• 한국해양공학회지
• /
• 제19권2호
• /
• pp.53-59
• /
• 2005

The effect of pH on the corrosion characteristics in the dissimilar friction welded zone of IN713LC-SCM440 in the loaded torsional stress was studied. The corrosion experiment was performed for 120 hours on the specimens with five steps of pH. The surface corrosion pattern of the SCM440 area showed global corrosion and narrow pitting, which was caused by galvanic corrosion between friction welded IN713LC and SCM440, but corrosion did not proceeded from the IN713LC area. The average relative electrode potential gradually tends to decrease with the elapse of the immersion time in the acidity area. The average corrosion current also gradually tend to decrease The corrosion rate showed a larger value when the average relative electrode potential was higher and the average relative current was lower. The corrosion rate showed a larger value when the average relative electrode potential was higher in the acidity area, and it showed large when the average relative electrode potential was lower in the alkalinity area.

• 대한기계학회논문집
• /
• 제19권4호
• /
• pp.929-940
• /
• 1995

The fatigue strength and fracture topography in the friction welded interface of high speed steel (HSS-Co) to SM55C carbon steel have been investigated through the fatigue test, SEM fractograph and EDS (energy dispersive spectrometer) analysis. Three kinds of specimens used in this research are the friction welded joints, HSS-Co and SM55C carbon steel with circumferential notch, saw notch and smooth, respectively. The notch sensitivity factor, .eta. of the friction welded joints is lower than that of the base materials, and that represents a superiority of the joint performance of FRW. Fracture topography of the FRW specimens with a notch showed a cleavage or brittle appearance, while that of the FRW smooth specimen appeared to be ductile. Furthermore, although fatigue crack likely initiated near the weld interface of the FRW smooth specimen, crack propagation continued into the HAZ of SM55C steel. Finally, fatigue fractures of the base materials were associated primarily with the inclusions located at the outer periphery of the specimen.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2009년 추계학술발표대회
• /
• pp.49-49
• /
• 2009

마찰교반접합법은 특정한 회전수로 회전하는 용접 툴을 이용하여 접합하고자 하는 피접합재의 맞댄면에 삽입시킨 후 툴을 이동시키거나 혹은 시편을 견고하게 고정시킨 장치(backing plate)가 움직여 고상 상태에서 접합이 이루어진다. 알루미늄, 마그네슘 등 비교적 융점이 낮은 저융점 재료의 재료에 처음 적용이 되어 많은 연구가 활발히 진행되었고 타 용접방법에 비해 우수한 접합특성을 나타내었다. 최근 이러한 마찰교반접합은 이러한 저융점 재료를 넘어서 스틸, 타이타늄, 니켈 등과 같은 고융점 재료 등에 대한 적용이 늘어나고 있다. 마찰교반접합을 이용하여 이러한 고융점 재료의 접합 경우 내마모성 및 내열성 등의 내구성이 갖추어진 툴과 이러한 툴을 냉각시킬 수 있는 냉각 장치 등이 필요로 하나 경제적 측면이나 접합부의 우수한 특성 등을 고려 할 때 그 적용 및 발전 가능성이 매우 높다고 볼 수 있다. 최근 무공해 연료로 각광받고 있는 액화천연가스 (LNG)의 수요가 급증함에 따라 LNG 저장탱크 소재로 널리 사용되고 있는 9% Ni강의 수요 또한 증가하고 있는 상황이다. 하지만 9% Ni 강은 극저온용 소재로 용접부의 저온인성 ($-196^{\circ}C$)이 가장 중요하기 때문에 저온인성을 확보하고자 Inconel 계나 Hastelloy계 등의 니켈 기 합금을 용접재료로 사용하고 있으나 이러한 용접재료는 가격이 매우 고가이며 또한 용접 후 용접부의 강도가 낮다는 문제가 제기되고 있다. 또한 LNG 탱크 제작시 사용되는 용접법은 GTAW, SAW 및 SMAW 이지만 국내에서는 주로 SMAW에 의존하고 있는 실정인 관계로 보다 더 경제적인 용접 프로세스의 적용 가능성이 검토되고 있는 상황이다. 본 연구에서는 마찰교반용접을 이용하여 두께 4mm의 9% Ni 강에 대해 맞대기 마찰교반접합을 실시하였다. 툴 회전 속도 및 접합 속도를 고정한 상태에서 접합을 실시 하였으며 접합 시 툴은 $Si_3N_4$로 제작된 툴을 사용하였다. 접합 후 외관상태 점검, 미세조직 관찰, 경도, 인장 강도 및 저은 충격 측정 등의 실험을 실시하였고, 이러한 결과를 이용하여 미세조직과 기계적 특성과의 관련성을 조사하였다.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2000년도 추계학술대회 논문집
• /
• pp.42-46
• /
• 2000

In this paper, joints of Cu-1Cr-0.1Zr alloy to STS316L were performed by friction welding method. Cu-1Cr-0.1Zr alloy is attractive candidate as nuclear power plant material and exibit the best combination of high sts good electrical and thermal conductivity of any copper alloy examined. The stainless steel is a structural material who alloy acts as a heat sink material for the surface heat flux in the first wall. So, in this paper, not only the develop optimizing of friction welding with more reliability and more applicabililty but also the development of in-process rear quility(such as strength and toughness) evaluation technique by acoustic emission for friction welding of such nuclear component of Cu-1Cr-0.1Zr alloy to STS316L steel were performed.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2000년도 추계학술대회 논문집
• /
• pp.26-32
• /
• 2000

It was confirmed that the life predictive equation by LMP-ISM are effective only up to 10$^2$hours and can not be used for long times of 10$^3$~10$^{5}$ hours, but that by ISM can be used for long times creep life prediction with more reliability. The predictive creep life equation of ISM has better reliability than those by LMP and LMP-ISM, and its realizably is getting better for long time creep prediction(10$^3$~10$^{5}$ H).

• 한국안전학회지
• /
• 제16권3호
• /
• pp.19-25
• /
• 2001

The friction-welding SM25C is a substitute for the suing steel that is utilized in the machinery, airplane, and automobile, ok. This substitution would provide reduction of material and weight of welding parts. From the result we found that the strength of the friction welded joint was 529-617MPa and the toughness 1.2 times higher than that of the base metal. The optimal condition of friction welding was found as follows : n=2000rpm, $P_1$=68㎫, $P_2$=137MPa, $t_2$=2sec, $t_1$=2-4sec, Considering the strength, the hardness, and the reduction of area in the friction welding, the fiction welding using SUP9A and SM25C was found to cause no problem in on-the-job application.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1996년도 추계학술대회 논문
• /
• pp.161-166
• /
• 1996

In this study behavior of deformation and fracture under static tensile load in friction welded dissimilar materials and necking 0phenomenon occuring at tensile yeilding point were shown. Fibrous zone with view of macroscope and dimple pattren with a view of microscope were observed at shear surface.

• 동력기계공학회지
• /
• 제10권1호
• /
• pp.77-82
• /
• 2006

In this study, dissimilar friction welding were produced using 15mm diameter solid bar in chrome molybedenum steel(SCM440) to carbon steel(S45C) to investigate their mechanical properties and the relationship between the weld parameters and the nondestructive coefficients, such as AE counts and ultrasonic attenuation coefficient. The main friction welding parameters were selected to endure good quality welds on the basis of visual examination, tensile tests, Vickers hardness surveys of the bond of area and heat affected zone. The specimens were tested as-welded and post weld heat treated(PWHT). The tensile strength of the friction welded steel bars was increased up to 100％ of the S45C base metal under the condition of all heating time. The ductility of PWHT specimens is higher than as-welded.

• 한국산업융합학회 논문집
• /
• 제22권2호
• /
• pp.191-199
• /
• 2019

In this paper, dissimilar friction welding were produced using 15 mm diameter solid bar in chrome molybedenum steel(SCM440) to stainless steel(STS316L) to investigate their mechanical properties. Consequently, optimal welding conditions were n=2000 rpm, HP=70 MPa, UP=140 MPa, HT=10 sec and UT=10 sec when the metal loss(Mo) is 8.6 mm. In addition, an acoustic emission technique was applied to evaluate the optimal friction welding condition. AE parameters including the cumulative count, amplitude and energy showed a various changes according to the friction condition. A continuous type waveforms and low frequency spectrum was presented in friction time. On the other hand, a burst type waveform and high frequency spectrum was exhibited in pressing time.

• Journal of Welding and Joining
• /
• 제34권3호
• /
• pp.17-22
• /
• 2016

In terms of mechanical and metallurgical characteristics, the effect of tool plunge depths(0.2, 0.5, 0.7, 1.0, 1.5mm) on weldability in dissimilar Al5083-O/DP590 friction spot joint has been clarified. From the results, it is found that the stirred nugget was stably formed at a plunge depth of more than 0.7mm, which is caused by improved stirring action against each other material. With increasing a plunge depth, the thickness of intermetallic compound(IMC) layer in Al5083-O/DP590 joint has a tendency to increase. The tensile shear strength reaches to the maximum failure load of 6.5kN at a plunge depth of 0.7mm due to relatively small decrease in the thickness of Al5083-O sheet and relatively minute thickness of IMC layer, compared with those of other plunge depth conditions.