• Journal of the Korea Organic Resources Recycling Association
• /
• v.8 no.1
• /
• pp.77-82
• /
• 2000

Seven constructed and three natural tidal flats were compared to evaluate state-of- the-art of creation and restoration technology for tidal flats. parameters studied were physico-chemical and biological characteristics of soils and rate of respiration. The natural tidal flats had higher contents of silts, nitrogen and organic matter compared to the constructed ones. The natural ones had reductive Bone below 2 cm whereas the constructed ones had oxidative zone from the surface to below 20 cm. The bacterial population in the soil of the constructed tidal flats was one to two magnitudes lower than that in the natural ones. Biomass of macrobenthos and microbial respiration rate, however, were not different significantly between the natural and the constructed tidal flats. The purification capacity by diatom+bacterial+meiobenthos and macrobenthos in the constructed tidal flats was higher than that in the natural ones due to deeper permeable layer for purification in the constructed tidal flats. There was an exceptional constructed tidal flat with similar physico-chemical and biological characteristics to natural ones. Shearing stress to the surface of the tidal flat by the flow of seawater was as low as that of natural ones. These hydraulic conditions seemed to be a controlling factor on structures and functions of tidal flats. The control of hydraulic condition seemed to be one of the most important factors to create natural-like tidal flats.

• Journal of Korean Society of Environmental Engineers
• /
• v.39 no.10
• /
• pp.591-598
• /
• 2017

Power overshoot phenomenon was observed in microbial fuel cells (MFCs) used non-catalyzed graphite felt as cathode. Voltage loss in MFCs was mainly caused by cathode potential loss. Cheap stainless steel scrubber, which has high conductivity, and Pt/C coated graphite felt as cathode were used for overcoming power overshoot and reducing the cathode potential loss in MFCs. The MFCs used stainless steel scrubber showed no power overshoot even slow catholyte flow rate and produced 29% enhanced maximum current density ($23.9A/m^3$) than MFCs used non-catalyzed graphite felt while the power overshoot phenomenon was existed in Pt/C coated MFCs. Increasing catholyte flow rate resulted in disappearing power overshoot of MFCs used non-catalyzed graphite felt. In addition, maximum power density and current density of both MFCs used non-catalyzed graphite felt and stainless steel scrubber increased by 2-3.5 times. Cathode potential losses in all region of activation loss, ohmic loss, and mass transport loss were reduced according to increase of catholyte flow rate. Therefore, stainless steel scrubber has advantages that are economical materials as electrode and prevents power overshoot, leading to enhance electricity generation. In addition, increasing catholyte flux is one of great solution when power overshoot caused by cathodic overpotential is observed in MFCs.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.34 no.3
• /
• pp.473-480
• /
• 2007

The dentigerous cyst originates through alteration of stellate reticulum after amelogenesis has completed, with accumulation of fluid between the layers of the reduced enamel epithelium or between this epithelium and the tooth crown. Its incidence is relatively high on 10s or 20s of age and it is always related to the unerupted crown. Generally, it has no symptom, however, if the cyst is large or accompanied with pus formation, swelling and pain may occur. In radiographic findings, it shows impacted crown surrounded by well defined unilocular radiolucent lesion and occasionally displacement of adjacent teeth or root resorption. The goal of treatment is complete elimination of abnormal tissue preserving the tooth involved in the cyst. Enucleation and marsupialization are commonly used for the treatment. Marsupialization is the procedure which removes the partial portion of the cystic wall and connects with the oral mucosa. As the pressure in the cyst decreases, bone regeneration takes place in the defect area and cystic wall converts into normal mucosa. This procedure, however, is the most conservative procedure which allows the protection of adjacent important structures. If the eruption space is sufficient, then inducing the eruption of the permanent tooth in the cyst is also possible. In following cases, dentigerous cyst was diaganosed after clinical and radiographic examination. Marsupialazation was done to remove the cyst and induce the tooth, which was in the cyst, to erupt into the oral cavity.

• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.8
• /
• pp.877-885
• /
• 2013

A seawater pipe of the engine room in the ships is being surrounded with severely corrosive environments caused by fast flowing of the seawater, containing aggressive chloride ion and high conductivity etc.. Therefore, the leakage of the seawater from its pipe have been often occurred due to its local corrosion by aggressive chloride ions. Subsequently, its leakage area is usually welded by AC shielded metal arc welding with various electrodes. In this study, when the sea water pipe is welded with several types of electrodes such as E4301, E4311, E4313 and E4316, a difference of the corrosion resistance on the welding metal zones was investigated using an electrochemical method, observing microstructure, measuring polarization behaviors and hardness. The weld metal zone welded with E4313 electrode exhibited the lowest value of hardness compared to other weld metal zones. In addition, its zone indicated also the best corrosion resistance than those of other weld metal zones. Furthermore, all of the weld metal zones revealed a relatively better corrosion resistance than those of the base metal zones. and also showed higher hardness than the base metal zones.

• Korean Chemical Engineering Research
• /
• v.60 no.2
• /
• pp.217-222
• /
• 2022

It is very important to analyze the OCV change behavior during the open circuit potential holding (OCV holding) process, which accelerates the evaluation of the electrochemical durability of the PEMFC membrane. In this study, an empirical formula using the experimental data of three MEAs with different durability was created and compared. The durability evaluation time of the reinforced membrane MEA without radical scavenger inside the membrane was 383 h, and the durability evaluation time of the reinforced membrane MEA with radical scavenger inside the membrane was 1,000 and 1,650 h, respectively. The degradation of the membrane was divided into the reversible degradation that can be recovered by activation and the irreversible degradation that is not recovered. The irreversible degradation of the membrane was indicated by an increase in hydrogen permeability, and the change in hydrogen permeability was similar to the irreversible degradation constant c of all three MEAs. The initiation of irreversible deterioration without recovery is indicated by an increase in hydrogen permeability, and the OCV is not recovered due to an increase in hydrogen permeability, so the slope of the OCV recovery line (ORL) decreases, which can be confirmed by an increase in the constant c value of the empirical formula.

• Geophysics and Geophysical Exploration
• /
• v.5 no.4
• /
• pp.223-235
• /
• 2002

Since weak Bones or geological lineaments are likely to be eroded, there may develop weak Bones beneath rivers, and a careful evaluation of ground condition is important to construct structures passing through a river. DC resistivity method, however, has seldomly applied to the investigation of water-covered area, possibly because of difficulties in data aquisition and interpretation. The data aquisition having high quality may be the most important factor, and is more difficult than that in land survey, due to the water layer overlying the underground structure to be imaged. Through the numerical modeling and the analysis of a case history, we studied the method of resistivity survey at the water-covered area, starting from the characteristics of measured data, via data acquisition method, to the interpretation method. We unfolded our discussion according to the installed locations of electrodes, ie., floating them on the water surface, and installing them at the water bottom, because the methods of data acquisition and interpretation vary depending on the electrode location. Through this study, we could confirm that the DC resistivity method can provide fairly reasonable subsurface images. It was also shown that installing electrodes at the water bottom can give the subsurface image with much higher resolution than floating them on the water surface. Since the data acquired at the water-covered area have much lower sensitivity to the underground structure than those at the land, and can be contaminated by the higher noise, such as streaming potential, it would be very important to select the acquisition method and electrode array being able to provide the higher signal-to-noise ratio (S/N ratio) data as well as the high resolving power. Some of the modified electrode arrays can provide the data having reasonably high S/N ratio and need not to install remote electrode(s), and thus, they may be suitable to the resistivity survey at the water-covered area.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2002.09a
• /
• pp.139-162
• /
• 2002

Since weak zones or geological lineaments are likely to be eroded, weak zones may develop beneath rivers, and a careful evaluation of ground condition is important to construct structures passing through a river. Dc resistivity surveys, however, have seldomly applied to the investigation of water-covered area, possibly because of difficulties in data aquisition and interpretation. The data aquisition having high quality may be the most important factor, and is more difficult than that in land survey, due to the water layer overlying the underground structure to be imaged. Through the numerical modeling and the analysis of case histories, we studied the method of resistivity survey at the water-covered area, starting from the characteristics of measured data, via data acquisition method, to the interpretation method. We unfolded our discussion according to the installed locations of electrodes, ie., floating them on the water surface, and installing at the water bottom, since the methods of data acquisition and interpretation vary depending on the electrode location. Through this study, we could confirm that the dc resistivity method can provide the fairly reasonable subsurface images. It was also shown that installing electrodes at the water bottom can give the subsurface image with much higher resolution than floating them on the water surface. Since the data acquired at the water-covered area have much lower sensitivity to the underground structure than those at the land, and can be contaminated by the higher noise, such as streaming potential, it would be very important to select the acquisition method and electrode array being able to provide the higher signal-to-noise ratio data as well as the high resolving power. The method installing electrodes at the water bottom is suitable to the detailed survey because of much higher resolving power, whereas the method floating them, especially streamer dc resistivity survey, is to the reconnaissance survey owing of very high speed of field work.

• Koreanishche Zeitschrift fur Deutsche Sprachwissenschaft
• /
• v.7
• /
• pp.1-24
• /
• 2003

우리는 지금까지 독일어와 한국어 두 언어간의 오류분석을 논의해 왔다. 특히 언어유형학적인 측면에서 몇 가지 오류유형과 분석을 시도했다. 그 결과는 대체로 다음과 같이 요약될 수 있다. 독일어와 한국어가 서로 근본적으로 상반되는 언어현상과 더불어 약간의 공통성을 나타내며 일정한 유형을 나타낸다. 이는 두로 인간의 언어습득장치에 기인된 언어습득의 결정주의(Determinismus)에서 비롯될 것이다. 언어특성/문제의 체계성/규칙성 또는 일관성은 이를 반영한다. 거대한 언어자료 중에 극히 미미한 일부, 즉 언어최소량를 정복함으로써 그 효용성을 극대화할 수 있는 것은 매우 중요한 의미를 지닌다. 이를 연구 이용하는 경우에는 엄청난 효과와 가능성을 기대할 수 있을 것이다. (1) 독일어와 한국어의 학습 및 오류분석에서 가장 핵심적인 것은 언어유형학적으로 드러난 언어특성, 즉 전치성(독일어/영어)과 후치성(한국어)이다. 이를 토대로 형성된 대립적인 면과 공통적인 문제를 체계화하는 것이 역시 오류분석 문제의 관건이다. 또한 독일어가 아직 후치성 언어(한국어(TXV))에서 출발해서 전치성 언어(영어(SVX))로 발전/변화해 가는 과정, 즉 중간단계인 TVX에 머물고 있다는 사실이 중요한 의미를 지닌다. 즉 그들의 대극성과 유사성을 연결하는 실마리로 볼 수 있기 때문이다. (2) 일치(Kongruenz)/상관(Korrelation) 및 반복(Wiederholung) 현상, 그리고 격변화와 인칭변화 현상은 어순문제와 더불어 형태론적 문제를 통해 문법적인 확인수단으로 작용한다. 이들은 대부분 체계적/구조적으로 나타나기 때문에 학습자는 흔히 같은 유형에서 반복적으로 오류를 범하기 마련이다. 이를 극복하기 위해서 언어 유형학적 오류분석을 이해하고 또한 이를 통해 오류를 줄이거나 예방하는 학습이 필요하다. (3) 명사가 한정사구 안에서 성/수/격에 따라 변화하는 것과 동사가 동사구에서 주어의 인칭/수에 따라 인칭변화 하는 것은 우리 한국인에게는 아주 이색적인 현상이다. 이는 양면적인 수식구조에 대한 확인수단 및 원자가에 의한 강력한 형식위주 언어인 독일어와 전위적인 단일 수식구조와 부정형 동사를 특성으로 형성된 핵/최소문 언어간의 필연적인 적응관계 및 결과라고 볼 수 있다. 이 두 가지 유형 역시 언어특성에 따라 도식화/공식화 할 수 있다. (4) 괄호현상, 즉 으뜸머리(Hauptkopf)가 버금머리(Nebenkopf)와 분리하는 것은 우리 한국인에게는 아주 이색적인 언어현상이다. 한국어에는 머리의 이동이 없기 때문이다. 긴 구문에서 버금머리를 잊어버리거나 실수하는 것은 모든 괄호구문에서 예견되는 결과이다. 그러나 이는 정치성과 후치성 언어간의 전이 과정으로 이해될 수 있다. 으뜸머리가 원래의 자리를 박차고 소속 구/문의 앞자리로 도약한 것처럼 느껴지기 때문이다. (5) 전치 및 후치 수식이 유동적으로 작용하는 독일어는 전치 수식만으로 고정된 한국어보다 복잡하지만 균형적인 언어구조이다. 이러한 수식구조에서 한국인은 흔히 형태 및 어순에서, 그리고 번역에서 오류를 범하고 만다. (6) 그러나 가장 중요한 것은 아는 것을 제대로 이용하는 문제이다. 모국어/L2를 자유로이 말하고 쓸 때까지, 즉 언어습득에는 일체이 문법이나 도표/도식을 이용할 필요가 없다는 사실이다. 이는 17세기 서구의 이성주의 철학자들의 한결같은 경고이다. 오늘날 초고속 과학문명에서 더욱 빛을 발하는 것은 당연한 결과이다. 한 언어 속에 들어있는 문법체계를 익혀 가는 것이 곧 언어습득 과정이지만, 이를 달성하는 가능성 내지 첩경은 실제적인 언어자료와 체험이지 결코 문법이나 추상적인 개념적 접근이 아님을 웅변하고 있기 때문이다. 핵심적인 문제는 모국어교육에서도 최대 장점인 대화를 통한 언어연습/대화 기회를 최대한 보장하는 데 있다. 또한 언어간섭 현상을 조장하는 분위기를 막아야 할 것이다. 이러한 의미에서 교수법 개발이 외국어/L2 성공의 관건일 것이다. (7) 언어학습에서 오류를 극복하는 데는 일차적인 실제 상황에 부합하는 대화적인 연습, 그리고 효과적인 언어자료 접촉, 즉 독서와 모방이 중요하다. 이차적이고 직접적인 것은 통사(Syntax) 및 형태론(Morphologie)를 익힐 수 있는 말/문을 끊임없이 익히는 일이다. 이것이 또한 언어최소량을 충족시켜 언어습득에 이르는 첩경이다. 자연 생태적인 모국어 학습 또는 조정 및 제도적인 언어학습에서도 실제상황에 어긋나는 문법적인 체계에 얽매이는 도식 및 도표 위주의 텟스트는 일시적인 기대일 뿐이다. 인간의 언어습득장치를 이해하지 못한 결과이기 때문이다. 문법적인 개념위주 접근은 상당한 설명이 필요해서 절박한 자료와 체험까지 앗아가기 마련이다. 더구나 이를 위해 수준을 무시하고 모국어로 일관하여 벙어리와 문맹을 자초하는 것은 참으로 어리석은 일이다. 지식 정보화 시대 및 세계화 시대에는 무엇보다도 교육 및 언어정책이 국가 발전의 원동력이다. 특히 영어를 비롯한 외국어 학습능력과 학습방법은 매우 중요하다. 학습자에게 말하고 쓰는 기본 능력을 보장하는 것이 급선무이다. 이를 위한 작업의 하나가 바로 언어간의 오류분석일 것이다. 언어의 습득과 활용이 체계적이듯이 오류분석 역시 상당히 체계적이다. 그래서 인간의 언어습득과 언어습득장치를 두고 결정론(Determinismus)이 지배적이다. 이러한 의미에서 언어습득의 3대 요소, 즉 언어습득장치를 구비한 인간으로 태어나고, 해당 언어를 통한 일관된 언어체험/학습으로 언어최소량을 충족해야 한 언어를 정복할 수 있다는 것은 결정적인 사실이다. 학생고객에게 다가서는 책임교육으로 교육개방에 대비하는 일 역시 시대적인 상황이요 또한 결정적인 단계임엔 틀림이 없을 것이다.