• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.13 no.4
• /
• pp.99-105
• /
• 2014

The domestic airline industry undertakes the production of finished products by assembling existing self-described components via a design process which involves assembly and production steps, after which many of the finished products are exported. However, high reliability and stability must be guaranteed, because customers require high-precision components at the time of manufacturing. In the aircraft parts industry, the mass production of high-value-added parts is limited. Therefore, a small production scale depending on the part is used, as many types of conventional CNC lathe machines with X-axis and Z-axis as well as Z-axis and C-axis CNC milling are used. The parts also rely on high-pressure air to increase production. The most important factors are good stability during processing, as high-precision parts are required, as noted above. It was found that as the C-axis rotation speed increased, the diameter of the cutting tool decreased with a decrease in the surface roughness, while the workpiece rotation speed increased with an increase in the surface roughness.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.26 no.2
• /
• pp.118-124
• /
• 1990

The rope winder in addition to the line hauler was used for recoiling of the main line to the rope pond at the stern, however, catching the loops, evenly revoiling and arrangements of the loops were done manually by two men. The automatic loop catcher under the rope winder was consisted with the rotary lever, semicircle guide plates, transfer belt and swing rope receiver for arrangements of the loops and evenly recoiling. The obtained results are as follows: 1. The minor diameter of a loop and the diameter of the coiling pile in a lead core PP rope(ø 10mm) are about 14cm and 60cm while the rope is piled on the bottom. 2. Distribution ratio of the loops within upper or lower 10cm from the transfer belt is 93% with a lead sinker and 98% without sinker using by the smaller loop catcher. 3. The relationship between revolutions of the rotary lever N sub(1) (rpm) and the hauling pulley N sub(p) (rpm) by gear ratio 3:1 in the smaller loop catcher is as follows: N sub(p) =2.86 N sub(1) +23.74 and optimum ratio of horizontal speed of the loops by the rotary lever to hauling speed is about 70%. 4. The rope receiver is swung front and rear for the evenly recoiling and its period can be controlled by gear ratio or hydraulic circuit in accordance with the interval of the loops.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.10
• /
• pp.3633-3640
• /
• 2010

For a development of non-contact magnet gear which is magnetized as a helical shape, a method of 3-dimensional FEM analysis is used. An elementary technique required for magnetic property analysis and parts design about magnet gear is ensured. In order to test a performance of clean conveyor and turning device which is composed with magnet gear, a clean class 10 environment booth is used for a trial test. It is verified that the magnet conveyor can be acceptable under a condition of clean class 10 by a result of trial test about transfer speed, maximum torque permission, cleanness, maximum transfer weight, existence of hunting and degree of noise.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.11
• /
• pp.7-12
• /
• 2019

Generally, end effectors for automatic robots can use ceramics such as alumina(Al₂O₃) and silicon carbide(SiC). In this study, black alumina was developed and used in the semiconductor field through powder molding press forming. The black alumina can be mass produced.Alumina and black alumina were ground using a plane grinder to apply to the end effector of an automatic robot. The optimal cutting conditionswere found by analyzing the surface roughness(Ra) of black alumina through grinding. The alumina surface roughness is the feed rate was about 0.72 mm/sec, and the number of revolutions was best at 0.4879 ㎛ at 1700 rpm. In addition, the black alumina surface roughness shows a precision of less than 0.2 ㎛ in most cutting conditions. The feed rate was about 0.72 mm/sec, and the number of revolutions was best at 0.1361 ㎛ at 1900 rpm. The surface roughness of black alumina was better than that of alumina by about 0.35 to 0.47 ㎛.

• Journal of Korea Soil Environment Society
• /
• v.3 no.3
• /
• pp.109-116
• /
• 1998

Treatability tests of a soil washing device were performed for the remediation of eil-contaminated soil. The contaminant-containing soil with water was first fed into a oc-current screw conveyor and then into a counter-current washer. Surfactant was introduced into the washer and feeding soil was continuously separated on the basis of #40 mesh at the same time. A washing efficiency of 97.9% was achieved by the the soil washing device optimized.

• Proceedings of the KIEE Conference
• /
• 2003.10b
• /
• pp.171-173
• /
• 2003

기존의 선형 이송 시스템은 구동원으로 서보모터를 사용하고 있다. 서보 모터의 회전 운동을 직선운동으로 변환하기 위해서는 기계적인 동력전달 장치가 필요하며, 이는 위치 오차의 발생이나 주기적인 시스템의 유지보수의 필요성 등의 문제점을 야기한다. 본 논문에서는 단위 체적당 추력비가 기존의 모터에 비해 우수한 횡축형 선형전동기를 이용하여 LCD 공정에 사용되는 indexer 시스템의 선형 추진부에 적용하는 연구를 수행하였다. 실험결과 횡축형 선형전동기는 가속능력 최대 속도 및 위치결정 정밀도 등에서 indexer 시스템에 적용하기에 적합한 것을 검증하였다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.05a
• /
• pp.740-744
• /
• 2002

This paper describes the design and development of drills with deburring inserts. The drills can be used to drill holes and deburr the edges of the drilled holes simultaneously. The drills incorporate deburring inserts within the shank. The insert consists of a fixing base, a cantilever spring and a cutting tip. The stiffness of the cantilever spring and the details of the cutting tip play a central role for the successful deburring performance. The deburring performance is also governed by the conditions of the drilling burr best described by the burr control chart suggested by Dornfeld. With careful burr control, successful deburring is obtained by the drills with deburring inserts.

• 기계와재료
• /
• v.24 no.2
• /
• pp.96-109
• /
• 2012

채터진동은 공작기계에서 가공중에 소재와 공구사이에 나타나는 급격한 상대진동을 말한다. 이러한 진동은 가공 소재 품질에 심각한 영향을 미치는 요소일 뿐만 아니라 가공툴과 기계에 손상을 유발시키는 인자이기도 하다. 본 연구는 공작기계의 구동 중 발생되는 채터진동을 실시간으로 감지하여 공구의 회전속도와 이송 속도를 제어하여 자율보정함으로써 보다 빨리 채터진동의 영향을 보상함을 물론 보다 정밀한 가공물을 생산할 수 있는 채터진동 감지 및 보정에 관한 것이다. 실시간 처리를 위하여 본 연구에서의 공작기계의 채터진동 보상장치는 공작기계에 임베디드 형태의 디바이스로 개발되었으며, 구성은 공작기계의 채터진동을 감지하는 센서와 센서로부터 감지된 채터진동에 따라 보상값을 예측하여 산출하는 채터보상기를 포함하여 공작기계의 CNC제어기의 연계 구성됨을 특징으로 한다.

• Journal of Auto-vehicle Safety Association
• /
• v.4 no.1
• /
• pp.23-26
• /
• 2012

본 논문은 듀얼클러치 변속기 변속 메커니즘 개발을 위한 동역학적 시뮬레이션 해석 및 피로수명 해석에 관한 연구이다. 캠을 이용한 쉬프트 포크의 이송으로 기어를 변속하는 개념을 갖는 쉬프트 메커니즘의 작동성 및 설계안 검증을 위해 캠의 회전 속도, 접촉면의 경계조건 및 싱크로나이저 슬리브에서의 저항을 반영한 모델링을 구성하여 동역학적 시뮬레이션을 실시하였다. 각 파트의 응력 및 변형률 발생을 해석하여 설계 개선안을 도출하고, 개선안이 반영된 최종 시작모델의 시뮬레이션 상 최대 응력 발생 시점에서 시프트 포크의 각 접촉면 별 외력 작용을 분석하여 이를 적용한 피로 해석을 진행하였다.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.04a
• /
• pp.497-500
• /
• 2000

절삭 작업과정에서 발생하는 버는 공구와 피삭재가 만나는 상태에 따라 그 형상이 결정되어진다. 공구와 피삭재 사이의 각, 공구의 회전속도, 이송속도, 피삭재의 종류등은 이러한 버의 형상을 결정하는데 결정적인 역할을 하므로, 실험에 의해서 생성된 단계별 자료를 CAD 및 CAM 데이터와 연관시켜 효율적인 알고리즘을 만들고자 한다. 특별히 공장자동화에 따른 작업의 자동화뿐 아니라 관리 체계의 정립을 위하여 전문가 시스템의 도입 역시 시급히 요구되고 있는 실정이다. 여기서 CAD 데이터는 피삭재에 대한 특징 형상의 정보를 포함하고 있기 때문에 피삭재의 형상에 대한 정보를 얻을 수 있다. 인식된 형상에 대하여 Exit 버 형성시 접점과 Exit Angle을 계산하기 위해 도형의 방향인식이 필요하며, 이를 통해 공구와 피삭재와의 관계를 산출하여 Exit 버의 판별을 수행할 수 있다. 본 논문에서는 이러한 과정을 수행하는 프로그램을 개발한다.