• The KSFM Journal of Fluid Machinery
• /
• v.15 no.4
• /
• pp.27-32
• /
• 2012

Gas turbines for an aircraft have the start and restart capabilities within their flight envelop. It is an important item for engine qualification and substantiated with the test. Experimental investigations were carried out to find the relation between the corrected torque and the corrected rotating speed of an air turbine starter in this study. A dedicated air supply system for the air turbine starter and a special device to measure the torque and the rotating speed of the air turbine starter were developed and installed at the altitude engine test facility in Korea Aerospace Research Institute. Experimental results show that the relations between the corrected torque and the corrected rotating speed of the air turbine starter are linear and the inlet temperature and pressure conditions for the air turbine starter were found out to provide minimum required torque for the engine qualification test at various altitude. The start and restart tests for the currently developing engine were successfully performed using this experimental results.

• The KSFM Journal of Fluid Machinery
• /
• v.9 no.2 s.35
• /
• pp.7-12
• /
• 2006

This study is to develop a system of electric power generation utilizing the wind resources available in the domestic wind environment. We tested drag-type vortical wind turbine models, which have two different types of blades: a flat plate and circular arc shape. Through a performance test, conditions of maximum rotational speed were found by measuring the rpm of wind turbine. The rotational speed was measured by a tachometer in a wind tunnel and the tunnel wind speed was by using a pilot-static tube and a micro manometer. The performance test for a prototype was accomplished by calculating power, power coefficient, torque coefficient from the measurement of torque and rpm by a dynamometer controller From the measurements for miniature turbine models with two different blades, the circular arc shape was found to Produce a maximum rotational speed for the same wind velocity condition. Based on this result, the prototype with the circular arc blade was made and tested. We found that it produces 500W at the wind velocity of 10.8 m/s and the power coefficient was 20%.

• The KSFM Journal of Fluid Machinery
• /
• v.14 no.1
• /
• pp.42-47
• /
• 2011

Measurement uncertainty analysis of fuel flow using turbine flowmeter was performed for the case of altitude engine test. SAE ARP4990 was used as the fuel flow calculation procedure, as well as the mathematical model for the measurement uncertainty assessment. The assessment was performed using Sensitivity Coefficient Method. 11 parameters involved in the calculation of the flow rate were considered. For the given equipment setup, the measurement uncertainty of fuel flow was assessed in the range of 1.19~1.86 % for high flow rate case, and 1.47~3.31 % for low flow rate case. Fluctuation in frequency signal from the flowmeter had the largest influence on the fuel flow measurement uncertainty for most cases. Fuel temperature measurement had the largest for the case of low temperature and low flow rate. Calibration of K-factor and the interpolation of the calibration data also had large influence, especially for the case of very low temperature. Reference temperature, at which the reference viscosity of the sample fuel was measured, had relatively small contribution, but it became larger when the operating fuel temperature was far from reference temperature. Measurement of reference density had small contribution on the flow rate uncertainty. Fuel pressure and atmospheric pressure measurement had virtually no contribution on the flow rate uncertainty.

• The KSFM Journal of Fluid Machinery
• /
• v.10 no.3 s.42
• /
• pp.17-24
• /
• 2007

This paper presents the design procedure of a vertical wind turbine named jet-wheel-turbo turbine and the numerical and experimental verifications. The design parameters such as the rotor inlet angle, the diameter-to-hub ratio, the inlet guide outlet angle and the solidity were optimized to maximize the energy transfer, and to further increase the turbine efficiency by applying the side guide vane and the side opening to the rotor. The maximum power coefficient of 0.59, which is much higher than the ever-designed three-bladed horizontal turbines, was experimentally obtained when the optimal inlet- and side-guide vanes were installed and both sides of the rotor were 80% opened. The maximum power coefficients occur at the tip speed ratio ranging between 0.6 and 0.7. This vertical-axis turbine model can be applied to the large-scale power generation system with the speed and torque control algorithm for the specified wind characteristics.

• 한국전산유체공학회:학술대회논문집
• /
• 1995.10a
• /
• pp.225-234
• /
• 1995

터빈익렬내부의 유동해석을 위해 비압축성 점성유동해석을 이용한 수치 해석 프로그램을 개발하였다. 지배방정식으로는 2차원의 비정상 비압축성 Navier-Stokes 방정식을 일반화된 곡선좌표계로 전환하여 암시적으로(implicitly) 반복적인 시간진행방법을 이용하여 유동해석을 하였다. 지배방정식의 각항들은 시간에 대해 1차의 정확도 그리고 영역에 대해서는 2차의 정확도, 대류항에 대해서는 3차의 정확도를 가지는 Upwind기법을 적용하였다. 특히, 실험적 접근이 매우 어려운 터빈의 정익과 회전하고 있는 동익과의 상호운동을 멀티블럭기법과 데이터 interface를 통해 보다 쉽게 해석할 수 있었다. 본 연구결과는 정익만을 계산한 타 연구자의 결과와의 비교시 매우 일치하였으며 물리적인 유동을 잘 파악할 수 있었다. 난류유동 해석을 위해서 Baldwin-Lomax 모델을 적용하였다.

• The KSFM Journal of Fluid Machinery
• /
• v.7 no.6 s.27
• /
• pp.28-37
• /
• 2004

An experimental study is conducted to investigate flow characteristics on a small axial-type turbine which is applied as the rotating part of air tools. It operates in a partial admission due to consumption restriction of the high pressure air. In this operating condition, it is necessary to understand flow characteristics for obtaining the high specific output power. Tested turbine consists of two stages and the mean radius of flow passage is less than 10mm. A 6 bar pressure air is used to operate the turbine. The experimental results show that flow angles depend on the measuring location along the circumferential direction, but its discrepancy is alleviated along the axial direction. Absolute flow velocities show three times difference according to the measuring location at the exit of the first rotor due to the partial admission, but they show similar value at the exit of the second rotor by the velocity diffusion. From the measured flow angles and velocities, a ratio of output power obtained by the first and second rotor is estimated. It shows that the output power obtained by the second rotor is about $11\%$ to that by the first rotor at 60,000 RPM. It is effective therefore to improve the first rotor for increasing the turbine output power.

• The KSFM Journal of Fluid Machinery
• /
• v.18 no.6
• /
• pp.37-44
• /
• 2015

Conjugate heat analysis on a high pressure turbine stage including secondary flow paths has been carried out. The secondary flow paths were designed to be located in front of the nozzle and between the nozzle and rotor domains. Thermal boundary conditions such as empirical based temperature or heat transfer coefficient were specified at nozzle and rotor solid domains. To create heat transfer interface between the nozzle solid domain and the rotor fluid domain, frozen rotor with automatic pitch control was used assuming that there is little temperature variation along the circumferential direction at the nozzle solid and rotor fluid domain interface. The simulation results showed that secondary flow injected from the secondary flow path not only prevents main flow from penetrating into the secondary flow path, but also effectively cools down the nozzle and rotor surfaces. Also thermal barrier coating with different thickness was numerically implemented on the nozzle surface. The thermal barrier coating further reduces temperature gradient over the entire nozzle surface as well as the overall temperature level.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.163.1-163.1
• /
• 2011

세계는 지금 지구 온난화 및 화석연료의 고갈로 인해 대체 에너지 자원의 확보문제가 급속히 대두되고 있다. 이에 조류발전은 오염이 발생하지 않는 친환경 에너지원으로서, 날씨나 계절에 상관없이 항상 발전할 수 있는 신뢰성 있는 에너지이며, 높은 밀도를 가지는 작동유체가 수차에 미치는 영향 또한 크므로 지속적으로 예측이 가능한 장점을 가지고 있다. 이러한 조류에너지는 실 해역에 적용하기 위해서는 전격유효 전력이 생산 가능한 지리적 요인에 대한 고찰과 더불어 조류발전 터빈의 개념설계가 고려되어야 한다. 본 연구는 다양한 설치 공간을 형성할 수 있으며, 장, 단점이 보완될 수 있는 조류발전 터빈의 개념설계 연구 단계로서, 내부 유동 특성을 고려하여 입구를 설계하였으며, 일정한 속도로 유입되는 유량을 노즐의 장착을 통해 에너지 밀도를 높일 수 있게 된다. 이러한 개념형상 설계로 추가 작동이나, 장치의 사용 없이 양방향 발전이 가능해 진다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.400-403
• /
• 2007

소형 풍력터빈 설계 시 고려해야 할 익형의 선택, 익형의 붙임각 및 Solidity 등이 터빈의 성능에 미치는 영향을 고찰하였다. 한 개의 익형에 대한 공력계수를 이용하여 수학적 모델링을 통하여 최적 붙임각을 예측하여 경향을 파악하였다. 받음각에 따른 익형의 공력특성을 CFD 기법으로 파악한 후 5개의 Blade를 갖는 Turbine의 성능을 익형의 붙임각에 따라 파악하여 최대 성능을 갖는 붙임각을 최종 산출하였다. 익형 선정시 받음각에 대한 양력/항력 곡선을 이동시키는 캠버 익형의 기능보다는 항력 대양력의 비(L/D) 가 최대인 익형을 선정하는 것이 더욱 중요하며, Blade수가 적을수록 Torque의 양은 증가하고 Blade가 6이상이변 효율이 급격히 감소함을 알 수 있다.

• Proceeding of EDISON Challenge
• /
• 2015.03a
• /
• pp.563-568
• /
• 2015

풍력터변의 성능을 높이기 위한 방법으로 최근 해외에서는 쉬라우드를 장착하여 유입 유량을 증진시키는 형상에 대한 새로운 아이디어가 제안되고 시범적으로 적용되고 있다. 본 연구에서는 쉬라우드가 장착된 수평축 풍력터빈에 대해서 EDISON CFD를 이용하여 쉬라우드 내부로 유입되는 질량 유량의 변동을 몇 가지 형상에 대해 수치적으로 비교 분석하였다. 유동장은 비압축성 난류유동으로 가정하였으며, 수치 해석 결과로부터 쉬라우드 주변의 순환의 세기를 형상 변동에 따라 도출하였다. 쉬라우드 형상으로는 캠버를 갖는 goe 417 에어포일을 두 개의 받음각(5도, 10도)에 대해서 수치해석을 수행하였으며, 브림을 갖는 디퓨저 형상(Wind-lens)에 대해서도 유입 유량 변동과 순환 세기에 대해 수치해석을 수행하고 결과를 상호 비교하였다. 본 연구를 통해 쉬라우드가 발생시키는 순환에 의한 유입 유량 증가 현상을 파악할 수 있었으며, 이로써 풍력터빈의 출력을 증대시킬 수 있음을 확인하였다.