• Economic and Environmental Geology
• /
• v.53 no.2
• /
• pp.213-220
• /
• 2020

When CO₂ foam is injected into the saline aquifer, the relative permeability of CO₂ decreases and its viscosity increases, thereby reducing mobility in porous media and ultimately improving CO₂ storge with enhanced sweep efficiency. In general, surfactants were used to fabricate CO₂ foam. Recently, nanoparticles have been used to form stable foam than surfactant. This paper introduces CO₂ storage technology using nanoparticle stabilized CO₂ foam. If the surface of the hydrophilic nanoparticles is partially modified into a CO₂-philic portion, the particles have an affinity for CO₂ and water, thus forming a stable CO₂ foam even in deep saline aquifers under high temperature and high salinity conditions, thereby it can be stored in the pores of the rock. In terms of economics, injection method using nanopaticle-stabilized CO₂ foam is more expensive than the conventional CO₂ injection, but it is estimated that it will have price competitiveness because the injection efficiency is improved. From an environmental point of view, it is possible to inject chemical substances such as surfactants and nanomaterials into aquifers or reservoirs for specific purposes such as pollutant removal and oil production. However, some studies have shown that nanoparticles and surfactants are toxic to aquatic animals, so environmentally proven substances should be used. Therefore, further research and development will be needed to study the production and injection of nanoparticle-stabilized CO₂ foam that are environmentally safe and economically reasonable.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.12
• /
• pp.608-613
• /
• 2019

NOx (Nitrogen oxide) in the exhaust gas from vehicle engines is considered one of the most harmful substances in air pollution problems. NOx is made when combustion occurs under high temperature conditions and EGR (exhaust gas recirculation) is normally used to lower the combustion temperature. As the EGR ratio increases, the NOx level becomes low, but a high EGR ratio makes the combustion unstable and causes further air pollution problems, such as CO and unburned hydrocarbon level increase. This study showed that fuel droplets could move more freely by the radiation of sonic wave for the stable combustion. In addition, the engine performance improved with increasing EGR ratio. As a basic study, the effect of sonic wave radiation on the velocity of fuel droplets was studied using CFD software. The results showed that the velocity of small droplets increased more under high frequency sonic wave conditions and the velocity of the large droplets increased at low frequency sonic wave conditions. In addition, an engine analysis model was used to study the effects of the increased combustion stability. These results showed that a 15% increase in EGR ratio in combustion resulted in a 45% decrease in NOx and a 10% increase in thermal efficiency.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.15 no.2
• /
• pp.119-127
• /
• 1986

The rheological properties of mayonnaise were studied with cylindrindrical viscometer. It was observed that mayonnaise showed pseudoplastic behavior, yield stress and time dependent characteristics. In the initial period of shear time, the decay of viscosity of mayonnaise was followed by a second-order kinetic equation. The influence of temperature on viscosity could be described by Arrhenius equation. The apparent viscosity of mayonnaise markedly increased with an rise in the concentration of egg yolk; and the emulsion was most stable at the concentration of 12%. At the concentration of $65{\sim}75%$ oil, the apparent viscosity was increased; the maximum value was reached at 75% oil, and above 75% oil, the remarkable decreased was observed. The size of oil drops was decreased with an increase in oil concentration of 75% oil. The apparent viscosity of mayonnaise was increased with an rise in water contents, while being decreased with one in the concentration of vinegar.

• Tunnel and Underground Space
• /
• v.21 no.5
• /
• pp.394-405
• /
• 2011

In this paper, we applied coupled non-isothermal, multiphase fluid flow and geomechanical numerical modeling using TOUGH-FLAC coupled analysis to study the complex thermodynamic and geomechanical performance of underground lined rock caverns (LRC) for compressed air energy storage (CAES). Mechanical stress in concrete linings as well as pressure and temperature within a storage cavern were examined during initial and long-term operation of the storage cavern for CAES. Our geomechanical analysis showed that effective stresses could decrease due to air penetration pressure, and tangential tensile stress could develop in the linings as a result of the air pressure exerted on the inner surface of the lining, which would result in tensile fracturing. According to the simulation in which the tensile tangential stresses resulted in radial cracks, increment of linings' permeability and air leakage though the linings, tensile fracturing occurred at the top and at the side wall of the cavern, and the permeability could increase to $5.0{\times}10^{-13}m^2$ from initially prescribed $10{\times}10^{-20}m^2$. However, this air leakage was minor (about 0.02% of the daily air injection rate) and did not significantly impact the overall storage pressure that was kept constant thanks to sufficiently air tight surrounding rocks, which supports the validity of the concrete-lined underground caverns for CAES.

• Tunnel and Underground Space
• /
• v.14 no.1
• /
• pp.69-77
• /
• 2004

Investigation of the time-dependent behavior of rock and the associated mechanisms are of key interest in long-term stability analysis of many engineering applications. In this study, creep tests were performed on Daejeon granite samples of 25.4mm diameter under uniaxial compression at varying stress levels. The effect of moisture was investigated by testing both air-dried and fully water-saturated samples. The creep behavior of Daejeon granite exhibited three distinctive stages of primary, secondary and tertiary creep. The ultimate strength of granite under a constant stress decreased considerably with time. Saturation and immersion of the test specimen in water markedly increased the total creep strain as well as the secondary creep rate. The experimental creep curves are fitted to Burger's model as well as two other empirical models suggested by previous researchers. A number of the parameters determined for each model are dependent on stress and influenced by the presence of water. Based on the experimental results, an empirical relation between the applied stress and the time-dependent strain is established separately for each air-dried and fully water-saturated Daejeon granite.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.19 no.3
• /
• pp.27-34
• /
• 2005

This paper presents a three phase Line-Interactive uninterruptible power supply(UPS) system with dual converter structure. The three phase UPS system consists of two active power compensator topologies. One is a series active compensator, which works as a voltage source in phase with the source voltage to have the sinusoidal source current and high power factor under the deviation and distortion of the source voltage. The other is a parallel active compensator, which works as a conventional sinusoidal voltage source in phase with the source voltage, providing to the load a regulated and sinusoidal voltage with low total harmonic distortion(THD). This paper presents in the series and parallel active compensator charging method depending on the amplitude of the source voltage. The conventional Line-Interactive UPS system is responsible for the DC charging and output voltage regulation at the same time, but UPS system with dual converter structure, a series active compensator can also charge the DC link. Therefore the charging algorithm using the series and parallel compensator needs to be researched. Therefore, by making the DC link voltage stable it can contribute the stability of series and parallel compensator. The simulation and experimental result are depicted in this paper to show the effect of the proposed algorithm.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.8 no.5
• /
• pp.23-33
• /
• 2008

Extra dosed bridge among the Cabled-stayed bridges have been increasingly built in korea in recently. But such bridges were often damaged by fire due to car collison. In this study Extra dosed bridges among the cabled-supported bridges are selected to analysis model frequently to be designed and/or constructed in recent and furture in this study. COSMOS FloWorks 2007 software are used for Heat Transfer Analysis and Thermal Stress Analysis. The safety of wire, HDPE pipe and stainless steel pipe are investigated. In the case of the constant of the temperature of the heat source, the significant three variables for the analysis are selected for study : (1) the distance between the fire-proof bulk head and the heat source, (2) wind velocity, (3) the height of the end of Stainless steel pipe.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.5
• /
• pp.18-27
• /
• 2005

Airfoils with improved longitudinal static stability were designed for a WIG craft through aerodynamic design optimization. The response surface method is coupled with NURBS-based shape functions and Navier-Stokes flow analysis. The procedure runs in the network-distributed design framework of commercial-code based automated design capability to enhance computational efficiency and robustness.Lift maximization design maintaining similar static margin to a DHMTU airfoil successfully produced a new airfoil shape characterized by pronounced front-loading and the well-known reflexed aft-camber line. Another airfoil design of lower variation in pitching moment during take-off showed weakened front-loaded characteristics and hence decreased lift slightly. Investigations using the present design methodology on an existing optimization result based on potential flow analysis and NACA-type geometry generation demonstrated significance of carrying various geometry generations and more realistic flow analysis with optimization.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2009.05a
• /
• pp.1939-1944
• /
• 2009

우리나라의 대표적인 도서지역인 제주도는 일반 내륙지역과 달리 지표수-지하수에 대한 연구가 지하수계에 대한 연구에 비해 미미한 실정이다. 제주도의 경우 내륙과 달리 대부분의 하천이 평상시 건천의 형태로 유지되며, 일정한 강우가 도달해야만 지표유출이 발생하는 경우가 많다. 이와 같은 하천특성은 내륙과 매우 상이하여 일반적으로 사용되는 유역 수문해석 방법으로는 수문성분의 정확한 산정을 기대하기 어렵고 이로 인해 지하수 해석에 있어서도 불확실성이 크게 증가하는 요인이 된다. 따라서 지표수의 정확한 거동과 지하수 해석의 불확실성을 줄이기 위해 유역개념의 물순환을 해석할 수 있는 지표수-지하수 연계 해석기술이 필요한 실정이다. 본 연구에서는 '삼다수 먹는샘물 환경영향조사'가 수행되어 비교적 정확한 지하수위 관측 자료가 확보되어 있고, 매우 제한적이기는 하나 하천의 유출량 조사가 수행된 바 있는 제주 표선 유역에 완전연동형 지표수-지하수 해석 프로그램인 SWAT-MODFLOW을 이용하여 지표수 유출성분과 지하수 유동변화를 동시에 고려한 분석을 수행하였다. 특히 MODFLOW의 Well 패키지와 SWAT의 물이동 옵션을 결합하여 표선유역의 198개 관측공의 양수를 동시에 모의하였다. 모의결과 지하수위는 비교적 양수에 비해 안정되게 유지되는 것을 알 수 있었고 이를 통해 현재 삼다수 공장의 양수량은 현재로서는 과다양수가 아닌 것으로 판단되었다. 현재의 양수량의 10배를 가정하여 모의를 한 결과, 지하수위는 함양에 의해 다시 회복되는 결과를 보이고 있어 이 지역의 실제 개발가능량에 대한 보다 심도있는 논의가 필요한 것으로 판단되었다. 나아가 이와 같은 분석을 통해 제주 지역의 전체의 지하수 개발가능량을 산정할 경우 제주지역의 지하수 관리방안이 새롭게 제시될 수 있을 것으로 기대된다.

• Journal of Korean Society of Water and Wastewater
• /
• v.31 no.6
• /
• pp.529-537
• /
• 2017

Membrane filtration process is an advanced water treatment technology that has excellently removes turbidity and microorganisms. However, it is known that it has problems such as low economic efficiency and the operating stability. Therefore, this study was to evaluate on the economical feasibility and operational stability comparison of membrane and sand filtration process in Im-sil drinking water treatment plant. For the economic analysis of each process, the electricity cost and chemical consumption were compared. In the case of electric power consumption, electricity cost is $68.67KRW/m^3$ for sand filtration and $79.98KRW/m^3$ for membrane filtration, respectively. Therefore, membrane filtration process was about 16% higher than sand filtration process of electricity cost. While, the coagulant usage in the membrane filtration process was 43% lower than the sand filtration process. Thus, comparing the operation costs of the two processes, there is no significant difference in the operating cost of the membrane filtration process and the sand filtration process as $85.94KRW/m^3$ and $79.71KRW/m^3$ respectively (the sum of electricity and chemical cost). As a result of operating the membrane filtration process for 3 years including the winter season and the high turbidity period, the filtrated water turbidity was stable to less than 0.025 NTU irrespective of changes in the turbidity of raw water. And the CIP(Clean In Place) cycle turned out to be more than 1 year. Based on the results of this study, the membrane filtration process showed high performance of water quality, and it was also determined to have the economics and operation stability.