• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.11 s.102
• /
• pp.1114-1122
• /
• 2005

In this paper, the study of a design, fabrication and measurement of the receiver MMIC LNA, mixer for S-band application is described. The LNA is designed by 2-stage common source. The mixer is composed of active LO and RF balun to integrate on a chip and applied a newly proposed bias circuit to compensate the process variations of active devices. The LNA has 15.51 dB-gain and 1.02dB-Noise Figure at 2.1 GHz. The conversion gain of the mixer is -12 dB, IIP3 is approximately 4.25 dBm and port-to-port isolation is over 25 dB. The newly proposed bias circuit is composed of a few FETs and resistors, and can compensate the variation of the threshold voltage by the process variations, temperature changes and etc. The designed chip size is $1.2[mm]\times1.4[mm]$.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.6
• /
• pp.504-511
• /
• 2016

In this paper, the method is proposed that the equivalent result can be obtained by compensating the variation of gain and phase in the comparison with the result of near-field measurement which is obtained in the steady state, although the gain and phase variation of rx-channels occurred in the near-field rx-measurement of digital active phased array antenna. The proposed concept has the time section for monitoring the state of the rx-channels through the calibration path in the measurement timeline, and is the method for compensating the variation of state. For validating the proposed method, the fabricated X-band digital active phased array antenna and the planar near-field measurement facility is utilized. The proposed method is validated in the comparison with the compensated pattern which the unstable state of rx-channels is calibrated and the reference pattern obtained under the steady state of the rx-channels.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.4
• /
• pp.413-420
• /
• 2003

In this paper, the correction method of antenna beam direction errors is introduced which caused by frequency scan effect in active Phased may antenna for satellite communications. The antenna makes the beam directional error from frequency scan effect when it has dual beam may structure with asymmetrical series connection, their frequencies are different and for from each other, their 3dB beamwidth is narrow, and scan range is wide. By proposed equations, estimated beam direction error angles can be calculated and active phase shifter control values also can be calculated to compensate them. In this paper, the active phased array antenna system was fabricated to measure beam direction errors both before and after correction, which has dual beam from 32${\times}$4 main level array and 4${\times}$2 second level array, frequency deviation 500 MHz max.(6.7 %) at 7.25 GHz∼7.75 GHz ranges, 0$^{\circ}$∼${\pm}$35$^{\circ}$nm ranges, and 35.6 dBi gain with 2.2$^{\circ}$3 dB beam width. Its beam direction error by frequency san effect which was 2.5$^{\circ}$max., was reduced to 0.2$^{\circ}$max. after correction. This was 7 dB improvement of signal loss. The active phased array antenna can accurately track the target satellite for communications by this proposed correction method.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.5B
• /
• pp.517-529
• /
• 2011

In this paper, the parameters of the RTT (Radio Transmission Techniques) for SANET (Ship Ad-hoc NETwork), which is considered for the next generation maritime communication systems, are set up. A channel model has been analyzed based on the practical measured maritime wireless channel in VHF (Very-High Frequency) for SANET system. Also, by considering the frame structure including preamble, guard time and pilots for both single and multi-carrier systems, the BER (Bit Error Rate) performances are evaluated and analyzed in the aspects of channel compensation and channel coding techniques. Based on the simulation results, optimal modulation & coding schemes are suggested for SANET. That is, in single-carrier system by using differential modulation schemes, channel compensation is not necessary. However, channel coding is helpful to achieve additional gain. On the other hand, when 16-QAM modulation is employed in multi-carrier system, the implementation of both channel compensation and channel coding techniques show huge performance gain for various of K values, which are related to different maritime environments, and the rolling effects of wave.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.11
• /
• pp.978-986
• /
• 2016

X-band phased array antenna module for the compensation of deformed beam direction by wing deformation is designed and fabricated. The phased array antenna module consists of array antenna, phase shifter, power divider and control circuit. To select out the best component, the variation of radiation pattern by wing bending and phase error of components is simulated. The fabricated phased array antenna module shows an antenna gain of 5.84 dBi, a return loss of 13.6 dB and a bandwidth of 10.6 % at 9.375 GHz. The test bed was set up to verify the performance of beam direction compensation. This test confirmed that the main beam direction of array antenna has been well restored under wing bending of 9 %.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.12
• /
• pp.29-35
• /
• 2008

In this paper, The author present a load current feed-forward compensator by method that improve voltage controller of Step-down Chopper to get stable output voltage to sudden change of load current. To confirm the characteristics of a presented load current feed-forward compensator compared each transfer function of whole system that load current feed-forward compensator is added with transfer function of whole system that existent voltage controller is included using Mason gains formula in Root locus and Bode diagram. As a result the pole of system is improved, extreme point of the wave and system improves, and size of peak value and phase margin of break frequency in resonance frequency confirmed that is good. Therefore, presented control technique could confirm that reduce influence by perturbation and improves stationary state and dynamic characteristics in output of Step-down Chopper.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.3 no.3
• /
• pp.517-531
• /
• 1999

This paper presents the development of the 2-mode variable gain high power amplifier for a transmitter of INMARSAT-M operating at L-band(1626.5-1646.5 MHz). This SSPA(Solid State Power Amplifier) is amplified 42 dBm in high power mode and 36 dBm in low power mode for INMARSAT-M. The allowable error sets +1 dBm of an upper limit and -2 dBm of a lower limit, respectively. To simplify the fabrication process, the whole system is designed by two parts composed of a driving amplifier and a high power amplifier, The HP's MGA-64135 and Motorola's MRF-6401 are used for driving amplifier, and the ERICSSON's PTE-10114 and PTF-10021 are used the high power amplifier. The SSPA was fabricated by the circuits of RF, temperature compensation and 2-mode gain control circuit in aluminum housing. The gain control method was proposed by controlling the voltage for the 2-mode. In addition, It has been experimentally verified that the gain is controlled for single tone signal as well as two tone signals. The realized SSPA has 42 dB and 36 dB for small signal gain within 20 MHz bandwidth, and the VSWR of input and output port is less than 1.5:1 The minimum value of the 1 dB compression point gets 5 dBm for 2-mode variable gain high power amplifier. A typical two tone intermodulation point has 32.5 dBc maximum which is single carrier backed off 3 dB from 1 dB compression point. The maximum output power of 43 dBm was achieved at the 1636.5 MHz. These results reveal a high power of 20 Watt, which was the design target.the design target.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.16 no.3
• /
• pp.34-40
• /
• 2012

A pressure control law to regulate pressure of gas generator is suggested. To design a model based control law, the governing equation which consists of Robert and conservation equation is built and verified through the ground burning test. PID and nonlinear adaptive control laws are designed to analyze the loop response characteristics under the system which has varying eigen properties arisen from combustion volume change. It is suggested that new approach, gain scheduling design, is required to overcome the defects identified from numerical simulation results of the two control laws. The newly suggested scheme shows good control performance even under disturbances and measurement noise.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.24 no.7B
• /
• pp.1370-1377
• /
• 1999

A technique for an efficient video coding based on characteristics of human visual response in relation to motion is described in this paper. An input frame is segmented into low frequency bands and high frequency bands by wavelet transformation. The non-sensitivity parts of the segmented bands are removed according to spatial and directional frequency sensitivity, which is related to motion property in a frame. Experimental results of the proposed method show good performance in PSNR with keeping on without degradation of subjective quality with 21-30:1 coding rate.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.618-623
• /
• 2011

A pressure control law to regulate pressure of gas generator is suggested. To design a model based control law, the governing equation which is consisted of Robert and conservation equation is built and verified through the ground burning test. PID and nonlinear adaptive control laws are designed to evaluate the loop response characteristics under the system which has varying eigen properties as combustor volume is increased. It is suggested that new approach, gain scheduling design, is required to overcome the defects identified from numerical simulation results of the two control laws. The newly suggested scheme showed good control performance even under disturbances and measurement noise.