• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.11a
• /
• pp.343-344
• /
• 2008

• Journal of Welding and Joining
• /
• v.14 no.3
• /
• pp.75-85
• /
• 1996

In this paper the influence of postweld heat treatment on mechanical properties of SMAW and FCAW stainless steel weldments was examined and the obtained results are as follows ; (1) The amount of $\delta$-ferrite formed by SMAW and FCAW process decreased with increasing holding temperature and time in post weld heat treatment(PWHT), and it was found that the reduced ferrite was transformed into sigma phase after $800^{circ}C{\times}50hr$ PWHT. This sigma phase, even though it was very small, resulted in brittleness of dissimilar weldment between carbon steel and stainless steel in bending test, however in similar weldment between stainless steel and stainless steel was not occured. (2) The chemical composition of sigma phase was measured to 28-30%Cr, 7-9%Mo, 4-6Ni in 316L weldment, and also 35-37%Cr, 0.9-1.0Mo, 6-8%Ni in 309L weldment by EDS analysis.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.3
• /
• pp.333-340
• /
• 2010

This paper presents the distributions of the tensile and fracture properties of an alloy 82/182 dissimilar weld joint between an SA508 Gr.3 nozzle and F316L SS safe-end at ambient temperature. Tensile and J-R tests were conducted using specimens extracted from base metals, heat-affected zones (HAZs), buttering regions, and various regions of the weld metal. The results show that the root region of the weld has higher strength than the upper region. The yield and tensile strengths vary considerably within the root region of the weld. The buttering region had the lowest strengths. The strengths gradually increased as the F316L stainless steel weld boundary was approached. The variation of the strengths within the upper region of the weld is insignificant. The fracture toughness of the alloy 82/182 weld metal is less than those of both the base metals and both HAZs. Within the alloy 82/182 weld, the center of weld has a slightly lower fracture toughness than the weld boundary and buttering region, and the root region has greater toughness than the upper region of the weld.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.244-249
• /
• 2007

In several locations of the pressurized water reactors, dissimilar metal welds using inconel welding wires are used to join the low alloy steel nozzles to stainless steel pipes. To evaluate the integrity and design the dissimilar welds, tensile and fracture properties variations are needed. In this study, dissimilar metal welds composed of SA508 Gr.3 LAS, inconel 82/182 weld, and TP316 stainless steel were prepared by gas tungsten arc welding and shielded metal arc welding technique. Microstructures were observed using optical and electron microscopes. Different tensile and fracture properties were observed depending on the specimen sampling position at room temperature and $320^{\circ}C,$ and that was discussed based on the microstructure characteristics. It was found that the strength at the bottom of weld was greater than at the top of the weld. Also, from the test data using small punch specimen, more detailed tensile property variations were evaluated.

• The Journal of Korean Academy of Prosthodontics
• /
• v.50 no.1
• /
• pp.53-60
• /
• 2012

Purpose: The purpose of this study was to compare Ni-Cr alloy property of gas-oxygen torch soldering and infrared welding using optical microscope and Electron Probe Micro Analyzer (EPMA). Materials and methods: Ni-Cr alloys were casted for specimens. Specimens had 3.0 mm diameter, 30.0 mm length and were divided into two groups. Each group had 4 specimens. One group was for gas-oxygen torch soldering and the other was infrared welding. Specimens were cut with low-speed disc and soldered each other with gas-oxygen torch and infrared machine. After soldering and polishing, specimens were observed at 3 points (soldering point, 5 mm distance point, 10 mm distance point) with optical microscope and analyzed 3 points (soldering point, 5 mm distance point, 10 mm distance point with EPMA. Results: The results of this study were as follows: 1. The observation of gas-oxygen torch soldering at 10 mm distance point under the optical microscope was not founded any specific surface properties, but some crack lines were observed at 5 mm distance and soldering point. 2. There were no crack lines were founded at the observation of infrared welding at 10 mm distance and 5 mm distance points under the optical microscope. However, at the 5 mm distance, the surface was not smooth enough compared with at 10 mm distance point. Some crack lines were observed at the welding point as well. 3. In the EPMA analysis of the gas-oxygen torch soldering, the component of Ni was increased by 4.5%, Cr was increased by 7.5% than that of the Ni-Cr alloy at the 10.0 mm distance. At the 5 mm distance, the component of Ni was decreased by 6.1%, Mo was increased by 9.0% than that of the Ni-Cr alloy but Cr was equally shown at the 5.0 mm distance. Only Ni was shown at the soldering point. 4. In the EPMA analysis of the infrared welding, the component of Ni was increased by 9.1%, Cr was increased by 0.4% than that of the Ni-Cr alloy but Al was equal at the 10.0 mm distance. At the 5 mm distance, the component of Ni was increased by 4.7%, Cr was increased by 4.7% and Al was increased by 0.1% than that of the Ni-Cr alloy. At the welding point, the component of Ni was increased by 8.8%, Cr was increased by 8.2% than that of the Ni-Cr alloy. Conclusion: From these results, at the 5 mm distance from the soldering point, the surface of the infrared welding was more smoother than that of the gas-oxygen torch soldering. On the EPMA analysis, the component of the specimens with infrared welding was more similar than that of the gas-oxygen torch soldering compared with the component of the Ni-Cr alloy.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.98-103
• /
• 2008

This paper is to discuss distribution of welding residual stresses of a ferritic low alloy steel nozzle with dissimilar metal weld using Alloy 82/182. Two dimensional (2D) thermo-mechanical finite element analyses are carried out to simulate multi-pass welding process on the basis of the detailed and fabrication data. On performing the welding analysis generally, the characteristics on the heat input and heat transfer of weld are affected on the weld residual stress analyses. Thermal analyses in the welding heat cycle process is very important process in weld residual stress analyses. Therefore, heat is rapidly input to the weld pass material, using internal volumetric heat generation, at a rate which raises the peak weld metal temperature to $2200^{\circ}C$ and the base metal adjacent to the weld to about $1400^{\circ}C$. These are approximately the temperature that the weld metal and surrounding base materials reach during welding. Also, According to the various ways of appling the weld heat source, the predicted residual stress results are compared with measured axial, hoop and radial through-wall profiles in the heat affected zone of test component. Also, those results are compared with those of full 3-dimensional simulation.

• Journal of Welding and Joining
• /
• v.10 no.1
• /
• pp.12-19
• /
• 1992

용접능률의 향상을 위한 대입열용접법의 적용은 과도한 입열량으로 인하여 용접부의 인성이 저 하한다는 점에서 그 적용에 주의를 요한다. 본 보에서는 대입열용접시 열영향부의 인성 저하의 원인과 그 대책을 강재의 측면에서 검토하였다. 고장력강을 용접하면 입열량이 증가함에 따라 오스테나이트 결정립이 조대화되고 상부 베이나이트와 도상 마르텐사이트가 생성되어 인성이 저하한다. 그 대책으로서는 용접 열싸이클과정중 안정한 질화물, 산화물등을 모재에 미세분산시켜 오스테나이트 결정립 성장을 억제하고, 페라이트, 펄라이트 변태를 촉진시킨다. 이러한 석출물의 형성을 위해서는 주로 Ti, Ca, REM, B등의 합금원소가 이용된다. 소입성이 높은 주질고장력 강에서는 석출물의 분산에 의한 페라이트의 변태 촉진 보다는 Mn, Ni, Cr, Mo, V등의 합금원 소를 첨가하여 소입성을 높여 인성이 우수한 하부 베이나이트 조직을 형성하든가, 탄소량을 저 감시켜 도상 마르텐사이트의 생성을 억제하므로서 인성을 확보한다. 현재 국내에서 제조되고 있는 대입열용접용강중 인장강도 50kgf/mm$^{2}$급강은 기본적으로 용접부 인성이 우수한 TMCP법으로 제조되며, Ti등을 첨가하여 석출물의 효과를 이용하고 N을 억제하여 기지의 인 성을 향상시키는 등의 방법을 병용하고 있다. 인장강도 60kgf/mm$^{2}$ 급강은 조질처리에 의하여 제조되며, 50kgf/mm$^{2}$급강과 같이 Ti, B등의 첨가에 의한 석출물의 효과를 이용 하고 있다.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2006.06a
• /
• pp.29-30
• /
• 2006

나이모닉 일체형으로 사용되고 있는 선박용 2 행정 저속엔진의 배기밸브 스핀들을 고온, 고압, 배기가스 및 반복 충격 하중에 노출된 스핀들의 Head부분은 기존의 나이모닉 소재를 적용, 기존 재질의 우수한 성질을 유지하고 설계적으로 나이모닉 소재의 적용이 불필요한 Stem부는 오스텐나이트 계열의 SNCrW 소재를 사용하여 관성마찰 용접 방식으로 접합하여 제품을 제작하고, 접합부의 미세조직 관찰, 성분분석, 인장, 경도, 피로시험 등의 기계적, 금속적 특성평가를 통해 마찰용접제품에 대한 신뢰성을 확인하고 양산 생산을 위한 기술적 토대를 마련하였다.

• Journal of Welding and Joining
• /
• v.5 no.3
• /
• pp.19-27
• /
• 1987

This paper presents the weldability for cold pressure but welding method in junction of dissimilar metals each other. Although the weldability between the same aluminium metal plate welding has been studied, the study of itthe rod of aluminium and coper has not fully been investigated. The purpose is to suggest the optimal conditions on the rod of those under above method. To obtain the optimal conditions, associated experiments were performed in a various welding parameters. Consequently, it was proved that the mechanical properties such as tensile strength, hardness and bending strength could be obtained excellent particularly under the welding conditions; pressure is $(32~39) {\times} 10^3/kg/cm^2$, time is beyond 70 seconds, stage is higher than fifth stage.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.12
• /
• pp.3028-3044
• /
• 1993

A metallic bond of great strength for the same or dissimilar metals can be produced by the explosive welding. The formation of a metallic jet at the interface between the two impacting plates has been simulated using the numerical hydrocode DYNA2D. The mechanism of explosive welding for the wave formation is also analyzed by the computer simulation technique. The microscopic with the experimentally observed behaviour of the explosive welding. The computer simulations of the explosive welding process have proven especially useful for analyzing the mechanism of metallic bones.