind tunnel's fluid is done in the future.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.06a
• /
• pp.47-50
• /
• 2005

본 연구의 목적은 차세대 대체에너지로 각광받는 풍력발전 중에서 육상발전보다 여러 가지 이점이 있는 해상에서의 한국형 풍력터빈 블레이드의 최적 형상을 위 한 알고리즘을 구현하는 것이다. 풍력터빈 블레이드에서 깃익형의 공기 역학적 특성은 매우 중요한 사항이다. 이를 위해서 익형 성능예측에 층류에서 난류로의 천이과정을 포함하는 XFOIL을 이용하여 블레이드 익형 단면의 양력과 항력 분포를 해석하였다. 첫 번째 수준의 설계변수는 운용범위내의 바람의 속도와 블레이드 지름, 축 회전수이며, 각 단면에서의 비틀림각과 시위길이는 두 번째 수준의 설계 변수이다. 운용범위 내의 각 설계점에서 익형의 공력 변수들과 최소에 너지손실 조건을 이용하여 시위길이와 피치각 분포를 최적화하였다. 각각의 설계점에서 결과를 바탕으로 풍력발전의 설계 운용범위에서 반응면을 구성하고 구배최적화 기법을 통해 요구동력의 제약함수를 만족하고 효율을 최대로 하는 블레이드 형상을 구현하였다. 최적형상에 대해 탈설계점 해석을 수행하여 그 성능을 구하였다.

• Journal of the Korean Society of Visualization
• /
• v.21 no.2
• /
• pp.83-90
• /
• 2023

The shape of an airfoil is a critical factor in determining aerodynamic characteristics such as lift and drag. Aerodynamic properties of an airfoil have a decisive impact on the performance of various engineering applications, including airplane wings and wind turbine blades. Therefore, it is essential to analyze the aerodynamic characteristics of airfoils. Various analytical tools such as experiments, computational fluid dynamics, and Xfoil are used to perform these analyses, but each tool has its limitation. In this study, airfoil parameterization, image recognition, and artificial intelligence are combined to overcome these limitations. Image and coordinate data are collected from the UIUC airfoil database. Airfoil parameterization is performed by recognizing images from image data to build a database for deep learning. Trained model can predict the aerodynamic characteristics not only of airfoil images but also of sketches. The mean absolute error of untrained data is 0.0091.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.9
• /
• pp.890-899
• /
• 2010

An experimental study has been conducted to analyze the operating forces on a partially admitted turbine blade using a linear cascade apparatus. Axial-type blades were used and the blade chord was 200mm. The rectangular nozzle was applied and its size was $200mm{\times}200mm$. The experiment was done at $3{\times}10^5$ of Reynolds number based on the chord. The rotational force and axial force on the blade were measured at steady state by moving the blade to the rotational direction. The operating forces were measured at three different nozzle install angles of $58^{\circ}$, $65^{\circ}$ and $72^{\circ}$ for off-design performance test. In addition, three different solidities of 1.25, 1.38 and 1.67 were applied. From the results, the maximum rotational force was increased when the solidity was decreased and the nozzle install angle was decreased. The axial force was increased by decreasing the nozzle install angle. The reverse axial force was obtained in the partially admitted region when the nozzle install angle was increased to $72^{\circ}$.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.3
• /
• pp.6-13
• /
• 2006

Aerodynamic characteristics for two-dimensional cyclic motion profile of flapping airfoil in low Reynolds number flows are investigated. Plunging motion and lead-lag motion in the two dimensional space with different plunging and lead-lag amplitudes are combined to cyclic motion profile and the flow around the airfoil is simulated. Present result shows that the improved aerodynamic efficiencies for a given flapping airfoil by adding periodic lead-lag motion of airfoil rather than the pure plunging case. The thrust coefficient and lift coefficient are compared with each cycle during the flapping period and aerodynamic characteristics are obtained on upstroke motion and downstroke motion.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.45 no.3
• /
• pp.259-267
• /
• 2017

Flow fields around a KARI-11-180 airfoil, SDM and transonic body are numerically simulated by using an unstructured meshes based compressible flow solver developed at KAIST. RANS equations are solved to analyse the flow fields and Roe's FDS method is adopted to evaluate convective fluxes. Turbulence effect of the flow fields is modeled by a SA model, SST model and ${\gamma}-{\widetilde{Re}}_{{\theta}t}$ model. It is found that smaller drag coefficients are predicted for the KARI-11-180 airfoil when a transition phenomenon is considered and small deviations exist between CFD and EFD results. For the SDM, flow separation is observed at a leading edge and calculated aerodynamic properties show similar tendencies to experimental results. A shock wave on main wings of the transonic body is successfully captured by the present flow solver at a Mach number 0.9. Estimated pressure profiles by means of the present CFD method also agree well with those of wind tunnel results.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.4
• /
• pp.28-34
• /
• 2019

In this study, pin-fin arrays, which are widely used for cooling turbine blades, were studied. The vortex generator in pin-fin arrays is located in front of the circular tube. The cross-section of the vortex generator is NACA-9410. The purpose of this study is to analyze heat transfer performance and flow characteristics of pin-fin arrays. The position of vortex generator is changed with the vertical flow direction on the bottom wall. Pin-fin arrays were calculated with 6000, 10000 and 15000 Reynolds number. The commercial program ANSYS v18.0 CFX and the turbulence model $k-{\omega}$ SST were used. As a result, the heat transfer performance increased up to 5.8% and pressure loss increased less than 1%.

• Journal of computational fluids engineering
• /
• v.19 no.4
• /
• pp.75-79
• /
• 2014

In the paper, a study on the analysis of the effects of trailing edge thickness on the aerodynamic characteristics of an airfoil is described. In this research, modification of the formula representing NACA symmetric airfoil is studied to change the airfoil shape with different trailing edge thickness of user's choice. According to the result of aerodynamic characteristics, as the trailing edge thickness increases the maximum lift coefficient increases while the lift-to-drag ratio decreases. In this paper flow calculation results are demonstrated and the analysis on those results and findings on the effects of non-zero thickness of trailing edge are suggested.