• Journal of Korean Society of Environmental Engineers
• /
• v.38 no.7
• /
• pp.371-376
• /
• 2016

In this study, the survey of bisphenol-A in indoor water service pipes rehabilitated with epoxy resin was conducted and the risk assessment was done to investigate the effect on the human health to drink tap water. Bisphenol-A in raw water was detected in a range of 50~118 ng/L in all samples, where the limit of quantification was 10 ng/L. This is caused by inflow of the sewage effluent or the tributaries of the surrounding area containing bisphenol-A. Bisphenol-A was not detected in finished water after the advanced water treatment process. It was achieved by its removal from the processes of flocculation-precipitation and oxidation of ozone and chlorine and by being changed to other by-product materials. For the indoor water service pipe, bisphenol-A was not detected in all cases which was not coated with epoxy resin. However, when epoxy resin is lined within the indoor water service pipe, bisphenol-A was identified at maximum level of 521 ng/L and was detected above the limit of quantitation at 68 percentages of all samples. The Hazard Quotient (HQ) at the maximum level (521 ng/L) of the detected bisphenol-A is 0.004, which is less than the reference value of 0.1 for the tap water intake. Therefore, it is considered that the detected levels of bisphenol-A in this study would be safe to drink tap water.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.10
• /
• pp.1123-1128
• /
• 2005

NIB(methylisoborneol) is an earthy/musty odor compound produced as a second metabolite by cyanobacteria and actinomycetes. MIB is not removed by conventional water treatment(coagulation, sedimentation, filtration) and its presence in tap water, even at low ng/L levels, can result in consumer complaints. PAC(powdered activated carbon) can effectively remove MIB when the correct dose is applied. But, since most operators in water treatment plants apply a PAC dose and then adjust that dose depending on direct observation (odor detection) after treatment, the result is often under-dose or eve,-dose. In this study, kinetic and isotherm tests using $^{14}C$-radiolabeled MIB were performed to determine coefficients for the HSDM(homogeneous surface diffusion model), including liquid film mass transfer coefficient($K_f$) and surface diffusion coefficient ($D_s$). The HSDM gave a reasonable fit and allowed prediction with the experimental data. Base on the HSDM, the authors developed an optimum PAC dose prediction program using the Excel spreadsheet. When the developed program was applied at two water treatment plants, the PAC dose based on the experience of operators in the water treatment plant was significantly different from that recommended by the newly developed program. If operators are willing to use the optimum PAC dose prediction program, it should solve dosing problems.

• Clean Technology
• /
• v.19 no.3
• /
• pp.300-305
• /
• 2013

Zinc oxide (ZnO) and reduced graphite oxide (rGO) composites were synthesized and tested as adsorbents for the hydrogen sulfide ($H_2S$) adsorption at mid-to-high (300 to $500^{\circ}C$) temperatures. In order to investigate the critical roles of oxygen containing functional groups, such as hydroxyl, epoxy and carboxyl groups, attached on rGO surface for the $H_2S$ adsorption, various characterization methods (TGA, XRD, FT-IR, SEM and XPS) were conducted. For the reduction process for graphite oxide (GO) to rGO, a microwave irradiation method was used, and it provided a mild reduction environment which can remain substantial amount of oxygen functional groups on rGO surface. Those functional groups were anchoring and holding nano-sized ZnO onto the 2D rGO surface; and it prevented the aggregation effect on the ZnO particles even at high temperature ranges. Therefore, the $H_2S$ adsorption capacity had been increased about 3.5 times than the pure ZnO.

• Korean Chemical Engineering Research
• /
• v.54 no.6
• /
• pp.786-791
• /
• 2016

Spherical graphene balls were fabricated by an aerosol spray drying process after reduced graphene oxide was prepared by the liquid phase reaction using glucose as an environment-friendly reducing agent. Spherical morphology of the as-fabricated particles was observed by FE-SEM analysis. Diffraction patterns of spherical particles were found as graphene by XRD analysis. Sphericity of GB was controlled by the variation of operating temperature, amount of glucose, and addition of $NH_4OH$. Higher sphericity of GB was prepared at higher operating temperature in the presence of $NH_4OH$. As the amount of glucose in the liquid phase reaction increased in the presence of $NH_4OH$, sphericity of GB increased. The highest sphericity of GB was 1.1. GB of higher sphericity showed lower aggregation property than that of lower sphericity. Furthermore, as-prepared GBs were found as a potential electrode material for capacitor.

• Journal of the Korean Ceramic Society
• /
• v.41 no.4
• /
• pp.284-288
• /
• 2004

To improve mechanical properties of $Al_2$O$_3$/ZrO$_2$composites have been controlled dispersion of ultra low size ZrO$_2$ particles in $Al_2$O$_3$ ceramics by polymeric precursor method (Pechini process). In case of coprecipitation or mechanical mixing of ZrO$_2$ powders with $Al_2$O$_3$, homogeneous dispersion and controlling the ZrO$_2$ size were relatively difficult due to high sintering temperature. So the polyesterization process of Zr/Y(NO$_3$)$_3$-citric acid solution in ethylene glycol with the commercial sub-micron sized o(-alumina powder (Sumitomo AES-11(0.4 ${\mu}{\textrm}{m}$)) was adopted in order to obtain homogeneous dispersion of ZrO$_2$ in A1203. By this partial polyesterization process, the homogeneous dispersion of relatively low sized ZrO$_2$in $Al_2$O$_3$/ZrO$_2$composites was achieved at 1450∼1$600^{\circ}C$ of sintering temperature range and their mechanical properties were measured.

• Culinary science and hospitality research
• /
• v.20 no.6
• /
• pp.245-253
• /
• 2014

The objectives of this study were to investigate the quality characteristics of nutritional cereal bars with various concentrations (0, 5, 10, 15, 20%) of Citrus fruit extract. Regarding the color of nutritional cereal bars, the L value decreased according to the amount of nutritional cereal bars added, whereas a, b color values increased. The nutritional cereal bar with 5, 10, 15, and 20% Citrus fruit extract had a significantly lower hardness value than the control nutritional cereal bar. The result of a sensory test showed that the scores for color, taste, texture, and overall acceptability were the highest for the nutritional cereal bar with 15% Citrus fruit extract. The nutritional cereal bar with 20% Citrus fruit extract attained the highest flavor score. The results indicated that optimal concentration of Citrus fruit extract in nutritional cereal bars were 15%. The quality characteristics of the nutritional cereal bar were also potential materials for good healthy food.

• Food Science and Preservation
• /
• v.13 no.2
• /
• pp.174-179
• /
• 2006

The objective of the study was to investigate the effect of steaming pressure (0.5, 1.0, and 1.5 bar), steaming time (5, 10, and 15 min), and storage period on Hardness, hardness rate constant and sensory characteristics of Baeksulgi prepared with optimum formula (rice new 100%, water 60%, salt 1.5%, and sugar 15%). Although the hardness was slowly increased during storage period from 0 hr to 8 hr and sharply increased after 12 hr of storage in case of 0.5 bay steam pressure, it was slowly increased after 12 hr storage time in case of steaming pressure at 1.0 ban Hardness rate constant of Baeksulgi was $0.217{\sim}0.184hr^{-1}$ at range of steaming time for $8{\sim}10$ min and pressure at $0.8{\sim}1.0$ bar which was relatively low. Hardness and elasticity of sensory evaluation were increased with the increases in steaming pressure, steaming time, and storage period but cohesiveness was decreased The highest overall preference was steaming pressure at 10 bar, steaming time for 10 min, and storage period for 12 hr. In conclusion, steaming pressure, steaming tim, and storage period influenced Baeksulgi quality such as hardness and sensory characteristics.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2010.05a
• /
• pp.26.2-26.2
• /
• 2010

최근에는 차세대 조명용 후보광원인 고출력 백색 LED를 개발하기 위한 경쟁이 치열하며, 이를 위해 업체가 고심하고 있는 가장 큰 문제 중의 하나가 칩에서 발생하는 열을 어떻게 관리하는가 하는 방열의 문제이다. 따라서, LED의 가장 큰 특징인 장수명을 손해보지 않기 위해서는 칩에서 발생되고 있는 열을 외부에 확산시키기 위한 기술 개발이 필수적이다. 다양한 방열소재 중 W-Cu 복합재는 W의 낮은 열팽창계수와 Cu의 높은 열전도도로 인해 방열소재로써 유망한 소재로 주목받고 있으나, 우수한 열적 특성을 발현하기 위해서는 고치밀화를 갖는 W-Cu 복합재 제조가 우선적으로 필요하다. W-Cu 복합체는 일반적으로 액상소결법을 통해 균일한 미세조직을 얻을 수 있으나, 열팽창계수를 낮추기 위해 Cu 함량이 적어지게 되면 치밀화가 어려우며 이를 해결하기 위해 나노입자를 갖는 분말을 이용하고자 하는 연구가 많이 진행되고 있다. 본 연구에서는 W과 Cu 산화물을 이용하는 것이 구성성분끼리의 편석이 발생하지 않으며, 소결성도 우수하여 양산화에 가장 접근한 방법으로 알려져 있다. 그러나, 지금까지의 얻어진 W-Cu 복합체의 경우, 분말상태에서의 얻어진 나노입자가 승온시에 마이크로 크기로 과도한 입자성장이 일어나기 때문에 소결 후에도 나노크기를 유지하기 어려울 뿐만 아니라, 구성상끼리의 응집체가 형성된다. 본 연구에서는 액상소결후에 W 입자가 Cu 기지내에 균일하게 분산되는 동시에 나노크기의 입자를 가지는 고분산 W-Cu 소결체를 얻고자 하였다. 이를 위해 금속산화물 분말의 분쇄를 위해 효과적인 방법으로 알려진 습식상태에서의 고에너지 볼밀링을 통하여 혼합된 텅스텐과 구리 산화물 분말의 수소환원공정을 통해 얻어진 100nm 이하의 입자를 가지는 W-20wt%Cu 나노복합분말을 출발분말로 사용하였다. W-20wt%Cu 나노복합분말의 성형체를 $1050^{\circ}C-1250^{\circ}C$의 온도범위에서 소결거동을 조사하였다. 그 결과, $1100^{\circ}C$ 온도에서 이론밀도에 가까운 소결밀도를 나타내었으며, 이는 기존에 비해 $100^{\circ}C$ 정도 치밀화 온도를 낮추는 결과이다. 소결체의 미세구조 관찰결과, 소결 후 약 200nm의 텅스텐 입자가 Cu내에 균일하게 분산되어 있었다. 제조된 W-Cu 시편에 대해서는 LED 응용성을 조사하기 위해 열전도도와 열팽창계수 등을 평가하였다.

• Journal of Korean Society of Environmental Engineers
• /
• v.36 no.2
• /
• pp.84-95
• /
• 2014

Recently, as a variety of techniques of CMF (Compressed media filter) that has advantages of high porosity and compressibility have been developed in the U.S. and Japan. Therefore, the interest of intensive wastewater treatment using CMF has grown. This study examined the feasibility of CMF with varying sewage water quality to determine the optimum operating conditions. A preliminary tracer test that investigated the filtering process under various compression and flow rate conditions was performed. In a high compression condition, different porosities were applied to each depth of the column. Therefore, a distinct difference between a theoretical value and results of tracer test was observed. For the TSS (Total suspended solid) removal and particle size distribution of CMF for pre-treatment water under the various compression conditions, the compression ratio of 30 percent as the optimal condition showed greater than 70% removal efficiency. In addition, the compression ratio of >15% was required to remove small-sized particles. Also, an additional process such as coagulation is necessary to increase the removal efficiency for < $10{\mu}m$ particles, since these small particles significantly influence the effluent concentration. Modeling results showed that as the compression rate was increased, TSS removal efficiency in accordance with each particle size in the initial filtration was noticeably observed. The modeling results according to the depth of column targeting $10{\mu}m$ particles having the largest percentage in particle size distribution showed that 150-300 mm in filter media layer was the most active with respect to the filtering.

• Journal of the Korean Vacuum Society
• /
• v.17 no.5
• /
• pp.466-472
• /
• 2008

Purple Gold is the alloy consisting of 78wt%Au-22wt%Al, and is expressed as a chemical formula, $AuAl_2$. Lately it is being used for the material of accessories or the decorative ornaments, being one of the colored golds having the peculiar purple color, like White Gold and Pink Gold. Purple Gold has the weak point in shaping through casting process due to the bad malleability and castability, being the intermetalic compound of Au and Al. Therefore, it is possible to produce the final product only by the cutting and the grinding process or to use it as a decorative coat with the thin film evaporation. This study implemented two kinds of thin film experiments. One is the case that heat treatment was made after Au and Al deposition evaporated separately with a weight ratio 78:22 on the 200nm$SiO_2$/Si substrate. The other is the case that the surface deposition was made through the vacuum evaporation, keeping the glass substrate temperature remain room temperature, using the bulk $AuAl_2$ as a source. The final film property was measured, focusing on the Purple Gold's color and thickness through the bare eye inspection, the microstructure analysis, the surface resistance analysis, the color difference analysis, and XRD analysis. Purple Gold was not formed, as the excessive surface agglomeration occurred, in case of being produced and treated thermally with 12.5nmAu/40nmAl/200nm$SiO_2$/Si structure. Our results suggest that of Purple Gold films, showing the same purple color as the bulk's, were successfully deposited with the direct thermal evaporation from the $AuAl_2$ bulk source.