• Journal of the Korean Society for Marine Environment & Energy
• /
• v.6 no.4
• /
• pp.52-66
• /
• 2003

Generally we have difficulty in removing oil using mechanical devices because recovery rate and recovery efficiency decrease remarkably when operating in thin oil films or in oils of very high viscosity In the Present study a series of experiments were carried out to study the effect of operating conditions on the rate of recovery for the spilled oil using a drum type skimmer. For each set of experiments depth of immersion, oil film thickness and the circumferential speeds were varied systematically to find the effects on the recovery rate. The results shows that recovery rate is dependent on the contact angle for the depth of immersion and the highest rate of oil recovery shows in the case of a contact angle of 45°(h/d=0.15). For the removal of spilled oil the optimal circumferential speed can be found as the critical value to reach the saturated recovery rate for a given oil film thickness and depth of immersion. Even in thin oil thickness we have enough recovery rate and recovery efficiency within critical circumferential speed this way.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.1 no.1
• /
• pp.66-82
• /
• 1998

The hydrodynamic characteristics of oil skimmers are reviewed. The paper consists of (1) introduction of the general aspects of oil skimmers, including kinds, performance indices, current market situations, (2) the analysis of factors affecting oil- skimming, (3) the review of existing papers with a special focus on hydrodynamic problem and finally (4) conclusions and some suggestions. The purpose of this paper is to draw hydrodynamists' attentions on oil skimmer, more broadly on marine oil spill.

• Journal of Ocean Engineering and Technology
• /
• v.11 no.3
• /
• pp.124-131
• /
• 1997

흡착식 유회수기의 운전조건을 결정하는데 있어서 스키머의 구동속도와 기름의 물리.화학적 성질에 따른 스키머의 유회수율을 예측하는 것이 필요하다. 이 문제에 대한 이론적인 접근으로 수직구동 평판상에 부착된 기름층의 자유표면유동을 두가지 방법으로 조사하였다. 그 하나는 표면코팅시 얇은 유막에 대하여 수행하는 정상유동해석이며, 다른 방법으로는 스키머 표면유막에 대한 안정성해석이다. 해석은 기름층이 충분히 두꺼워서 스키머는 기름층에서만 작동한다고 가정하였다. 이론추정 결과는 롤러타입의 스키머에 대하여 계측한 실험치와 비교하였는데, 유막의 안정성해석 결과가 유회수기와 같이 상대적으로 고레이놀즈수에서 작동하는 유동의 경우에는 정상해석보다 좀 더 합리적으로 유막의 두께를 산정함을 알 수 있었다. 한편, 물위에 떠있는 얇은 유막층의 유회수성능도 실험하여서 주어진 유막두께에 대하여 롤러의 최적구동속도를 함께 조사하였다.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.11 no.2 s.23
• /
• pp.103-108
• /
• 2005

For the development of a disk type oil skimmer for a tank lorry, a basic study on comparison of oil recovery performance between disk materials of oil skimmer was conducted. The experiment results are summarized as follows: In all the disks, the volume of recovery of bunker-A oil was greater than diesel oil. In light oil, there was nearly no differences in the volume of oil recovery by disk material, but in the case of bunker A oil, recovery efficiency showed big differences depending on the disk materials. For diesel oil, the differences in the volume of oil recovery per unit of operation time from the initial time zone were hardly shown. However, the volume of recovery of bunker-A oil linearly increased from the initial operation time in all the disks and the increase showed a slew moving trend as time. went on; therefore, the volume of oil recovery per unit of operation time showed differences depending on time. This result shows that oil viscosity has an effect on the disk recovery efficiency. When comparing the mass of pure oil recovery and the volume of water recovery in the total mass of recovery by bunker-A oil, there was no difference in the volume of oil recovery between the window-aluminum material disk and the disks consisting of other materials, but the volume of water recovery of the former was relatively very small This shows the most ideal result in view of oil recovery efficiency that considers the volume of water recovery. In conclusion, it was found that aluminum is the most advantageous as the material for tank lorry oil skimmer disk.

• Proceedings of KOSOMES biannual meeting
• /
• 2005.11a
• /
• pp.165-170
• /
• 2005

A basic study for the development of a disk type oil skimmer for a tank lorry, compares via experiments to the oil recovery differences by material between the existing oil skimmer disk and several discs which oil adhesion are possible. The experiment results in this study are summarized as follows: In all the disks, the mass of recovery of bunker-A oil was greater than light oil. In light oil, there was nearly no differences in the mass of oil recovery by disk material, but in the case of bunker A oil, recovery efficiency showed big differences depending on the disk materials. For light oil, the differences in the mass of oil recovery per unit of operation time from the initial time zone were hardly shown. However, the mass of recovery of bunker-A oil linearly increased from the initial operation time in all the disks and the increase shaped a slow moving trend as time went on; therefore, the mass of oil recovery per unit of operation time showed differences depending on time. This result shows that oil viscosity has an effect on the disk recovery efficiency. When comparing the mass of pure oil recovery and the mass of water recovery in the total mass of recovery by bunker-A oil, there was no difference in the mass of oil recovery between the window-aluminum material disk and the disks consisting of other materials, but the mass of water recovery of the former was relatively very small. This shows the most ideal result in view of oil recovery efficiency that considers the mass of water recovery. In conclusion, it was found that aluminum is the most advantageous as the material for tank lorry oil skimmer disk.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.5
• /
• pp.457-464
• /
• 2010

Representative methods for removing spilled oil include mechanical skimming, chemical treatment, burning at the surface of the spilled oil, and microbiological degradation. Among these methods, mechanical skimmer is the most efficient. Mechanical skimming can be classified into the following categories: belt-type, disk-type, weir-type, drum-type. We designed models with a submerged orifice for use in our experiments, for an objective and systematic evaluation of the recovery efficiency of mechanical skimming. Basically, oil is lighter than seawater and hence tends to float on the surface of the latter if there is sufficient time for floating. The present skimmer is kind of wear-type with the submerged orifice for seawater to be squeezed through, minimizing water content in the tank. From the experimental results, we identify the parameters that influence the oil recovery rate and recovery efficiency. The recovery efficiency can be enhanced by increasing the thickness of the oil layer in the first oil accumulative tank.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.2 no.1
• /
• pp.34-39
• /
• 1999

Removal of spilled oil over the sea and the river has become one of the urgent problems in these days. Removing oil using mechanical devices by adhesion method is known to be closely related with the problem of estimating the thickness of film remaining on the surface of solid withdrawn from a quiescent liquid. In the present study a series of experimental results are compared with the analytic estimation for the thickness of film remaining on the solid surface using non-dimensional analysis. For the case of pure water both results show the remarkable agreement. However, discrepancy has been found for the case of Bunker C oil and diesel oil. The analytic estimation over-predicts the experimental value for the case of Bunker C oil and under-predicts it for the case of diesel oil. Further study is required to investigate the real situation including a contact angle and the property difference between oil and water.

• Proceedings of KOSOMES biannual meeting
• /
• 2017.04a
• /
• pp.225-225
• /
• 2017

• 건강소식
• /
• v.23 no.10 s.251
• /
• pp.20-21
• /
• 1999

• 건강소식
• /
• v.23 no.12 s.253
• /
• pp.20-21
• /
• 1999