• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.2
• /
• pp.154-161
• /
• 1995

In order to analysis of the stress distribution around flaws and the interaction effects between fatigue cracks, stress around micro hole was analyzed by Finite Element Method(F.E.M.) and micro hole specimens were tested using rotary bending fatigue machine and twisting fatigue machine to identify stress effects for fatigue cracks initiating from micro holes and interaction effects between micro holes. The results are as follows : Interaction effects of .sigma. $_{y}$for the micro hole side is larger than the large micro hole side when the interval between micro holes is near. Stress concentration factor increase as the diameter of micro hole becomes smaller. But, stress field of micro hole is smaller than that of large micro hole at h .leq. r (h:depth of micro hole, r:radius of micro hole) and that of large hole is larger than that of small micro hole at h >r expect the small range from micro hole.e.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2009.05a
• /
• pp.796-800
• /
• 2009

토목구조물 및 사면의 붕괴는 집중호우가 내리는 경우 많이 발생하고 있으며, 특히 사면에서는 붕괴까지의 변형이 급속히 진행되어 이를 사전에 예방하기는 매우 어려운 현실이다. 침투 및 배수과정에서의 사면 붕괴는 강우침투로 인한 지반의 물리적 특성변화가 직접적으로 사면의 안전계수 변화에 영향을 주는 것으로 판단되며, 이때 발생하는 물리적 특성변화로는 침투시 사면 내 지반의 단위 중량은 증가하여 전단응력의 증가 및 전단강도 감소현상이 발생하며, 이와 반대로 사면 내 배수로 인하여 전단응력의 감소 및 전단강도의 증가현상이 발생한다. 따라서 본 연구에서는 강우침투로 발생하는 지반의 포화도 변화를 지반 내 투수계수의 함수로 설명하여 강우로 인한 지반의 침투 및 배수과정을 규명하고자 한다. 일반적으로 지반 내 지하수의 침투과정은 라플라스 공식을 적용한다. 그러나 라플라스 공식은 정상 상태(Steady State)일 경우에만 사용할 수 있고, 강우 등으로 인한 지하수의 수두 변화가 발생한 비정상 상태(Unsteady State)의 경우에는 부적합하므로 사면과 옹벽 등의 토질구조물에서는 안전성 변화를 계산할 수 없다. 이를 위해 사면 내 지반의 침투 및 배수과정을 투수계수의 함수로 나타내어, 강우의 침투과정을 Fourier Series, 변수분리법 및 섭동함수를 사용하여 식으로 유도함으로서 강우에 의한 지반의 침투 및 배수과정에 따른 사면 내 지하수의 분포를 예측한다. 침투과정 해석을 위하여 지표에서 포화대까지의 깊이 10m의 모델사면 및 지표부터 포화대까지의 포화도는 직선으로 비례한다는 가정을 적용한다. 먼저 푸리에 급수를 이용, 시간에 따른 온도를 열전달에 관하여 편미분하여 발생하는 열확산계수를 투수계수로 변환함에 따라 지하수의 시간과 수직방향거리에 대한 지반의 포화도를 산정한다. 변수분리법은 산정된 포화도에 지반의 초기조건과 경계조건를 고려하기 위해 적용하며, 변수분리법에 의해 산정된 지하수 분포를 섭동함수법으로 과도 및 정상상태로 분류한다. 본 연구의 수행으로 인해 얻어진 결과를 요약하면 다음과 같다. 첫째, Fourier Series와 변수분리법, 섭동함수를 이용하여 강우에 의한 지반의 포화도 변화를 수식적으로 나타낼 수 있으며 둘째, 지반에서의 강우침투과정을 식으로 표현함으로서, 깊이별 시간에 따른 포화도의 영역이 상부로부터 하부로 전이되는 과정을 알 수 있다. 셋째, 푸리에 급수를 이용한 지반의 침투계산으로 강우로 인한 지반의 포화영역 및 불포화영역을 명확히 구분할 수 있으며, 각 깊이별 포화도를 계산하여 각 구간에서 불포화구간의 전단강도에 대한 보다 정확한 계산이 가능하리라 판단된다.

• Journal of Industrial Technology
• /
• v.20 no.A
• /
• pp.169-178
• /
• 2000

The 4-point bending tests have been performed In order to estimate the effect of TIG-dressing on fatigue strength and fatigue characteristics quantitatively for non load-carrying fillet welded joints subjected to pure bending. As a result of fatigue tests, fatigue strengths of as-welded specimens have satisfied the grade of fatigue strength prescribed in specifications of korea, AASHTO and JSSC. Fatigue strength at 2 million cycles of TIG-dressing specimens have increased compared with as-welded specimens. As the result of beachmark tests, fatigue cracks occurred at several points, where the radius of curvature and flank angle in the weld bead toes were low, and grew as semi-elliptical cracks, then approached to fracture. As a result of finite element analysis, stress concentration factor in weld bead toes has closely related to the flank angle and radius of curvature, and between these, the radius of curvature has more largely affected in stress concentration factor than flank angle. As a result of fracture mechanics approaches, the crack correction factor of test specimens has largely affected on stress gradient correction factor in case a/t is below 0.4. From the relations between stress intensity factor range estimated from FEM analysis and fatigue crack growth rate, fatigue life has been correctly calculated.

• Proceedings of the KSME Conference
• /
• 2001.06a
• /
• pp.217-222
• /
• 2001

For the life evaluating of notched members, it is the best way that performing the real fatigue test of structure containing notch. But this method required generally much times and costs to evaluate fatigue life. So, generally we use the modified S-N curve or several methods to predict fatigue life. In this study, crack initiation life was evaluated by fatigue testing the SAE keyhole specimen and smooth specimen made of Al 7075-T6 alloys using the constant load then obtained S-N curve of smooth specimen and P-N curve of SAE keyhole specimen. And, fatigue lives of keyhole specimen are predicted using some life prediction methods (Nominal range I method, Nominal range II method, FEM analysis) for investigating experimented results, and that were compared with experimental data. Predicted fatigue lives by FEM analysis were corresponded with experimental data between 1/3times and 3times on the whole, and predicted fatigue lives using modified S-N curve (Nominal range I method, Nominal range II method) were nonconservative compared with that of FEM analysis.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.7-12
• /
• 2004

Large-sized pins are usually used to lift and handle large low speed diesel engine crankshaft. There has then been a need to reduce and optimize the weight of the traditionally used pins. Making an hole by cutting the inside of the pin out was investigated in view of static and fracture strength. To compensate the stress increase caused by the introduction of the inner hole, the groove in the circumferential direction pre-existing on the pin is to be removed. Finite element analysis was carried out for both the original model and weight reduced model. Stress intensity factors for semi-elliptical defects assumed on the pin for the original model and weight reduced model was calculated using the ASME method and compared with the fracture toughness test result of the pin material. The diameter of the cutting hole for the revised model was determined based on the analysis results.

• Journal of Ocean Engineering and Technology
• /
• v.30 no.4
• /
• pp.260-267
• /
• 2016

Considering the effect of dynamic response amplification, a reliability analysis of an offshore wind turbine support structure under an earthquake is presented. A reliability analysis based on the dynamic response requires a large amount of time when using not only a level 3 approach but also level 2 such as a first order reliability method (FORM). Moreover, if a limit state is defined by using the maximum stress at a structural joint where stress concentration occurs, a three-dimensional element should be used in the finite element analysis. This makes the computational load much heavier. To deal with this kind of problem, two techniques are suggested in this paper. One is the application of a quasi-static structural analysis that takes the dynamic amplification effect into account. The other is the use of a stress concentration factor to estimate the maximum local stress. The proposed reliability analysis is performed using a level 2 FORM and verified using a level 3 simulation approach.

• Journal of Korean Society of Steel Construction
• /
• v.10 no.3 s.36
• /
• pp.497-508
• /
• 1998

The objective of this study is to examine fatigue behavior of as-welded butt-welded joints with incomplete penetration from fatigue tests. The test results are the following. In static tests, tensile strength and yield strength of butt-welded joints are constant regardless of incomplete penetration. And in fatigue tests, fatigue strength of fully penetrated butt-welded joints satisfies fatigue limits, prescribed in Korean Specifications and JSSC, respectively. The results show that as the magnitude of incomplete penetration increases, fatigue strength decreases. In fractured surfaces, full and incomplete penetration specimen show different shapes, it is because that stress concentration factor vary with structural geometry in bead toe and root tip, and certify in FEM analysis. This study suggests that defects such as incomplete penetration from welding must be avoided in order to attain the sufficient life of steel structures.

• Tunnel and Underground Space
• /
• v.20 no.1
• /
• pp.65-72
• /
• 2010

Crack-controlled blasting method which utilizes notched charge hole has been proposed in order to achieve smooth fracture plane and minimize the excavation damage zone. In this study, the blast models, which have a notched charge hole, were analyzed using dynamic fracture process analysis software to investigate the effect of the geometry of a notched charge hole and decoupling indexes of the charge hole on crack growth control in blasting. As a result, crack extension increased and damage crack decreased with the notch length. Ultimately, stress increment factors and resultant fracture patterns with different notch length and width were analyzed in order to examine the effect factors on the crack growth controlling in rock blasts using a notched charge hole.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.6
• /
• pp.589-596
• /
• 2015

The occurrence of an inclined edge crack in transversely piezoelectric material is analyzed. Concentrated antiplane mechanical and inplane electrical loads are applied at the boundary and crack surface, respectively. The crack surfaces are assumed to be impermeable to the electric field. Using the Mellin transform with the introduction of a generalized displacement vector, the problem is formulated, and the Wiener-Hopf equation is derived. By solving the equation, the solution is obtained in a closed form. The intensity factors of the stress, the electric displacement, and the energy release rate are obtained for any crack length and inclination angle. These solutions can be used as fundamental solutions and can be superimposed to represent any arbitrary electromechanical loading.

• Journal of the Society of Naval Architects of Korea
• /
• v.28 no.2
• /
• pp.285-292
• /
• 1991

In this paper, typical tubular joints' fatigue strength is investigated focussing un the Stress Concentration Factors calculation using Finite Element Methods. For the calculation of the SCF of the members, the joints are modeled using thin shell elements and comprehensive analysis are carried out. Related techniques for the numerical analysis are studied. Experimental studies are performed for the verification and comparison with the numerical analysis results. Model tests of K joints are carried out not only for finding SCF values but also for the calculation of fatigue lives of the joints using specially designed test facilities.