• The Journal of the Acoustical Society of Korea
• /
• v.32 no.4
• /
• pp.317-328
• /
• 2013

In this paper, the optimization has been performed to design a multi-layer structure that is used as a structure for noise reduction of acoustic sonar sensors in underwater vehicles. Two design goals are considered to reduce self-noise from own machineries and to enhance acoustic signals detected from outside. Both distinct and continuous design parameters have been used such as selection of material properties of each layer and thickness of each layer, respectively. The sensitivity of design parameters has been analyzed and the evolutionary algorithm has been implemented for design optimization. For design optimization process, each of the design goals and the two combined design goals have been considered to analyze the achievement of those design goals.

• Journal of Korea Society of Industrial Information Systems
• /
• v.7 no.4
• /
• pp.83-89
• /
• 2002

Oil ring and sound proof rubbers are very much important because the cause of oil leakage are mostly occupied by these rubbers. So good oil rings are the necessary parts of autolife expansion. The expensive selection system keeps from factory automation and most works are established manually. These study has been the basis of test equipments automatically in rubber products and DCT algorithm has been applied and the selection system is made efficiently differentiating good or poor.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2021.11a
• /
• pp.148-151
• /
• 2021

본 논문은 oneM2M을 활용하여 스마트시티의 일환으로 사회적 이슈가 되고 있는 미세먼지(PM10, PM2.5) 측정 플랫폼을 설계하였다. 미세먼지 측정 디바이스를 이동식 차량에 부착하여 미세먼지가 측정이 되고 있지 않은 사각지대까지 범위를 넓혀 측정하였다. 또한 미세먼지뿐만 아니라 일상생활과 연관된 온도, 습도, 대기압, 휘발성 유기화합물(VOC), 일산화탄소(CO), 아황산가스(SO₂), 이산화질소(NO₂), 소음을 센서의 응답 시간에 따라 최소 10초 간격으로 수집하였다. 수집된 정보들은 미세먼지 측정 디바이스 기준으로 반경 1km내 격자모양으로 지형 화면에 실시간으로 표시하고 모니터링함으로서 동작성을 확인하였다.

• The Journal of the Acoustical Society of Korea
• /
• v.38 no.5
• /
• pp.543-548
• /
• 2019

The tonal signal caused by the machinery component of a vessel such as an engine, gearbox, and support elements, can be modeled as a sparse signal in the frequency domain. Recently, compressive sensing based techniques that recover an original signal using a small number of measurements in a short period of time, have been applied for the tonal frequency detection. These techniques, however, cannot avoid a basis mismatch error caused by the discretization of the frequency domain. In this paper, we propose a method to detect the tonal frequency with a small number of measurements in the continuous domain by using the atomic norm minimization technique. From the simulation results, we demonstrate that the proposed technique outperforms conventional methods in terms of the exact recovery ratio and mean square error.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.9
• /
• pp.1157-1164
• /
• 2001

Centrifugal fans are widely used and the noise generated by these machines causes one of the most serious problems. In general, the centrifugal fan noise is often dominated by tones at BPF(blade passage frequency) and its higher harmonics. This is a consequence of the strong interaction between the flow discharged from the impeller and the cutoff in the casing. However, only a few research have been carried out on predicting the noise because of the difficulty in obtaining detailed information about the flow field and casing effects on noise radiation. The objective of this study is to understand the generation mechanism of sound and to develop a prediction method for the unsteady flow field and the acoustic pressure field of a centrifugal fan. We assume that the impeller rotates with a constant angular velocity and the flow field of the impeller is incompressible and inviscid. So, a discrete vortex method(DVM) is used to model the centrifugal fan and to calculate the flow field. The force of each element on the blade is calculated by the unsteady Bernoulli equation. Lowsons method is used to predict the acoustic source. In order to compare the experimental data, a centrifugal impeller and wedge introduced by Weidemann are used in the numerical calculation and the results are compared with the experimental data. Reasonable results are obtained not only for the peak frequencies but also for the amplitudes of the tonal.

• Explosives and Blasting
• /
• v.27 no.1
• /
• pp.47-52
• /
• 2009

Blasting is necessary for excavation processes since more than 70% of korean land is consist of mountains. The vibration and noise accompanied by blasting processes usually bring about public complaints. Blasting patterns are chosen by economical efficiency, stability and construction conveniency. However, there are many alternatives without control to settle the popular complaint. To prevent those alternatives, standard blasting method for design and construction were suggested by MLTM (Ministry of Land, Transport and Maritime Affairs) in 2006. However, standard blasting pattern of MLTM was designed in a lump irrespective of types of rocks. Economical loss may occur by ignoring the characteristics of rocks for the applications to the rocks with low intensity, such as shale, or containing many joint. We deduced some economical progresses by performing test blasting with adjusted drilling spacing and length of burden considering the characteristics of local rock. This paper suggests the start of case studies for different applications. Economic improvement can be expected by applying those results deduced from case studies to design and construction.

• Journal of Platform Technology
• /
• v.9 no.4
• /
• pp.79-89
• /
• 2021

In this paper, the fine dust (PM10) and ultrafine dust (PM2.5) measurement platforms are designed to be mobile and fixed using oneM2M, the international standard for IoT. The fine dust measurement platform is composed and designed with a fine dust measurement device, agent, oneM2M platform, oneM2M IPE, and monitoring system. The main difference between mobile and fixed is that the mobile uses the MQTT protocol for interconnection between devices and services without blind spots based on LTE connection, and the fixed uses the LoRaWAN protocol with low power and wide communication range. Not only fine dust, but also temperature, humidity, atmospheric pressure, volatile organic compounds (VOC), carbon monoxide (CO), sulfur dioxide (SO2), nitrogen dioxide (NO2), and noise data related to daily life were collected. The collected sensor values were managed using the common API provided by oneM2M through the agent and oneM2M IPE, and it was designed into four resource types: AE and container. Six functions of operability, flexibility, convenience, safety, reusability, and scalability were analyzed through the fine dust measurement platform design.

• Journal of the Korean Society for Railway
• /
• v.15 no.5
• /
• pp.485-497
• /
• 2012

Recently, with increasing social interests on noise and vibration induced by railway traffic, the application of floating slab track that can efficiently reduce the railway vibration is increasing. In this study, to more accurately understand the dynamic behavior of the floating slab track, a laboratory mock-up test has been performed, and the static and dynamic behaviors at frequency range near the system resonance frequency were explored. Based on the test results, the design of the floating slab track and the structural analysis model used in the design have been verified. The analytic and test results demonstrate that the dominant frequency of the floating slab track occurs at the frequencies between vertical rigid body mode natural frequency and bending mode natural frequency, and the dominant deformation mode is close to the bending mode. This suggests that in the design of the floating slab track, the bending rigidity of the slab and the boundary conditions at slab joints and slab ends should be taken into consideration. Also, the analytic results by the two-dimensional finite element analysis model using Kelvin-Voigt model, such as static and dynamic deflections and force transmissibility, are found in good agreement with the test results, and thus the model used in this study has shown the reliability suitable to be utilized in the design of the floating slab track.