• Journal of the Korean Society of Propulsion Engineers
• /
• v.8 no.4
• /
• pp.43-54
• /
• 2004

A visualization study was carried out to investigate the effects of phase difference qualitatively by examining wake pattern on the phase difference of a dragonfly type wing model. The model was built with scaled-up, flapping wings composed of a paired wing with fore- and hind-wings in tandem that mimick the wing form of a dragonfly. The present study was conducted by using the smoke-wire technique and an electronic device below the tandem wings was mounted to find the exact wing position angles. Uncertainties in wing position angle are about $\pm$$1.0^{\cire}$ and instantaneous wing positional angle varies from $-16.5^{\cire}$ to $+22.8^{\cire}$. The tests were made at phase differences between the fore-wing and hind-wing at $0^{\cire}$, $90^{\cire}$, $180^{\cire}$ and $270^{\cire}$. The results show that Karman vortex structures were produced at phase differences of $90^{\cire}$, $180^{\cire}$ and $270^{\cire}$, but Karman vortex structures were not observed at the phase difference of $0^{\cire}$.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.4 no.3
• /
• pp.275-284
• /
• 1999

Unbalanced source voltage in the 3-phase power system is decomposed into positive, negative and zero sequence c components. Also, assuming there is no neutral path in the system, the zero sequence component is not shown on the l load side. Therefore, in the unbalanced power system without neutral path. it is possible to provide balanced voltage to t the load side by compensating negative sequence component and also to regulate the voltage amplitude by controlling t the positive sequence component. In addition, the symmetrical components due to voltage unbalance can be effectively d detected on the synchronous reference frame by using dlongleftarrowq transformation. In this paper, an algorithm not only c compensating unbalanced source voltage by canceling the negative sequence component on the synchronous reference f frame but also maintaining load voltages constantly is proposed. Also a novel method for phase angle detection s synchronized by positive sequence component under unbalanced source voltage is suggested and this detected phase a angle is used for d-q transformation. The performances and characteristics of the proposed compensating system are a analyzed by simulation and verified through experimental results.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.37 no.4A
• /
• pp.214-218
• /
• 2012

In this paper, we reported on a high performance waveguide VCO(voltage controlled oscillator) for FMCW applications. The waveguide VCO consists of a GaAs Gunn diode, a varactor diode, and two bias posts with low pass filter(LPF). The cavity is designed for fundamental mode at 47 GHz and operated at second harmonic of 94 GHz center frequency. The developed waveguide VCO has 1.095 GHz bandwidth, 590 MHz linearity with 1.69% and output power from 14.86 to 15.93 dBm. The phase noise is under -95 dBc/Hz at 1 MHz offset.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.5
• /
• pp.1035-1039
• /
• 2012

In this paper, we developed a 94 GHz waveguide VCO(voltage controlled oscillator) using a GaAs-based Gunn diode and a varactor diode. The cavity is designed for fundamental mode at 47 GHz and operated at second harmonic of 94 GHz. Bias posts for diodes operate as LPF(low pass filter) and resonator. The fabricated waveguide VCO achieves an oscillation bandwidth of 760 MHz. Output power is from 12.61 to 15.26 dBm and phase noise is -101.13 dBc/Hz at 1 MHz offset frequency from the carrier.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.10
• /
• pp.1071-1078
• /
• 2003

In this paper, the planar, compact, and broadband phased array antenna system for IMT-2000 applications has been investigated. Two methods far designing a low-cost and low-complex beam-farming network are proposed. First, a new compact and broadband phase shifter with continuously controlled phase bits is designed by using parallel coupled lines. Second, its equivalent phase delay line is suggested to be capable of replacing the complex phase shifter with a reference phase bit on a phased array antenna. For the purpose of achieving the broadband system, in addition to the broadband phase shifter, a wide-slot antenna with a ground reflector is utilized as an element antenna. Therefore, the phased array antenna system has achieved compact size, broad bandwidth, and wide steering angle, although it has low complexity and low fabrication cost. The 3${\times}$1 phased array antenna system has a compact size of 1.6 λ${\times}$ l.6 λ, which is the sufficient ground plane of the wide-slot antenna. Experimental results present that the S$\_$11/ has less than 15 dB within the band and its radiation patterns on an E-plane have the capability of steering an antenna beam from -29$^{\circ}$to +30$^{\circ}$.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.1
• /
• pp.114-124
• /
• 2011

In this paper, we present a 2 GHz compact analog phase shifter with linear phase-tune characteristic. The compact phase shifter was designed base on a lumped all pass network and implemented using a ceramic substrate fabricated with thin-film technique. For a linear phase-tune characteristic, a capacitance of the varactor diode for a tuning voltage was linearized by connecting series capacitor and subsequently produced an almost linear capacitance change. The inductor and bias circuit in the all pass network was implemented using a spiral inductors for small size, which results in the size reduction to $4\;mm{\times}4\;mm$. In order to measure the phase shifter using the probe station, two CPW pads are included at the input and output. The fabricated phase shifter showed an insertion loss of about 4.2~4.7 dB at 2 GHz band and a total $79^{\circ}$ phase change for DC control voltage from 0 to 5 V, and showed linear phase-tune characteristic as expected in the design.

• Proceedings of the KIEE Conference
• /
• 2007.11b
• /
• pp.40-42
• /
• 2007

본 논문은 전기기기에 순간전압저하를 발생 하였을 경우 응동특성에 대한 영향을 계측하였다. 실험 방법은 AVR에서 Sag 발생기인 IPC에 입력한 후, IPC에서 전압의 크기와 시간을 조정하여 실험기기에 순간전압 강하를 발생하였다 실험기기는 PLC, 전자접촉기, 400[W]고압방전램프를 시험하였다. PLC시험에서 무부하와 정격부하에 따라 특성 의 변화가 생겼으며, 정격부하에서 Voltage Sag의 영향을 더 받았다 전자접촉기의 시험은 위상을 $0^{\circ},\;30^{\circ},\;60^{\circ},\;90^{\circ}$로 변화하여 Voltage Sag 발생시켜 계측하였으며, 위상의 변화에 따라 특성곡선이 변화하였다. 고압방전램프시험은 고압나트륨램프와 수은램프, 메탈헬라이드에 Voltage Sag를 발생시켰다. 방전램프의 시험결과 고압나트륨램프의 특성곡선이 가장 안정적으로 나타났다. 본 실험을 통해 순간전압저하에 대한 저압기기의 특성을 실험적으로 입증하여 전력시스템의 설계에 영향을 미칠 것이라 기대된다.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 2011.07a
• /
• pp.331-332
• /
• 2011

디저털 홀로그래피는 CCD를 이용하여 간섭 패턴을 기록하고 기록된 간섭무늬에 담겨진 물체의 정보로 입체영상을 복원하는 기술을 말하며, 현미경을 이용한 디지털 홀로그래피 기술은 3D 형상 복원이나 바이오포토닉스 등 다양한 분야에서 사용되고 있다. 하지만, 디지털 홀로그래피 기술은 촬영된 간섭패턴에서 픽셀의 위상차가 레이저 파장의 1/2 이상일 경우, 기존의 phase unwrapping 알고리즘으로는 해당 픽셀의 위상차이를 계산할 수 없는 문제가 있다. 이와 같은 문제를 해결하기 위해 본 논문에서는 다수의 홀로그램 영상과 깊이맵을 사용하여 완전한 형태의 깊이맵을 구하는 방법을 제안한다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.5 s.248
• /
• pp.595-601
• /
• 2006

Design space optimization using design space adjustment and refinement is used to optimize a knuckle in the suspension system of an automobile. This approach is a new efficient method for large-scale topology optimization by virtue of two reasons. First, design space adjustment including design space expansion and reduction is suitable for large-scale problems. Second, the design space refinement can be done globally or locally where and when necessary and thus is very effective in obtaining a target resolution with much less number of elements. Compliance minimization for a knuckle is considered with a realistic working condition to show the effectiveness and superiority of the new approach.

• Proceedings of the KIEE Conference
• /
• 2001.07d
• /
• pp.2060-2062
• /
• 2001

전기를 에너지원으로 사용하는 각 종 부하는 가정, 공장 및 상가 등에 널리 분산되어 있고, 여기에 전기를 생산 공급하는 발전기도 지역적으로 분산되어 병렬운전이 되고 있다. 새로운 발전기가 병렬운전에 참여하기 위해서는 기존 운전되고 있는 전력계통과의 전압, 주파수, 상회전, 위상이 일치하여야 한다. 만약 이들 조건이 갖추어지지 않은 상태에서 임의 병렬 접속을 시도하게 되면 해당 발전기는 물론 전체 계통에 충격과 손상을 초래할 수 있다. 양측의 전압과 주파수 비교는 상용 계측기를 사용하여 비교적 쉽게 할 수 있느나, 상회전 방향과 위상차의 판별에는 세심한 주의가 필요하다. 최근의 발전기에는 병렬 운전 조건을 자동으로 조정, 확인을 하는 장치를 채용하고 있으며 구체적인 회로구성과 동작원리를 여기에서 살펴보았다. 병렬 접속이 이루어진 후 발전기 별 전력 분담과, 계통 주파수 변동에 따라 자동으로 발전기 출력 제어가 이루어지는 기능이 터빈 조속기 측에 설정되어 사용된다.