• Title/Summary/Keyword: 응축부

Search Result 110, Processing Time 0.029 seconds

생쥐의 초기 미란성위궤양 상피세포의 미세구조 변화 및 분비면역계에 대한 연구

  • Ha, Mi-Hye;Choe, Eun-Sang;Ha, Jae-Cheong
    • The Korean Journal of Zoology
    • /
    • v.35 no.1
    • /
    • pp.45-57
    • /
    • 1992
  • 생쥐를 48시간 동안 결식시킨 후 유문결찰하여 급성미란을 유발시키고 미란형성부의 점막 내위선을 구성하는 각 세포의 구조변화와 IgA 분비세포의 분포를 관찰하였다. 미란부 점액분포의 변화는 표면상피의 손상 정도가 심해질수록 경계부의 PAS양성반응은 감소되었으며 중심부에서는 표면상피의 소실로 인하여 PAS 양성반응이 관찰되지 않았다. Glycocalyx 관찰을 위한 ruthenium red 반응에서도 경계부의 상피세포 손상이 심해짐에 따라 정단세포막 상층에 나타나는 양성반응은 감소되었고 측면과 기저면의 양성반응은 관찰되지 않은 것으로 보아 세포 손상시 tight junction은 파괴되지 않음을 알 수 있었다. 미란경계부의 미세구조변화로서, 상피세포는 손상이 진행될수록 세포질이 용해되어 공포가 형성되고 핵응축 및 정 단세포질의 점액원과립의 소실이 관찰되었으나 tight junction은 유지되었다. 반면에 점액경세포는 점액원과립의 수가 증가되고 조면소포체가 종창되어 있었다. 미란의 경계부와 중심부에서 벽세포는 다수의 소포가 출현한 후 세포내세관이 종창되었으며 그 후에 mitochondria가 파괴되었고 주세포는 주변의 벽세포가 커지면서 가장자리로 밀려나 크기가 정상보다 작아지고 조면소포체와 mitochondria가 종창을 나타내었다. IgA분비세포는 점막이 파괴된 미란부 점막하조직의 혈관 주변에 다수 존재하는 형질세포에서 확인되었다.

  • PDF

Separate type heat pipe performance comparison by the heat exchanger shapes (열교환기 형상에 따른 분리형 히트파이프 성능 비교)

  • Jeon, Sung-Taek;Cho, Jin-Pyo
    • Journal of the Korea Academia-Industrial cooperation Society
    • /
    • v.17 no.12
    • /
    • pp.723-729
    • /
    • 2016
  • This study compared fin-tube and parallel-flow heat pipes for their sensible heat exchange rate, heat recovery amount, and air-side pressure drop. Tests were done with different refrigerant charging rates of 40-60% vol. and air flow rates of 300-1,400. The sensible heat exchange rate was highest for both types of heat pipes at a working fluid charge of 40% vol. and low flow rate. For the parallel-flow heat pipe, the 60% vol. charge is too high and results in a low sensible heat exchange rate. The reason is that the thicker liquid film of the tube wall deteriorates the heat transfer effect. Hence, the optimal charging rate is 40 to 50% vol. The evaporator heat pipe has a larger air-side pressure drop than the condenser section heat pipe. The reason is considered to be condensation water arising from the evaporator surface. Compared to the fin-tube heat pipe, the parallel-flow heat pipe showed better performance with a working fluid charging rate of 48%, volume of 41%, and an air-side pressure drop about 37%.

Evaluation of Concentration Polarization at Feed in the Permeation of VOCs/$N_2$ mixtures through PDMS membrane (VOCs/질소 혼합물 증기투과시 공급액부 경계층에서의 농도분극 분석을 위한 모델식 확립)

  • 염충균;이상학;최정환;이정민
    • Membrane Journal
    • /
    • v.11 no.2
    • /
    • pp.74-82
    • /
    • 2001
  • By using a phenomenological approach, model equations incorporating the resistance-in¬series concept were established to evaluate quantitatively concentration polarization in the boundary layer in feed adjacent to the membrane surface in the vapor permeation and separation of volatile organic compounds (VOCS)/$N_2$ mixture through po]y(dimethylsiloxane) (PDMS) membrane. The vapor permeations of various VOCS/$N_2$ mixtures through PDMS membrane were carried out at various feed flow rates. Chlorinated hydrocarbons, such as, methylene chloride, chlorofonn, 1,2-clichloroethane and 1,1,2-trichloroethane were used as organic vapor. By fitting the model equations to the experimental penneation data. the model parameters were detennined. respectively. Both the mass transfer coefficient of VOC across tbe boundary layer and concentration polarization modulus as a measure of the extent of concentration polarization were eitimated Quantitatively by the mooe1 equations with the determined model parameters. From the analysis on the detennined model parameters, the boundary layer resistance due to the concentration polarization of VOCs component was found to be more significant when the condensability of voe was greater. This study seeks to emphasize the importance of the boundary resistance on the vapor penneation of the vapor/gas mixtures with high permeability and high selectivity towards the minor component VOC.

  • PDF

Fine Structure of the Epithelial Apoptosis in the Anuran Tadpole Rana nigromaculata (참개구리(Rana nigromaculata) 유생기 상피 세포사의 미세구조)

  • Lee, Hye-Won;Moon, Myung-Jin
    • Applied Microscopy
    • /
    • v.40 no.2
    • /
    • pp.81-88
    • /
    • 2010
  • The fine structural characteristics of the apoptotic cells in the cutaneous epithelium of the anuran tadpole of the black-spotted frog, Rana nigromaculata was examined using the TUNEL (Terminal deoxynucleotidyl transferase-mediated biotinylated d-Uridine triphosphate Nick End Labeling) staining technique and TEM (transmission electron microscopy) observations. The cutaneous epithelium of the tadpole was composed of stratified cuboidal cells and the apoptotic cell death was observed continuously during the tail degeneration stages from the Shumway stage number 31 to 33. The early apoptotic cells shown in the epithelium demonstrated condensation and margination of the chromatin material at the nuclear periphery, and nuclear breakdown and cytoplasmic condensation were followed. Subsequent cytoplasmic degeneration of the apoptotic cell were produced by membrane-bounded cell fragments with relatively well preserved organelles. Following the processes of autophagic degradation, the late apoptotic cells being phagocytosed by other surrounding cells. These nearby cells, presumptive intraepithelial macrophages, contain a variety of lysosomal residual bodies which fuses with other cell organelles or other cytoplasmatic material to form secondary lysosomes. They are soon transformed into lamellar shaped vesicles and finally disappeared during the process of degradation.

Performance of a Latent Heat Storage System Using Two-Phase Closed Thermosyphon(I) - the Case of Constant Heat Input - (열싸이폰을 이용한 잠열축열시스템의 성능실험(I) - 열주입량이 일정한 경우 -)

  • Kim, Tae-Il;Kim, Ki-Hyun
    • Solar Energy
    • /
    • v.12 no.3
    • /
    • pp.28-36
    • /
    • 1992
  • The performance of a latent heat storage system using a thermosyphon as the heat transfer device between the heat source and the phase change material was investigated experimentally. In order to increase the effective conductivity of the phase change material, layers of copper wire mesh were immersed in the paraffin wax(Sunoco P-116) in such a way that they also may be considered as fins of the thermosyphon. The important results are as follows : (1) The void space of the wire mesh allowed the convection to occur, thus enhanced the performance of the system : (2) The increase of the number of layer of wire mesh increased the conduction heat transfer. However, it also had adverse effect of subduing convective motion of liquid wax : and (3) Overall heat transfer coefficient and thermosyphon conductance increased with the increase of the number of layer of wire mesh, whereas the heat transfer coefficient between the thermosyphon and the wax decreased.

  • PDF

Condensation Heat Transfer of R32 and R454B Inside a Microfin Tube as an Alternative Refrigerant to R410A (R410A 대체냉매 R32와 R454B의 미세핀 관내 응축 열전달)

  • KARAGEORGIS, ANDREAS;HINOPOULOS, GEORGE;KIM, MAN-HOE
    • Transactions of the Korean hydrogen and new energy society
    • /
    • v.33 no.4
    • /
    • pp.413-418
    • /
    • 2022
  • This paper presents two-phase condensation heat transfer and pressure drop characteristics of R32 and R454B as an alternative refrigerant to R410A in a 9.52 mm OD microfin tube. The test facility has a straight, horizontal test section with an active length of 2.0 m and is cooled by cold water circulated in a surrounding annular space. The heat transfer coefficients of the annular space were obtained using the modified Wilson plot method. Average condensation heat transfer coefficient and pressure drop data are presented at the condensation temperature of 35℃ for the range of mass flux 100-400 kg/m2s. The average condensation heat transfer coefficients of R32 refrigerant are 35-47% higher than R410A at the mass flux considered in the study, while R454B data are similar to R410A. The average pressure drop of R32 and R454B are much higher than R410A and they are 134-224% and 151-215% of R410A, respectively. R32 and R454B have relatively low GWP and high heat transfer characteristics, so they are suitable as alternatives for R410A.

Fabrication and Test Results of Superconducting Magnet for Crystal Growing System (실리콘 웨이퍼 성장용 초전도 마그네트의 제작 및 성능평가)

  • Sim, K.D;Choi, S.J.;Kim, K.H.;Han, H.H.;Kim, H.J.;Jin, H.B.;Lee, B.K.;Kwon, Y.K.
    • Proceedings of the KIEE Conference
    • /
    • 2002.07b
    • /
    • pp.824-827
    • /
    • 2002
  • 12inch 이상의 웨이퍼 성장에는 실리콘 용탕의 대류를 억제하여 웨이퍼의 순도를 높이기 위해 자기장 특히, 웨이퍼의 성장방향에 수직인 '수평자장'을 인가하는 방법이 사용된다. 현재 '자기장인가 방식', 특히 초전도를 사용한 자장인가 방식이 직경 1600mm에 이르는 용탕의 용액을 제어하는 유일한 방법으로 받아들여지고 있다. 본 논문에서는 12inch 실리콘 웨이퍼 성장용 초전도 마그네트 개발의 전단계로 개발중인 8inch 웨이퍼 성장용 수평자장형 초전도마그네트의 제작과정과 성능평가 결과에 대해 다루었다. 본 연구를 통해 액체헬륨의 증발을 최소화하기 위한 재응축형 극저온 용기에 대한 기술이 개발 되었으며, diode를 이용한 ��치보호부, HTS 전류리드의 ��치 protection부 등의 부속기술이 개발되었다. 초전도 마그네트는 내경 1400mm의 saddle type으로 이의 제작에 있어 많은 기술적 난재들을 경험해야 했다. 전체 시스템에 대한 성능평가 결과, 극저온용기 및 부속장치에 대한 결과는 만족스러웠으나, 코일부의 성능은 계획한 목표에 미치지 못했다.

  • PDF

A Study on Boiling Characteristics of Direct Contact LNG Evaporator (직접접촉식 액화천연가스 기화기의 비등특성 연구)

  • 김남진;김종보
    • Journal of Energy Engineering
    • /
    • v.4 no.3
    • /
    • pp.420-428
    • /
    • 1995
  • 현재 사용하고 있는 액화천연가스 기화기는 관내부로 -162$^{\circ}C$의 액화가스가 흐르고, 관외부로 발전소 증기응축기 출구에서 배출된 20~3$0^{\circ}C$의 해수를 흐르도록 하여, 두 유체사이의 온도차로 기화시키는 간접접촉방식 열교환기가 사용되고 있다. 그러나 간접접촉방식 열교환기는 두 유체사이의 큰 온도차로 인한 금속재료의 피로현상과 해수의 염분에 의한 재질의 부식 및 미생물 부착 등의 원인으로 열전달효율이 저하되고 있다. 따라서 본 연구는 관을 중간매체로 하는 간접접촉식 열교환기대신 액화천연가스와 기화용수인 물을 직접접촉시키는 방법으로 이용하여, 위와 같은 문제점들을 근본적으로 해결하려 한다. 본 실험에서는 기화기내의 수위 500 mm와 물의 유량 10 l/min을 일정하게 고정시키고, 액화천연가스의 유량 0.12 ㅣ/min, 0.36 l/min, 0.6 l/min, 기화기내의 압력을 100 kPa, 300 kPa, 500kPa로 변화시키면서 기화기내의 기포, 온도분포, 급팽창현상, 동결현상 및 기화후 수분함유량등의 비등특성을 규명하였다. 실험결과 기화기내의 압력이 증가할수록 기포는 작고 균일한 분포를 이루고, 폭발적인 급팽창현상은 일어나지 않았다. 또한 동결현상은 액화천연가스의 기화를 방지하지 못하였으며, 기화된 천연가스내의 수분함유량 몰%는 압력과 유량이 증가함에 따라 감소하는 경향을 보이고 있다.

  • PDF

A Study on Operating Characteristics and Development of Woven-Wired Wick Heat Pipe (편조 윅 히트파이프의 개발과 작동특성에 관한 연구)

  • Moon, Seok-Hwan;Choi, Choon-Gi;Hwang, Gunn;Choy, Tae-Goo
    • Journal of Energy Engineering
    • /
    • v.9 no.1
    • /
    • pp.54-59
    • /
    • 2000
  • 전자부품 및 시스템의 고속/고밀도화 추세에 따라 발열밀도가 계속증가하고 있다. 최근 팬티엄 II 급이상의 노트북 컴퓨터의 CPU에서는 칩당 발열량이 10W 이상으로 증가하고 있고 패키징 공간의 제한 때문에 소형히트파이프를 이용한 냉각이 많이 적용되고 있다. 본 연구에서는 모세압구동력이 크고 생산성등이 고려된 편조 형태의 새로운 윅을 개발하였으며 , 노트북 컴퓨터의 CPU 등 소형 전자부품냉ㄱ가에 적용가능한 직경 3, 4 mm 히트파이프를 설계 및 제작하였다. 직경 3, 4 mm Miniature Heat Pipe (이하 MHP) 의 작동특성은 일반적인 중형히트파이프와 다르므로 MHP 의 열전달 특성 및 작동성능에 미치는 각종 인자들의 영향을 파악하고자 성능시험을 수행하였다. 고려된 작동인자로는 작동유체 충전률, 전체 파이프길이 및 증발부, 응축부길이, 설치 경사각, 윅의 가닥수, 열부하 등이다. 작동인자의 영향과 관련된 연구결과는 향후 패키징을 위한 응용연구의 기초자료로 활용할 수 있을 것이다.

  • PDF

A Study on the Effect of Non-Clean Water Treatment Chemicals for R-134a Turbo-Chiller Condensers (R-134a 터보냉동기 응축기의 무세정 수처리 약품 효과 연구)

  • JUNG, DA-WOON;KIM, MAN-HOE
    • Transactions of the Korean hydrogen and new energy society
    • /
    • v.33 no.4
    • /
    • pp.437-445
    • /
    • 2022
  • This paper presents an experimental study on the main management factors of the condenser contamination such as fouling and corrosion for the R-134a turbo-chiller to save energy, reduce corrosion rates, and reduce maintenance costs through the application of condenser non-cleaning water treatment chemical. The series of experiment is conducted using combining oxidative microbial sterilizers, non-oxidizing microbial sterilizers, and anti-corrosion agents. The leaving temperature difference and corrosion rates for three different combination of chemicals are collected and analyzed. The experimental results show that the cost reduction (4,066,000 Won/year) of the disinfectant (FT-830) can be achieved by adding the oxidative disinfectant (NaOCl) and the non-oxidizing disinfectant (NX-1116). The LTD value is maintained at 1.9℃, and the corrosion rates of copper and carbon steel specimens are 0.07 mpy and 1.61 mpy, respectively.