• Proceedings of the Korea Water Resources Association Conference
• /
• 2017.05a
• /
• pp.132-132
• /
• 2017

큰 하상계수를 가지는 국내 중소하천의 특성상 농업용수 등의 수자원 이용을 위해 국내에는 약 10,000개 정도의 하천 횡단구조물이 설치되어 있다. 그러나 느려진 유속으로 인하여 횡단구조물 상류에 유사가 퇴적될 확률이 높아지며, 이러한 유사는 부착된 오염물에 의한 수질 및 하상오염, 좁아진 유수단면적에 의한 통수능 저하로 발생하는 홍수위 증가 등 많은 위험성을 내포하고 있다. 이에 대한 해결책 중의 하나로 저층수 배사관(bypass pipe)을 활용하여 쌓여진 유사를 하류로 흘려보내는 방법이 있다. 저층수 배사관은 횡단구조물 상류와 하류의 하상을 연결하는 관으로써 상류와 하류의 수두차에 의해 흐름 특성이 결정된다. 하지만 배사관 내 사석이 유입되어 배제되지 않는 경우 배사관의 효율이 현저하게 저하될 가능성이 있다. 본 연구에서는 FLOW-3D를 이용하여 배사관내 사석이 유입되었을 때, 어떠한 조건에서 배제되고 배제되지 않는지를 명확히 하고자 한다. 하상이 평탄한 수로$(13.0(L){\times}5.0(B){\times}1.0(H)m)$를 재현하였으며, 배출관의 직경은 10cm로 결정하였다. 사석의 종류는 4가지(3cm, 5cm, 7cm, 9cm)로써 이를 고려하여 격자크기를 0.5cm로 결정하였다. 이는 사석의 구형형상이 충분히 잘 재현될 수 있는 격자크기이다. 모의 수행은 하류의 수위를 변화시켜가며 수행하였다. 저층수 배사관 내 유동 특성이 상류와 하류의 수두차에 의해 결정되기 때문에, 모의의 효율성을 위해 상류의 수위는 일정한 값으로 진행하였다. 모의 결과 수위차가 클수록 배제가 잘되는 경향을 보였다. 입자의 크기와 상하류 수위차를 무차원화 한 변수를 결정하였다. 분석결과 이 변수가 일정 값을 넘어서는 경우 배제가 되며, 반대로 이 값을 넘어서지 못한 경우 배제가 되지 않음을 확인하였다. 향후 다양한 관의 형상에 대해서도 배사관 내 한계조건을 도출하여, 저층수 배사관의 설계 및 시공에 도움이 되고자 한다.

• Journal of the Korean Geotechnical Society
• /
• v.35 no.4
• /
• pp.37-42
• /
• 2019

Hydrate dissociation is required to produce methane, which generates both water and methane. Thus, multiphase fluid flow and desalination are expected during methane production, which causes the fine migration and clogging in pores. The goal of this study is to explore the effects of both multiphase fluid flow and desalination on the migration and clogging of kaolin particles as typical fines. The results are as follows : (1) the larger the pore size is, the more mounting the critical clogging concentration is, (2) kaolin particles are more easily clustering and clogging in deionized water than salty water, and (3) the critical clogging concentration of kaolin in multiphase fluid flow is lower than in singlephase fluid flow. Therefore, clustering and clogging of kaolin within pore occur easily due to desalination and multiphase fluid flow when methane is produced from hydrates, and the efficiency of methane production is expected to decrease due to the degradation of permeability coefficient.

• Applied Chemistry for Engineering
• /
• v.30 no.1
• /
• pp.95-101
• /
• 2019

The cremation rate of Korea in 2016 was 82.7% which is four times greater than 20.5% in 1994. As increasing the cremation rate gradually, it cause a shortage of cremation facilities resulting in building more cremation facilities to meet the increasing inquiries on cremation or a large amount of fuels for the longer operation of the crematory. In this study, the crematory system optimizing its thermal efficiency characteristics and also responding to increasing inquiries on cremation was proposed in order for solving such problems, In particular, the heat flow characteristics including a heat transfer coefficient by performing a simulation using computational fluid dynamics (CFD) was investigated. The CFD model was validated with on-site experiments for a cremation facility. As a result of the simulation, the fuel consumption decreased nearly 25% and residence time increased in the main combustor. Also, the improved crematory was constructed with an expanded combustor, heat exchanger, second combustion air system, refractory and insulation material. From on-site experiments, the energy consumption was saved to approximately 54.4%, while the burning time reduced nearly 20 minutes.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.45 no.5
• /
• pp.881-891
• /
• 2021

This study proposes a simple drape measurement method for the 3D virtualization of garments. The proposed method uses angles or disks of different diameters to evaluate the drape properties easily. We divided 710 fabrics into ten groups based on the drape coefficient, of which 49.6% had drape coefficients of 30 or less. The drape properties were measured to classify the groups into smaller clusters using the angle formed when the center of the fabric was fixed. Accordingly, three clusters were formed for 60° and 100° angles. A method was devised using ten disks of different diameters to classify the remaining two clusters, except the cluster containing only the D10 group (D1-D5 and D5-D9). Three criteria-grade match, a sum of deviation, and standardization of deviation-were used for the classifications. The discriminative ability between groups was high for D1-D5 with disks with 24.0 and 25.5 cm diameters. Furthermore, a disk with a diameter of 16.5 cm was effective for D5-D9. The three-dimensional drape shapes were unique for the ten groups, which can be utilized as fundamental data for 3D virtualization.

• Journal of the Korean Society of Visualization
• /
• v.20 no.3
• /
• pp.94-101
• /
• 2022

The evaluation of the drag and lift as the aerodynamic performance of airfoils is essential. In addition, the analysis of the velocity and pressure fields is needed to support the physical mechanism of the force coefficients of the airfoil. Thus, the present study aims at establishing two different deep learning models to predict force coefficients and flow fields of the airfoil. One is the convolutional neural network (CNN) model to predict drag and lift coefficients of airfoil. Another is the Encoder-Decoder (ED) model to predict pressure distribution and velocity vector field. The images of airfoil section are applied as the input data of both models. Thus, the computational fluid dynamics (CFD) is adopted to form the dataset to training and test of both CNN models. The models are established by the convergence performance for the various hyperparameters. The prediction capability of the established CNN model and ED model is evaluated for the various NACA sections by comparing the true results obtained by the CFD, resulting in the high accurate prediction. It is noted that the predicted results near the leading edge, where the velocity has sharp gradient, reveal relatively lower accuracies. Therefore, the more and high resolved dataset are required to improve the highly nonlinear flow fields.

• Plant Journal
• /
• v.18 no.2
• /
• pp.41-45
• /
• 2022

The conventional communication method using mud flow pressure waves has a speed of 1-2 bps, so it takes a long time to communicate, making real-time control impossible. Although the sound wave communication method for improving the communication speed by 10 times or more has been commercialized, its use is limited due to its high price and there are not many application cases. In this study, the simulator corresponding to the facility was developed to develop performance similar to the actual test results. For simulating sound wave communication through a drill pipe, we proposed a governing equation that can simulate friction damping by mud and developed a numerical analysis model. The attenuation factor was corrected by comparing it with the attenuation rate of sound wave energy at the drilling site. The developed numerical analysis model was applied to the QPSK modulation type communication algorithm to confirm the excellent performance of the communication error rate of 0.04% in the ground. This is the communication performance under the condition that noise has not been mixed yet, and in order to apply it, the technology of reproducing the actual noise signal for mixing by securing the field noise data was established.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.4
• /
• pp.47-55
• /
• 2008

This study was carried out to investigate and analyse the influence of maximum size of coarse aggregate and quality control of aggregate on the properties of shotcrete through the laboratory and field test. From the results of the test, as the maximum size of coarse aggregate decreased from 13 mm to 8 mm, plasticity property declined and compressive strength and dynamic modulus of elasticity of hardened concrete increased remarkably, so it was found that the aggregate size 8 mm was superior to 13, 10 mm in fluidity, constructability and durability. Therefore, it was advisable for well maximum size of coarse aggregate to apply to the 8mm aggregates through the Ready-mixed Method for quality control and minimum segregation.

• The Journal of the Acoustical Society of Korea
• /
• v.29 no.4
• /
• pp.243-250
• /
• 2010

This paper proposes a spectral modeling of Korean traditional instrument, Haegeum, using cepstral analysis to naturally describe Haegeum sounds varying with time. To get a precise result of cepstral analysis, we set the frame size to 3 periods of input signal and more cepstral coefficients are used to extract formants. The performance is enhanced by flexibly controlling the cutoff frequency of bandpass filter depending on the resonances in the synthesis process of sinusoidal components and the deleting peaks remained in the residual signal. To detect the change of pitch, we divide the input frames into silence, attack, and sustain region and determine which region the current frame is involved in. Then, the proposed method readjusts the frame size according to the fundamental frequency in the case of the current frame is in attack region and corrects the extraction errors of the fundamental frequency for the frames in sustain region. With these processes, the synthesized sounds are much more similar to the originals. The evaluation result through the listening test by a Haegeum player says that the synthesized sounds are almost similar to originals (96~100 % similar to the original sounds).

• Korean Journal of Plant Resources
• /
• v.28 no.1
• /
• pp.101-110
• /
• 2015

Parameters of mating system and pollen flow of a Pinus densiflora population in Buan, South Korea, were estimated using seven nuclear microsatellite markers. The expected heterozygosity ($H_e$) was 0.614 in mother trees and 0.624 in seeds. Fixation index (F) was 0.018 and 0.087 in each generation. There was no significant genetic difference between the generations (P > 0.05). From MLTR, the outcrossing rate ($t_m$), the biparental inbreeding ($t_m-t_s$), and the correlation of paternity ($r_p$) were 0.967, 0.057, and 0.012, respectively. tm was larger but $t_m-t_s$ and $r_p$ were smaller than those of allozyme markers in Pinus densiflora. These values were similar to those of microsatellite markers in other pine species. The optimal pollen dispersal model from TwoGener was the normal dispersal model with the effective density of 220 trees/ha and its level of genetic differentiation in pollen pool structure (${\Phi}_{ft}$) was 0.021. The average radial distance of pollen flow (${\delta}$) was calculated as 11.42 m, but no correlation between the pairwise-${\Phi}_{ft}$ and the geographical distance among mother trees was at Mantel test (r = -0.141, P > 0.05). Although the effective pollen dispersal in the population seems to be restricted, the amount of genetic variation might be maintained in each generation without a loss of genetic diversity. It might be because the genetic diversity in pollen pool was high but the genetic difference between pollen donors was small under the complete random mating condition in the Pinus densiflora population in Buan.

• Journal of Korean Society of Forest Science
• /
• v.80 no.1
• /
• pp.72-81
• /
• 1991

This study was carried out to provide necessary information for improving quarrying industry management in Korea. The results of the study are summarized as follows : 1. In aggregate and building-stone quarrying firms the managers over 40 years of age are 97% and 89.1%, the ones above education level of high school are 90% and 85% and the ones not more than 10 years of quarrying experience are 70% and 52%, respectively. Accordingly it can be pointed out that most of the managers of two types of firms are relatively old, have high educational background, while quarrying experiences of building-stone firm managers are longer than that of aggregate firm managers. 2. Most of the management forms are social corporation(60%) for aggregate quarry firms and private management(76%) for building-stone firms. Average areas of permitted stone-pits of aggregate and building-stone quarries are about 2.86ha and 1.66ha respectively. That is, aggregate quarrying firms are carried on a larger scale than building-stone quarrying firms. 3. The yearly average product of aggregate quarrying firms has increased steadily from $88.961m^3$ in 1985 to $144.028m^3$ in 1988, while, in case of building-stone quarry firms, it has significantly increased from $4.155m^3$ to $19.462m^3$ from 1985 to 1987, but reduced to $13.400m^3$ in 1988. Unstable production activities of building-stone quarrying firms may require continuous government support. 4. Major cost items are equipment rental, depreciation, salaries, repair, maintenance for aggregate quarrying firms, and salaries, depreciation, fuel, tax for building-stone quarrying firms. The yearly average rate of return is about 9.7% for aggregate quarry firms and 2.6% for building-stone quarry firms. It can be pointed out that aggregate quarrying firms is better managed than building-stone quarrying firms. 5. The production elasticity of salary for aggregate quarrying firms is 0.495, that of employees is 0.559, and that of capital service is 0.513. The sum of the elasticities is 1.257>1. Fur building-stone quarrying firms, that of employees is 0.492, that of variable costs is 0.192, and that of capital service is 0.498. The sum of elasticities is 1.172>1, thus denotes the increasing returns to scale for both types quarrying firms. 6. The ratio of marginal value product to opportunity cost of empolyees is 2.54, that of variable costs is 3.62, and that of capital service is 1.45, in aggregate quarrying firms. That of employees is 2.47, that is variable costs was 2.34, and that of capital service is 19.67 in building-stone quarrying firms. Therefore the critical factors for more expansion of management scale in aggregate quarrying firms are variable cost and employees, and are capital service in building-stone quarry ing firms. 7. The break-even points of stone sales are about 0.587 billion won and 0.22 billion won in aggregate and building-stone quarrying firms respectively. The optimum sales Level for profit maximization are about 2.0 billion and 0.5 billion in aggregate and building-stone quarry firms respectively.