• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.37 no.2
• /
• pp.147-152
• /
• 2001

Corrosion damage of boiler, factory equipment and so forth occur quickly due to using of the polluted water, resulting in increasing leak accident. Especially, working life of hot water boiler using the polluted water becomes more short, and energy loss increases. The cathodic protection method is the most economical and reliable one to prevent corrosion damage of steel structures. Mg-base alloys galvanic anode protection of cathodic protection methode is suitable for the application of hot water boiler using water with high specific resistance such as tap water. This paper is studied on the cathodic protection characteristics of hot water boiler. In tap water solution, the measurement of cathodic protection potential according to the time elapsed is carried out, and behavior of cathodic polarization with current change is investigated. The main results obtained are as follows. In hot water boiler shell, the open circuit potential of base metal become less noble than that of weld Bone, and the current density of base metal becomes low than that of weld zone. The further distance from Mg-alloy galvanic anode, the higher cathodic protection potential of hot water boiler appears. And protective potential becomes high according to pass cathodic protection time and after 6∼10 days become stable.

• Journal of Advanced Marine Engineering and Technology
• /
• v.17 no.1
• /
• pp.55-65
• /
• 1993

Galvanic protection method is one the cathodic protection methods and is mostly used for corrosion prevention of heat exchangers and ship's hull. In this paper, it was investigated that how cathodic potential distribution was varied with according to the bare and painted steel plates in case of galvanic anode protection. The results obtained above were as follows. 1. Cathodic potential distribution of a painted steel plate was smoothed than that of the bare steel plate all over the cathodic surface area. 2. It was shown that polarization potential of the bare steel plate was somewhat shifted to negative potential, on the contrary that of the painted steel plate was somewhat shifted from negative potential to positive potential as time gone by beginning of galvanic anode method. 3. The applied current density in order to maintain constant protection potential(-770mv SCE) in the painted steel plate was less than that of the bare steel plate because of the high resistance polarization of the painted steel plate. 4. It was suggested that required number and life-time of anode for galvanic anode protection could be decided easily with corrosion prevention coefficient obtained by experimental data.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2000.05a
• /
• pp.115-121
• /
• 2000

As the development of industry water quality of river is going to bad because of waste water of an industrial complex and general home agricultural chemicals exhaust of $SO_3$ and CO gas acid rain and so on. Corrosion damage of boiler factory equipment and so forth occur quickly due to using of the polluted water resulting in increasing leak accident. Especially working life of hot water boiler using the polluted water becomes more short and energy loss increases. The cathodic protection method is the most economical and reliable one to prevent corrosion damage of steel structures. Mg-base alloys galvanic anode protection of cathodic protection method is suitable for than application of hot water boiler using water with high specific resistance such as tap water. This paper is studied on the cathodic protection characteristics of how water boiler. In tap water and 0.001mol/$\ell$ NaCl solution the characteristics of anodic polarization of Mg-base alloys galvanic anode and tube material is investigated the measurement of cathodic protection potential according to the time elaspsed is carried out.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.133-133
• /
• 2000

알루미늄 산화막은 알루미늄 전해 커패시터의 유전재료로 많이 사용되고 잇다. 기존의 생산 공정은 양극 산화법에 의한 산화막 형성으로 대부분이 이러한 습식 공정으로 생산되고 있다. 이 양극 산화법 방식은 장점도 있으나 폐기물이 많이 발생되는 단점이 있다. 본 연구에서는 폐기물의 발생을 획기적으로 줄일 수 있고 산화막 형성 효율을 높일 수 잇는 방식으로 activated reactive evaporation(ARE)을 도입하였다. 이 방식은 electron-beam에 의해 알루미늄을 증착시킬 때 plasma를 챔버 내에 발생시켜 활성 반응으로 알루미늄 원자가 산소와 반응하여 기판위에 Al2O3가 증착되는 것이다. 이 방식은 기계적 작동이 단순하고 증착이 되는 여러 변수들의 독립적 조절이 가능하므로 증착을 제어하기 쉽기 때문에 바로 산업 현장에서 적용될 수 있을 것으로 전망되어 본 연구에 도입하게 되었다. 기판은 유전용량을 증가시키기 위하여 알루미늄 원박을 에칭하였다. 이것은 기판으로 쓰일 알루미늄의 표면의 표면적을 증가시키기 위한 것으로, 알루미늄 전극의 표면적을 확대시키면 유전용량이 증가된다. 99.4%의 50$\mu\textrm{m}$와 60$\mu\textrm{m}$ 두께의 알루미늄 원박을 Ar 이온빔에 의해 1keV의 에너지로 20mA로 에칭을 하였다. 에칭 조건별로 에칭상태를 조사하였다. 에칭 후 표면 상태는 AFM으로 관찰하였다. 화성 실험은 진공 챔버 내의 진공을 약 10-7 torr까지 내린 후, 5$\times$10-5 torr까지 O2와 Ar을 주입시킨 다음 filament에서 열전자를 방출시키고 1.2 kV의 electrode에 의해 가속시켜 이들 기체들의 플라즈마를 발생시켰다. e-beam에서 증발된 알루미늄과 활성 반응을 이루어 기판에 Al2O3가 형성되었다. 여러 증착 변수들(O2와 Ar의 분압, 가속 전압, bias 전압 등)과 산화막의 상태 등을 XPS(X-ray photoelectron spectroscopy), AFM(Atomic Force Microscopy), XRD(X-Ray Diffraction), EXD로 조사하였다.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.19 no.1
• /
• pp.57-62
• /
• 1983

The galvanic anodes have three kinds of Zn alloy anode, Al alloy anode and Mg alloy anode, which are widely used in cathodic protection for all metal structures in water or under ground. This paper to be used for designing of the grounding cell has reached the following conclusion as the results of an experimental study on the characteristics of such galvanic anodes for corrosion protection of pipings: 1) Zn alloy anode was the best when the specific resistance of the environment was bellow 1000 $\Omega$.cm, and when above 1000 $\Omega$.cm, Mg alloy anode to be used for designing of the grounding cell was the best. 2) Al alloy anode was better than Mg alloy anode for grounding cell when the specific resistance was bellow 500 $\Omega$.cm, but the Al alloy anode in all the environments reduced the characteristics of galvanic anode to the lower grade than those of Zn alloy anode. 3) Each impressed voltage (E) of the anodes at which drainage current density ($\rho$) begins rapidly increasing is quantitatively presented as follows: \circled1 E sub(Zn)=log (4.9465/$\rho$super(0.0639))+11$\times$10 super(-6)$\rho$super(0.8923i) \circled2 E sub(Al)=log (4.9306/$\rho$super(0.0525))+13$\times$10 super(-6)$\rho$super(0.9314i) \circled3 E sub(Mg)= log (3.7086/$\rho$super(0.0988))+181$\times$10 super(-6)$\rho$super(0.5406i) 4) The empirical equations between the drainage current density (i) and impressed environment are modeled as the following type. logi=g+root(n.E+r)(g,n,r; constants)

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2001.05a
• /
• pp.152-157
• /
• 2001

This paper was studied on the characteristics of crevice corrosion prevention of SS 400 in marine environment. In NaCl solution, polarization behavior under the crevice corrosion was investigated. And Weight loss rate of SS 400 applied cathodic protection and non cathodic protection was measured according to the NaCl concentration. The main results obtained are as follows : The weight loss rate of Al-alloy galvanic anode was increased as the concentration of NaCl solution increased by 3.5% but the concentration increased over 3.5%, that of Al-alloy galvanic anode become decreased. The protective potential of SS 400 used Al-alloy galvanic anode becomes more cathodic polarization with increasing concentration of NaCl solution. Effects of oxygen on the weight loss rate of Al-alloy sacrificial anode for cathodic protection as the concentration of 3.5% NaCl solution become sensitive than that of 0% NaCl solution.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.4
• /
• pp.69-74
• /
• 2010

A new package substrate for dynamic random access memory(DRAM) devices has been developed using selective aluminum anodization. Unlike the conventional substrate structure commonly made by laminating epoxy-based core and copper clad, this substrate consists of bottom aluminum, middle anodic aluminum oxide and top copper. Anodization process on the aluminum substrate provides thick aluminum oxide used as a dielectric layer in the package substrate. Placing copper traces on the anodic aluminum oxide layer, the resulting two-layer metal structure is completed in the package substrate. Selective anodization process makes it possible to construct a fully filled via structure. Also, putting vias directly in the bonding pads and the ball pads in the substrate design, via in pad structure is applied in this work. These arrangement of via in pad and two-layer metal structure make routing easier and thus provide more design flexibility. In a substrate design, all signal lines are routed based on the transmission line scheme of finite-width coplanar waveguide or microstrip with a characteristic impedance of about $50{\Omega}$ for better signal transmission. The property and performance of anodic alumina based package substrate such as layer structure, design method, fabrication process and measurement characteristics are investigated in detail.