• Resources Recycling
• /
• v.29 no.3
• /
• pp.51-60
• /
• 2020

This study was carried out to get the optimum conditions for manufacturing high refractive glass beads from waste fluorescent lamp glass. Chemical composition, X-ray diffraction pattern, particle size distribution, refractive index of glass beads, and the effect of air mixing ratio and ejection rate were investigated. The obtained results are as follows. The X-ray diffraction pattern and chemical composition of glass beads made of waste fluorescent glass are similar to common glass except ReO₂ 0.0108 wt%, BaO 0.071 wt%, NiO 0.0039 wt% and CaO 7.8 wt% but 11.7 wt% of common glass. The glass beads made of waste fluorescent lamp glass have the narrower particle size distribution of and the higher refractive index than the glass beads made of common glass. The optimal conditions of kiln operation for manufacturing glass beads from waste fluorescent lamp glass are 20 m/sec of ejection rate, 1.7 of air mixing ratio, and 940℃ of temperature.

• Polymer(Korea)
• /
• v.37 no.5
• /
• pp.656-662
• /
• 2013

The flexible patterned cover film was made by a simple solution coating process using polymethyl methacrylate (PMMA) solution with glass beads. The effect of patterned cover film on the efficiency of solar cell has been investigated. It was found that the relative solar cell efficiency increased up to 3.4% with the incident light angle between $0-90^{\circ}$ by the sphere shape of glass bead coated on the film surface. This was understood that the loss of transmittance and scattering due to the light directional dependency on solar cell were minimized because the light entered glass beads normal to its surface regardless of incident light angle. The maximum relative solar cell efficiency was achieved when glass bead shape on the film is hemisphere and the relative efficiency increased with increasing the amount of glass bead on the film surface. However, too much glass beads on the film surface resulted in the lower relative solar cell efficiency due to the lowering of transmittance as well as the occurring of light interference.

• Journal of Adhesion and Interface
• /
• v.19 no.2
• /
• pp.68-73
• /
• 2018

In this study, conductive EVA foams including multi-wall carbon nanotubes (MWCNT), glass beads were prepared. The electrical conductivity and physical properties of the foams were confirmed with varying amount of MWCNT, mixing time, and amount of glass beads. The electrical conductivity increased with the amount of MWCNT. Dispersity of MWCNT in EVA foams were improved with glass beads. It can be suggested that conductive EVA foams can be successfully prepared with improved dispersity of MWCNT in ethylene-vinyl acetate by using glass beads.

• KSBB Journal
• /
• v.24 no.5
• /
• pp.432-438
• /
• 2009

Here, we demonstrated simple nucleic acid, RNA, concentration method using polymer micro chip containing glass bead ($100\;{\mu}m$). Polymer micro chip was fabricated by PDMS ($1.5\;cm\;{\times}\;1.5\;cm$, $100\;{\mu}m$ in the height) including pillar structure ($160\;{\mu}m\;(I)\;{\times}\;80\;{\mu}m\;(w)\;{\times}\;100\;{\mu}m\;(h)$, gap size $50\;{\mu}m$) for blocking micro bead. RNA could be adsorbed on micro glass bead at low pH by hydrogen bonding whereas RNA was released at high pH by electrostatic force between silica surface and RNA. Amount of glass beads and flow rate were optimized in aspects of adsorption and desorption of RNA. Adsorption and desorption rate was measured with real time PCR. This concentrated RNA was applied to amplification micro chip in which NASBA (Nucleic Acid Sequence Based Amplification) was performed. As a result, E.coli O157 : H7 in the concentration of 10 c.f.u./10 mL was successfully detected by these serial processes (concentration and amplification) with polymer micro chips. It implies this simple concentration method using polymer micro chip can be directly applied to ultra sensitive method to measure viable bacteria and virus in clinical samples as well as environmental samples.

• Proceedings of the KAIS Fall Conference
• /
• 2007.05a
• /
• pp.261-263
• /
• 2007

본 연구는 광전자 촉매시스템을 이용해 $TiO_{2}$ 졸이 코팅된 구형 비드의 광분해 효율에 대해 고찰한 것이다. $TiO_{2}$ 졸이 코팅된 구형 비드인 알루미늄비드, 유리비드, 실리카비드 화이트젤 ($1{\cdot}2{\cdot}3$형) 다섯 가지 비드를 사용하였고 실험은 산화환원지시 약인 메틸렌블루 수용액이 광촉매의 산화환원반웅을 통해 색상 및 홉광도 변화를 통해 환원 청도를 고찰할 목적으로 실행되었다. 소재별 실험 결과, 실험에 사용한 소재 중 실리카비드 화이트첼($1{\cdot}2{\cdot}3$형)만이 반응성을 나타냈다. 이들 $1{\cdot}2{\cdot}3$형은 $TiO_{2}$의 함량을 달리한 비드들이며 1형이 가장 적은 함량을 가지며 3형이 가장 많은 함량을 가지고 있다. 실험 결과 3형이 반응성이 가장 좋은 것을 알 수 있으며, 이 실험에서는 코팅물의 함량과 고정물의 상태가 광촉매 반응에 영향을 주는 것을 알 수 있다.

• Journal of the Korean Vacuum Society
• /
• v.22 no.6
• /
• pp.298-305
• /
• 2013

Uniform silica nanobeads were synthesized by St$\ddot{o}$ber method and assembled in the form of monolayer on glass substrate using sonication method. Before the assembly of silica nanobeads, glass substrates were treated with molecular linkers, such as CP-TMS and PEI, and nanobeads were dispersed in toluene. In attachment test, SO (sonication without stacking) method and SS (sonnication with stacking) method was used and sonication time was controled. After the experiment, microbalance was use to measure deviation between before and after the attachment experiment then calculate percent of coverage. Minutely observe with SEM (Scanning Electron Microscopy) then select the most close-packed and monolayer assembled cover glass and calculate DOC (Degree of Coverage). In SO method, DOC increased very sharply and reach over 140 percent point, also got lots of multi-layer region. On the other hand, in SS method DOC increased slower than SO method but more close-packed and monolayer assembled.

• Korean Chemical Engineering Research
• /
• v.53 no.6
• /
• pp.792-797
• /
• 2015

Graphene has a wide spectrum on its application field due to various and excellent physical properties. However, it is very difficult to apply that graphene exists as lump or fold condition in general organic solvents. Besides, graphene was difficult to maintain as uniform condition due to chemical inert and distributions with various size and shapes. Therefore, this study was focused to study dispersion and modifying methods of aggregated graphene. The dispersion methods contain as follow: i) physical milling using glass bead, ii) co-treatment of glass bead and ultrasonic waves, iii) dispersion in organic solvents, iv) modifying with dry-ice. Milling using glass bead with size 2.5 mm was effective to be size decrease of 36.4% in comparison with control group. Mixed treatment of glass bead (size 2.5 mm) and ultrasonic waves (225W, 10 min) showed relative size decrease of 76%, suggesting that the size decrease depends on the size of glass bead, intensity of ultrasonic waves and treatment time. Solvents of Ethyl acetate (EA) and Isoprophyl alcohol (IPA) were used in order to improve dispersion by modifying surface of graphene. IPA of them showed a favorable dispersion with more -CO functional groups in the FT-IR analysis. On the other hand, the oxygen content of graphene surface modified by dry-ice was highly increased from 0.8 to 4.9%. From the results, it was decided that the favorable dispersion state for a long time was obtained under the condition of -CO functional group increase in IPA solvent.

• Proceedings of the KAIS Fall Conference
• /
• 2005.05a
• /
• pp.274-276
• /
• 2005

본 논문에서는 유동층 화학기상증착법(FB CVB; Fluidized Bed Chemical Vapor Deposition)으로 광촉매가 박막증착된 비드를 제조하였고 제조된 광촉매코팅비드의 광반응성을 연속식 반응기에서 아세트알데히드의 분해능력을 측정하여 분석하였다. 광촉매가 박막증착된 비드의 FE-SEM 분석 결과 글라스 비드 위의 티타니아는 비교적 매끄럽게 증착되었고, 실리카 위의 티타니아는 입자의 형태로 증착되었으며 알루미나 위의 티타니아는 결정상을 이루며 증착됨을 확인 할 수 있었다. Acetaldehyde 기체의 광촉매에 의한 분해 실험을 진행하기 위해 연속식 반응기를 설계 제작하였고, 이 반응기를 사용하여 제조된 광촉매 코팅입자의 광반응성을 살펴보았다. 반응기는 가스 주입구와 출구를 갖고 있으며, 중심부에 UV 램프가 설치되었다. 반응기는 내열유리(pyrex)로 제작하였으며, 체적은 100 ml이다. 반응기 내부의 중심부에 UV 램프가 설치되고 UV 램프와 반응기 외부사이에 유동층 화학기상증착법에 의해 티타니아가 박막증착된 광촉매입자가 위치하여 광반응성을 평가하였다. 유량변화에 따른 광반응성을 측정하였으며, 알루미나에 광촉매를 증착시킨 제품의 경우 가스유량 100cc/min에서는 acetaldehyde가 $100\%$ 분해되고, 가스유량 500cc/min에서는 $50\%$정도 분해되는 것을 알 수 있었다.

• Proceedings of the KWS Conference
• /
• 2010.05a
• /
• pp.40-40
• /
• 2010

산업현장에서는 파이프 또는 탱크류의 1GR용접에서 안정적인 이면비드를 가지는 루트패스 용접을 위해 2~3mm의 루트갭을 띄우고 용접봉 또는 필러와이어를 사용하는 TIG용접을 주로 한다. TIG용접은 고품질의 이면비드가 얻어지며, 용접인자의 제어가 쉽다는 장점이 있어 루트패스 용접에 많이 사용되고 있지만, 루트갭을 띄우면 이면비드는 잘 얻어지지만 용착금속량이 많아지게 되어 제작원가가 상승되고, 또한 소모성 와이어를 사용하는 GMAW에 비해 생산성이 낮다. 따라서, 안정적인 이면비드를 가지면서 생산성이 높은 1GR GMAW 루트패스 용접공정의 개발이 요구되지만, 이 경우도 루트갭이 2~3mm로 정해져 있으면 Fit-up공정에서 공수가 많이 필요하므로 근본적으로 루트갭이 없는 그루브에 대한 루트패스 용접이 더 바람직하다. 본 연구에서는 루트면 2.7mm를 가지는 U-그루브의 갭 없는 루트패스 용접에서 안정적인 이면비드가 형성되는 조건을 검토하기 위해 2.7t의 평판에 대하여 경사상진 각을 주고 기초 실험 후, U-그루브 맞대기 용접 실험을 진행하였다. 이 때, 경사상진 각은 용융금속이 중력으로 인해 아크 후방으로 밀리게 되고, 그로 인해 아크가 모재에 직접 닿게 되어 용입이 더 깊게되므로, 이면비드의 형성에 더 유리하다. 두께 2.7t의 연강 시편 2개를 갭 없는 I-그루브 맞대기 이음에서 Ǿ1.2 연강 솔리드 와이어를 사용하여 GMAW용접을 실시하였고, 용접전류, 용접속도, 경사상진 각, 위빙 폭, 위빙 주파수를 변경하여 각 조건에 대한 이면비드를 관찰하였다. 그 결과 경사상진 각 $25^{\circ}$, 전류 200A, 위빙폭 3mm, 위빙주파수 3Hz의 조건에서 안정적인 이면비드를 얻을 수 있었다. 또한, 현장에서 Fit-up중 발생할 수 있는 루트갭의 문제에 대하여 루트갭 1.2mm의 I-그루브 맞대기 용접에서 경사상진 각, 위빙 폭, 위빙 주파수는 갭 없이 실시한 실험에서 얻어진 가장 안정적인 결과를 사용하였고, 용접 전류, 용접 속도를 변경하여 이면비드를 관찰하였다, 그 결과 갭이 없을 때보다 약 80A 낮은 전류 조건인 120A에서 안정적인 이면비드를 얻을 수 있었다. 앞선 실험들을 기초로 하여 U-그루브 맞대기 용접을 실시 하였고, I-그루브 맞대기 용접에서 사용한 조건들과 유사한 용접 전류, 용접 속도에서 안정적인 이면비드를 얻을 수 있었다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.12 no.1
• /
• pp.207-217
• /
• 1992

In this study, isolated and cultured nitrogen fixed microbes were seeded in the three-phase fluidized bed in which gas, solid and liquid were contacted directly. Input velocity was varied from 8.12 cm/hr to 16.32 cm/hr. And upflow gas pressure was fixed to 80 psi. Return ratios were from 0.2 to 0.6 with the each experimental condition. According to these condition, movement of media, growth of biofilm and removal efficiency were measured. As the results, in case of briquette ash, biofilm was developed to $170{\mu}m$ when velocity was 8.12 cm/hr and return ratio was 0.6. In this condition, COD removal efficiency was 97% and $NH_4$-N removal efficiency was 83%. At the same condition, biofilm thickness of glass bead was $17.59{\mu}m$ and its COD and $NH_4$-N removal efficiency was 83% and 72%. Nitrogen fixed microbes have following characters: it formed dark-brownish sludge, excellent adhesive force, easy solid-liquid separation and low oxygen uptake ratio, but sensitive to DO concentration. Not only it endured shock loading, but required short time to steady state.