• Composites Research
• /
• v.16 no.6
• /
• pp.16-22
• /
• 2003

This paper studied the AE(acoustic emission) characteristics of the laminated composite structures. The composite stiffened panels under the compressive loading emitted various AE signals when they buckled or changed the buckling modes. In addition, the failure initiated and propagation generated a lot of complex signals. From the continuous signal generation. we identified when the failures initiated and whether they propagated or not. The single lap joint of laminated plates under tensional load also generated AE signals when bonding region failed. The first failure occurrence and its propagation are monitored by generated AE signals. The characteristics of AE signals used in this analysis are cumulative hits, hit distribution, peak frequency of generated AE waveform and amplitude of signals. The analysis of AE signals shows that continuous increment of cumulative hits can be regarded as damage propagation and three dominant peak frequencies can correspond to typical failure modes in the laminated composites.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.33 no.2
• /
• pp.198-204
• /
• 2013

Acoustic emission(AE) signal was detected during charge and discharge of lithium ion battery to investigate relationships among cumulative count, discharge capacity, and microdamages. AE signal was received during accelerated charge/discharge cycle test of a coin-type commercial battery. A number of AE signals were successfully detected during charge and discharge, respectively. With increasing number of cycle, discharge capacity was decreased and AE cumulative count was observed to increase. Microstructural observation of the decomposed battery after cycle test revealed mechanical damages such as interface delamination and microcracking of the electrodes. These damages were attributed to sources of the detected AE signals. Based on a linear correlation between discharge capacity and cumulative count, feasibility of AE technique for evaluation of battery degradation was suggested.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.23 no.5
• /
• pp.480-487
• /
• 2003

To improve environmental control in various plants, signal characteristics of plants have been studied by a nondestructive technique. In this paper, the acoustic emission (AE) from plants was analyzed for water stress dependency. AE signals were taken from gymnosperm and angiosperm. AE sensor detected AE signals from the plant stem underneath the plant surface below the sensor. AE hit-event counts in daytime were more than those in night time, and it was found that the daily hit counts pattern was strongly affected by the water stress in the plant. frequency bands of AE signals from the angiosperm was different from those from the gymnosperm. Frequency bands of AE in outdoor condition were in accord with those in indoor having similar conditions.

• Journal of the Korea Convergence Society
• /
• v.11 no.11
• /
• pp.249-255
• /
• 2020

This study developed the health monitoring method of press process using the acoustic emission (AE) sensor and high-pass filter. Also, the AE parameters such as ring-down count and peak amplitude are used. Based on this AE signal, the AE parameters were acquired and was utilized to detect the crack of the specimen. Since the defect detection is difficult due to noise and low magnitude of signal, the signal noise and press operation frequency were checked through the Short Time Fourier Transform(STFT) and damped. High-pass Filtering data was applied to AE parameters to select effective parameters. By using this signal processing techniques, the proposed AE parameters could improve the performance of defect detection in the press process.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.8
• /
• pp.863-867
• /
• 2014

In this study, an acoustic emission (AE) sensor was used for measuring the abrasive and molecular-scale phenomena in chemical mechanical polishing (CMP). An AE sensor is a transducer that converts a mechanical wave into an electrical signal, and is capable of acquiring high-level frequencies from materials. Therefore, an AE sensor was installed in the CMP equipment and the signals were measured simultaneously during the polishing process. In this study, an AE monitoring system was developed for investigating the sensitivity of the AE signal to (a) the variations in the material properties of the pad, slurry, and wafer and (b) the change in conditions during the CMP process. This system was adapted to Oxide and Cu CMP processes. AE signal parameters including AE raw frequency, FFT, and amplitude were analyzed for understanding the abrasive and molecular-level phenomena in the CMP process. Finally, we verified that AE sensors with different bandwidths could function in complementary ways during CMP process monitoring.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.50.2-50.2
• /
• 2011

자동차용 CNG 연료탱크의 복합재료 중앙부 표면에 150 kHz 공진형 음향방출센서를 부착하고, 물을 매질로 하여 용기의 내압을 단계적으로 상승시켜 가면서 각 단계에서 일정시간 압력을 유지시키고 그 때 발생하는 음향방출신호를 획득하였다. 이 때 획득한 음향방출신호의 amplitude, count, duration 및 risetime 등과 같은 음향방출 변수들의 분포를 살펴본 결과 복합재료 압력용기의 손상메커니즘을 추정하고 손상정도를 평가하는데 유용하였다.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.31 no.5
• /
• pp.529-535
• /
• 2011

In this study, evaluation of acoustic emission signals characteristics for the post weld heat treated (PWHT) multi-pass weldment and weldment was dealt. Charpy standard specimens were taken from the lowest, middle and highest regions of the weld block. Pre-crack was made using the repeated load. Four point bend and AE tests were conducted simultaneously. Regardless of the specimens, AE signals were absent within elastic region and produced in the process of plastic deformation. AE signals for all specimens were not emitted after the maximum load. Value of signal strength for the all PWHT specimens was lower than that of the weldment. Besides, relations of plastic deformation zone size and accumulated AE counts for the PWHT specimens were more simple compared with the weldment. In case of the PWHT specimen, particles on the fractured surface decreased prominently compared with the weldment due.to PWHT. From these results, it can be concluded that PWHT was effective in reducing the AE sources for the weldment.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.33 no.5
• /
• pp.430-435
• /
• 2013

This study is investigation of the characteristics for acoustic emission signal generated by destruction on glass fiber bundles and specimen that was machined composite materials surrounding the outside of GFRP cylinder. The Amplitude of acoustic emission signal gets bigger as the cutting angle of knife increases. Accordingly, the number of hits in destruction of composite materials specimen have more in longitudinal direction (longitudinal direction to the glass fiber) than in hoop direction (horizontal direction to the glass fiber) while the amplitude of signals were bigger in hoop direction than longitudinal direction. It was found out that the amplitude of the glass fiber breakage is more than 40 dB and that the amplitude of signal for matrix crack was less than 40 dB because matrix crack signal was not observed when threshold value is 40 dB and matrix crack signal suddenly appered when threshold value is 32 dB. The slope of the amplitude is related to the acoustic emission source and the slope of the amplitude of the horizontal and vertical directions are 0.16 and 0.08. In particular, The slope of the amplitude of longitudinal direction breakage appear similar to the glass fiber breakage and therefore Acoustic emission source of longitudinal direction breakage is estimated the glass fiber breakage.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.21 no.3
• /
• pp.251-260
• /
• 2001

Damage Profess of CFRP laminates under monotonic tensile test was characterized by the correlation between Acoustic Emission(AE) and Ultrasonic Test(UT). The amplitude distribution of AE signal from a specimens is an aid to the determination of the extent of the different fracture mechanism such as matrix crack, debonding, fiber pullout and fiber fracture as load is increased. In addtion, the characteristics of ultrasonic amplitude attenuation are useful lot analysis of the different type of fracture mechanism. Different orientation of carbon fiber reinforced plastic specimens were used to investigate the AE amplitude range and ultrasonic amplitude attenuation. Finally, loading-unloading tests were carried out to check Felicity effect. During the tests, ultrasonic amplitude attenuation was investigated at the same time and compared with AE parameters. The result showed that two parameters of both AE and UT could be effectively used for analysis of fracture mechanism in CFRP laminates.

• Journal of Power System Engineering
• /
• v.6 no.2
• /
• pp.60-67
• /
• 2002

연삭가공은 나노스케일(Nano-scale)의 미소한 입자 절삭날을 이용한 가공으로, 공작물의 표면을 경면(Mirror surface)으로 가공할 수 있어 제품의 최종 마무리공정으로 사용되어 왔다. 그러나 연삭공정에 있어서는 공구(연삭숫돌)의 수명이 다하거나 가공계(Machining system)가 불안정해지면 채터진동과 연삭버닝 등의 현상이 발생하여 가공물의 표면품위를 저하시키는 요인으로 작용하고 있다. 따라서 본 연구는 원통플른지 연삭공정을 대상으로 공작물에서 발생하는 음향방출 신호와 연삭기 주축 모터의 동력 신호를 연삭가공 중에 검출하고, 이를 신경회로망에 적용하여 연삭가공 상태를 진단하는 시스템을 구축하고, 그 성능을 평가하였다.