• Tribology and Lubricants
• /
• 제24권6호
• /
• pp.355-361
• /
• 2008

In highly stressed machine elements such as angular contact ball bearings and toroidal type traction drives, the elastohydrodynamic lubrication of elliptical contacts with both rolling and spinning motion are occur. In this paper, a finite difference method with non-uniform grid systems and the Newton-Raphson method are applied to solve the problems. Pressure distributions, film contours and variations of the minimum and central film thicknesses are compared with various ellipticity parameter, dimensionless speed and load parameter. The results showed that the spinning motion has significant influence especially on the film shapes. Reduction of the minimum film thickness under spinning is remarkable whereas the central film thickness is relatively less. Especially variations of the minimum film thicknesses with rolling velocity, load and ellipticity ratio are a great different from those of pure rolling. Therefore present numerical scheme can be used in the analysis of general elliptical contact EHL problems and further studies are required.

• 한국정밀공학회지
• /
• 제28권4호
• /
• pp.410-415
• /
• 2011

A cylindrical type of self-controlled restrictor is designed for hydrostatic bearing of crank shaft for a grinding wheel spindle. The effect of operation parameters, clearance between spindle and housing on bearing stiffness are analyzed to determine the optimum conditions of operation parameters. The lowest values of the supply pressure and the loads by the theoretical and experimental results assuming oil film thickness and shape of pocket are compared.

• 한국자동차공학회논문집
• /
• 제2권4호
• /
• pp.9-17
• /
• 1994

Effect of Newtonian and non-Newtonian oils on minimum ol film thickness in engine journal bearing were investigated at various oil viscosities. The influence of oil viscosity and engine operating conditions on minimum oil film thickness of main bearing and con-rod bearing was examined. Minimum oil film thickness for Newtonian oils increased uniformly with kinematic viscosity. But the correlation between kinematic viscosity and minimum oil film thickness was very poor for non-Newtonian oils. According to the straight-line regression analysis for non-Newtonian oils, high temperature high shear viscosity at 1 $1{\times}10^6Sec^{-1}$, $150^{\circ}C$ increase the coefficient of determination from 0.41 to 0.77. Con-rod bearing showed better correlation between minimum oil film thickness and engine operating conditions than main bearing.

• 한국자동차공학회논문집
• /
• 제2권5호
• /
• pp.1-10
• /
• 1994

By applying of total electric capacitance method on engine connecting rod bearing during engine operating, the influence of engine operating conditions and lubricants on bearing oil film thickness was investigated. Minimum oil film thickness increases with kinematic viscosity, but as increasing of viscosity, the increasing ratio of film thickness is reduced. Also minimum oil film thickness increases with engine speed but there is a limit. Above this limit, film thickness decreases in opposition because of crankshaft inertia. As increasing of engine torque and oil temperature, munimum oil film thickness decreases linearly. For non-Newtonian oils, the correlation between $100{\circ}C$ kinematic viscosity and munimum oil film thickness is very poor.

• 한국유체기계학회 논문집
• /
• 제9권5호
• /
• pp.7-13
• /
• 2006

In the present study, we develop an analysis module to be applicable to design of sliding thrust bearings. The pressure equation is solved by using the finite element method. Average lubricant temperature is obtained from using the energy balance method. The module developed has been applied to three types of thrust bearing, such as tapered-land thrust bearings of angular and diamond types, and tilting-pad thrust bearings. Effects of the dam of the tapered-lad thrust bearings have also been investigated. It has been seen that the tapered-land thrust bearings of angular type result in the highest load capacity, while the tilting pad thrust bearings result in the lowest lubricant temperature. It has also been seen that the dam in the tapered-land thrust bearings increases both the load capacity and lubricant temperature.

• 동력기계공학회지
• /
• 제15권5호
• /
• pp.5-9
• /
• 2011

The hydraulic piston using a hydrostatic bearing has been used widely due to its satisfying performance at very high pressurized circumstance and relative higher power density in comparison to conventional one. For high pressurization, enhanced efficiency and long durability of the hydraulic piston, the design of hydrostatic bearing is at issue, which is installed between piston shoe and swash plate. The performance of the hydrostatic bearing is influenced significantly by the assembly of the piston shoe consisting of circular land and recess. In this study, to estimate the performance of the hydrostatic bearing, the characteristics for lubrication of the assembly of the piston shoe were investigated by measuring a leakage rate of hydraulic fluid under an experimental condition, where a rotating velocity of the piston, hydraulic pressure and temperature of the hydraulic fluid were changed systematically. In addition, a film thickness of the hydraulic fluid on the piston shoe was measured and compared to theoretical one.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2001년도 제33회 춘계학술대회 개최
• /
• pp.218-223
• /
• 2001

Many research of elastohydrodynamic lubrication (EHL) has been performed under the condition of steady state loding. However, mechanical elements undergo severe high loads that are fluctuating in general. Conventional numerical method for the circular contact of EHL study has a difficulty in converging the film pressure and thickness especially in high load of steady state. In this work, multigrid multilevel method expels the convergence problem under the condition of high load and very stable convergence is obtained under the dynamic loading condition over 1.0GPa. Several results of dynamic loading condition are shown and compared with those of steady state condition.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집C
• /
• pp.293-298
• /
• 2001

In this paper, film thickness and temperature distribution are measured in EHL point contact at high roll/slip ratios. Infrared temperature mapping with two band pass filters, proposed by Ausherman (1976), is used to measure temperature distribution. And the optical interferometric method with two filters (red and green filters) is used to measure film thickness. Result of experiment showed that temperature rising at film and ball surface occurred very dramatically in Dimple zone. As slip velocity, roll/slip ratio and load increased, size of Dimple and temperature rising became more large. In addition, position and shape of Dimple were changed by roll/slip ratios, and increasing of Dimple size decreased traction coefficient. In short, it is appointed that the Dimple phenomenon be developed by the effect of viscosity wedge.

• 한국자동차공학회논문집
• /
• 제3권6호
• /
• pp.55-68
• /
• 1995

Approximately 30 to 70 % of the mechanical losses in a reciprocating engine are contributed by the friction at the piston ring-cylinder interface. The friction characteristics of the piston ring during engine operation is known to as mixed lubrication experimentally. The mixed lubrication models based on the Average Reynolds Equation have been used by this time in order to study the tribological performance of the ring. However, the Average Reynolds Equation contains the expected value term(${\bar{h}}_r$) of local film thickness as well as nominal film thickness(h), so that the work of numerically solving ${\bar{h}}_r$ must be included to obtain the pressure in the oil film. The process of solving ${\bar{h}}_T$ causes a greater multiplying in the numerical solution. In this paper the mixed lubrication analysis using the Simplified Average Reynolds Equation in the piston ring is presented. This equation has only h as oil film thickness term. Therefore the tedious numerical procedure required to obtain ${\bar{h}}_T$ is not needed, and also, computation time can be reduced.

• Tribology and Lubricants
• /
• 제38권5호
• /
• pp.199-204
• /
• 2022

This paper presents a numerical investigation of the influence of water molecule thickness on frictional behavior at the nanoscale using molecular dynamics simulation. Three different models, comprising water thin films of various thicknesses, were built, and indentation and sliding simulations were performed using the models. Various normal loads were applied by indenting the Si tip on the water film for the sliding simulation to evaluate the interplay between the water thin film thickness and the normal load. The results of the simulations showed that the friction force generally increased with respect to the normal load and thickness of the water thin film. The friction coefficient varied with respect to the normal load and the water film thickness. The friction coefficient was the smallest under a moderate normal force and increased with decreasing or increasing normal loads. As the water film became thicker, the contact area between the tip and water film became larger. Under well-lubricated conditions, the friction force was proportional to the contact area regardless of the water film thickness. As the normal force increased above a critical condition, the water molecules beneath the Si tip spread out; thus, the film could not provide lubrication. Consequently, the substrate was permanently deformed by direct contact with the Si tip, while the friction force and friction coefficient significantly increased. The results suggest that a thin water film can effectively reduce friction under relatively low normal load and contact pressure conditions. In addition, the contact area between the contacting surfaces dominates the friction force.