• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 춘계학술대회논문집
• /
• pp.1189-1194
• /
• 2002

Acoustic intensity is usually estimated by the cross-spectrum of acoustic pressure at two adjacent micrphones. The cross-spectrum calculated by digital Fourier transform technique will unavoidally have leakage error since the period of signal will not be usually coincident with record length. Therefore, the acoustic intensity estimated by the conventional r]n analyzer will show distorted value. In this paper the expression of the Fourier transformed data of a harmonic signal is formulated when there is leakage error. The method to elimate the effect of leakage error from the contaminated data is also proposed. Some numerical examples show the validation of the proposed method.

• 한국자동차공학회논문집
• /
• 제5권3호
• /
• pp.171-171
• /
• 1997

Sound intensity distributions and energy flow in the near field of dipole source system and flat plate were investigated. First, the effectiveness of complex acoustic intensity was proved by using mathmatical and experimental methods in order to indentify noise sources and transmission paths of dipole field which is effected by the presence of neighbouring coherent sources. Next, analytical complex acoustic intensity method was discussed and the characteristics and energy flow of sound induced from the plate are clarified. The velocity of plate obtained from Finite Element Method was used for calculation of complex acoustic intensity in the near field. Finally experimental complex acoustic intensity method was applied to a passenger car. It can be seen that complex acoustic intensity method using both of active and reactive intensity is vital in devising a strategy for the identification and the reduction of vibration and noise.

• 한국자동차공학회논문집
• /
• 제5권3호
• /
• pp.159-171
• /
• 1997

Sound intensity distributions and energy flow in the near field of dipole source system and flat plate were investigated. First, the effectiveness of complex acoustic intensity was proved by using mathmatical and experimental methods in order to inden- tify noise sources and transmission paths of dipole field which is effected by the presence of neighbouring coherent sources. Next, analytical complex acoustic intensity method was discussed and the characteristics and energy flow of sound induced from the plate are clarified. The velocity of plate obtained from Finite Element Method was used for calculation of complex acoustic intensity in the near field. Finally experimental complex acoustic intensity method using both of active and reactive intensity is vital in devising a strategy for the identification and the reduction of vibration and noise.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집B
• /
• pp.204-209
• /
• 2001

The more sophisticated patterns of propagation model is presented in this paper, which includes three different source characteristics (spherical, cosine and dipole). The spherical, cosine and dipole radiation characteristics compared, and sound event level and the maximum sound level are calculated by experiment and calculation. It is shown that patterns of propagation have dipole characteristics for low speed range (below about 150Km/h) at electric multiple system. We know that push-pull high speed system has cosine characteristics of noise propagation at low speed range (below about 200Km/h).

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1999년도 춘계학술대회 논문집
• /
• pp.222-228
• /
• 1999

The two-microphone sound-intensity technique has been used for the detection of defects in radially loaded ball bearings. The difference in the sound-intensity levels measured for bearings with no defect and for those with intentionally introduced defects of different sizes in their elements under various operating conditions of loads and speeds is demonstrated. A change in the intensity frequency spectrum because of the defects is observed. The results show that the detectability of an outer-race defect is much better than that of on inner-race or ball defect. It is difficult to detect defects at lower speeds. Sound-pressure measurements were also performed fur comparison, and it is shown that the detectability of defects by sound-intensity measurements is better than that by sound-pressure measurements.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 추계학술대회논문집 II
• /
• pp.1132-1137
• /
• 2001

The smart foam that is first proposed by Fuller(2) is not applicable to active noise control in a duct having flow. Thus. this paper presents the ring-type smart foam as an alternative. The ring-type smart foam consists of polyurethane acoustic foam of lining shape and PVDF film embedded along the mid-surface of the foam lining. A feedforward adaptive filtered-x LMS controller is used to minimize the signal from the error microphone. To enlarge quiet sound region. two error microphones are used to update system modeling filter (SIMO method). Sound intensity control using the ring-type smart foam is also discussed

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 추계학술대회논문집 II
• /
• pp.1156-1161
• /
• 2001

Acoustic intensity is usually estimated by the cross-spectrum of acoustic pressure at two adjacent microphones. The cross-spectrum calculated by digital Fourier transform technique will unavoidally have leakage error since the period of signal will not be usually coincident with record length. Therefore, the acoustic intensity estimated by the conventional FFT analyzer will show distorted value. In this paper, the expression of the Fourier transformed date of a harmonic signal with a single frequency is formated when there is leakage error. The method to elimate the effect of leakage error from the contaminated data is also proposed. Some numerical examples show the validation of the proposed method.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 추계학술대회논문집
• /
• pp.629-632
• /
• 2005

What does sound look like if we can see it? It might depend on the acoustic variables we want to see. In this article, we propose various ways to visualize or express sound field in much more intuitive manner. In particular, new visualization schemes that can effectively visualize sound intensity and 3D pressure field are proposed. This allows us to represent sound pressure, particle velocity and acoustic conductance at the same time, even in three-dimensional coordinate. Visualization examples corresponding to the proposed techniques show that we can successfully transfer the meaning of physical variable to visual space.

• 한국철도학회논문집
• /
• 제19권1호
• /
• pp.1-10
• /
• 2016

본 논문은 고속열차 객실 내 유리창의 차음 성능을 향상시키기 위한 기반연구로, 접합유리에 사용되는 고분자 필름의 물성과 음향학적 특성을 분석하여 그 상관관계를 살펴보고자 하였다. 기존에 사용되고 있는 PVB(polyvinyl butyal) 필름 및 다른 단량체 비율을 가지는 PVB 유도체, 그리고 유리 사이 차음재로 사용가능 한 PC(polycarbonate)의 동적기계적 특성을 분석(DMA)하였다. DMA 분석을 통해 상온에 가까운 온도범위에서 유리전이온도($T_g$)를 가지며 tan ${\delta}$(loss tangent) 값이 큰 것으로 나타난 PVB-HEMU 시편의 댐핑(damping) 성능이 가장 우수할 것으로 예측하고, 이를 고속철도 차량의 접합유리창과 동일한 구조에서의 투과손실 시험과 해석을 통해 검증하고자 하였다. 접합필름의 종류에 따른 유리창 투과손실 값을 투과손실 측정(인텐시티법)과 FE 해석을 이용해 도출하고, 고분자 필름의 물성과 음향성능 간 상관관계 분석을 위한 기초자료를 구축하였다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2003년도 제21회 추계학술대회 논문집
• /
• pp.271-277
• /
• 2003

최근 환경 소음이 사회적인 문제로 대두되고 있는 가운데, 생활수준의 향상으로 저소음화에 대한 요구가 증가되고 있는 실정이다. 이와 같이 소음에 관한 일반인들의 관심이 높아지면서 생환주변에서 주요 소음원으로 지적되고 있는 회전기계, 특히 가전제품을 비롯한 유동관련 기계류의 소음을 낮추기 위한 노력이 절실히 요구되고 있다. 본 소평팬에 대한 연구에서는 음압 및 음향인텐시티를 이용하여 소음원을 해석하였다. 이때, 광센서를 이용한 축류형 팬의 동기화가 수행되어졌고, 팬 형상에서 정확한 소음원의 위치를 규명하기 위한 기록시간의 결정이 제안되어졌다. 소음 발생하는 위치를 규명하였고, 지향성 연구를 통하여 축류형 팬의 방사형태를 결정하였으며, 음의 흐름도를 가시화 하였다.