• The Journal of the Korea institute of electronic communication sciences
• /
• v.13 no.1
• /
• pp.153-162
• /
• 2018

The importance of energy harvesting technique is increasing due to the elevated level of demand for sustainable power sources for wearable device applications. In this study, we developed an Energy Harvesting wearable Platform(EH-P) architecture which is used in the design of a multi-energy source based on TENG. The proposed switching circuit produces power with higher current at lower voltage from energy harvesting sources with lower current at higher voltage. This can powers microcontrollers for a short period of time by using PV and TENG complementarily placed under hard conditions for the sources such as indoors. As a result, the whole interface circuit is completely self-powered with this makes it possible to run of sensing on a Wearable device platform. It was possible to increase the wearable device life time by supplying more than 29% of the power consumption to wearable devices. The results presented in this paper show the potential of multi-energy harvesting platform for use in wearable harvesting applications, provide a means of choosing the energy harvesting source.

• Science of Emotion and Sensibility
• /
• v.25 no.4
• /
• pp.119-128
• /
• 2022

This study analyzes the effects of the number of angles and bends on resistance in a conductor-embroidered stitch circuit for efficient power transfer through a conductor of wearable energy harvesting to study changes in power lost through connection with actual solar panels. In this study, the angle of the conductive stitch circuit was designed in units of 30˚, from 30˚ to 180˚, and the resistance was measured using an analog Discovery 2 device. The measured resistance value was analyzed, and in the section of the angle where the resistance value rapidly changes, it was measured again and analyzed in units of 5˚. Following this, from the results of the analysis, the angle at which the tension was applied to the stitch converges was analyzed, and the resistance was measured again by varying the number of bends of the stitch at the given angle. The resistance decreases as the angle of the stitch decreases and the number of bends increases, and the conductor embroidery stitch can reduce the loss of power by 1.61 times relative to general embroidery. These results suggest that the stitching of embroidery has a significant effect on the power transfer in the transmission through the conductors of wearable energy harvesting. These results indicate the need for a follow-up study to develop a conductor circuit design technology that compares and analyzes various types of stitches, such as curved stitches, and the number of conductors, so that wearable energy harvesting can be more efficiently produced and stored.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.13 no.5
• /
• pp.1093-1100
• /
• 2018

Fast progress in miniaturization and reducing power consumption of semiconductors for wearable devices makes it possible to develop extremely small wearable systems for various application services. This results recent wearable applications to be powered from extremely low-power energy harvesters based on solar, piezo, and TENG sources. In most cases, the harvesters generate power in non-linear manner. Therefore, we implemented and experimented the device platforms to utilize natural frequency of around 3Hz. We also designed two-stage power storages and high efficiency conversion platform to consider such non-linear power harvesting sources. The experiment showed power generation of about 4.67mW/min from these non-linear sources with provision of stable energy storages.

• Journal of Convergence for Information Technology
• /
• v.11 no.11
• /
• pp.151-158
• /
• 2021

In this paper, we analyzed the latest research trends, challenges, and potential applications of next-generation solar cell materials in various industrial fields. In addition, future prospects and possibilities of Smart Textile Hybrid Energy Harvesting Devices that will supply electricity by combining with wearable IoT devices are presented. The hybrid textile energy harvesting device fused next-generation solar cells with tribo-piezoelectric devices will develop into new 'Convergence Integrated Smart Wear' by combining the material itself with wearable IoT devices in the era of the 4th industrial revolution. The next-generation nanotechnology and devices proposed in this paper will be applied to the field of smart textile with an energy harvesting function. And we hope it will be a paradigm shift that evolves into creative products which provide AI services such as medical & healthcare by convergence with the future smart wear industry.

• Proceedings of the KIPE Conference
• /
• 2019.07a
• /
• pp.233-235
• /
• 2019

에너지 하베스팅은 주변의 에너지를 수확하여 활용하는 기술로 이에 관련한 연구가 여러 분야에서 활발히 진행되고 있다. 마찰전기 나노발전기는 물리적인 움직임이나 마찰을 통해 발생되는 정전기를 이용하여 센서나 웨어러블 디바이스에 활용하는 에너지 하베스팅 기술 중 하나이다. 마찰전기 나노발전기는 ${\mu}W$(마이크로와트) 단위의 미소 전력을 생산함에도 불구하고, 다른 에너지 하베스팅 발전기들과 비교하여 큰 임피던스를 가지고 있어서 전력을 전달하기에 어려움이 있다. 또한 마찰전기 나노 발전기의 출력 전력은 Spike성 Pulse Train의 형태여서 다이오드 정류기가 필요하기 때문에, 정류기의 입력 임피던스와 마찰전기 나노 발전기의 출력 임피던스에 대한 분석을 이용한 임피던스 매칭 설계가 필요하다. 본 연구에서는 다이오드 정류기의 임피던스 모델을 유도하여 마찰전기 나노 발전기의 내부 임피던스와의 매칭을 통해 최대 전력을 전달하는 커패시터와 출력 부하 설계를 목표로 한다. 유도한 임피던스 모델에 대하여 실제 전력 실험을 통해 모델의 유효성과 정확성을 검증하고자 한다.

• Journal of IKEEE
• /
• v.25 no.1
• /
• pp.206-211
• /
• 2021

This paper proposes a Self-Reset Zero-Current Switching (ZCS) Circuit for thermoelectric energy harvesting. The Self-Reset ZCS circuit minimizes the operating current consumed by the voltage comparator, thereby reduces the power consumption of the energy harvesting circuit and improves the energy conversion efficiency by adding the self-reset function to the comparator. The Self-Reset ZCS circuit shows 3.4% of improvement in energy efficiency compared to the energy harvesting system with the conventional analog comparator ZCS for the output/input voltage ratio of 5.5 as a result of circuit simulation. The proposed circuit is useful for improving the performance of the wearable and bio-health-related harvesting circuits, where low-power and energy-efficient thermoelectric energy harvesting is needed.

• Journal of the Institute of Convergence Signal Processing
• /
• v.22 no.3
• /
• pp.134-140
• /
• 2021

This study relates to the development of a wearable device that can identify a personal location using low-power GPS and IMU based on energy harvesting. The energy harvesting technology using a piezoelectric device was applied for the development of personal location identification, and made it possible to acquire precise personal location data using GPS and IMU. As a result of the experiment, it was confirmed that GPS and IMU data were normally received. The personal location identification device can be prepared for an accident by identifying a personal location in a disaster area, etc., and the user will be able to use it easily regardless of time, place, and environment. It is expected that it can be used in various fields such as leisure and health care.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.44 no.6
• /
• pp.1224-1239
• /
• 2020

This study develops a wearable solar energy harvesting device that absorbs solar energy to generate and store power which can be used during outdoor activities by users even after dark. For this study, a prototype hat for outdoor activities at night was developed after the design of a solar energy harvesting generation, storage, and delivery system was designed that could store energy to light up LEDs. First, the main control board of the system was designed to integrate the charging function, the darkness detection circuit, the battery voltage sensing circuit, and the LED driving circuit in order to reduce bulkiness and minimize the connection structure. It was designed to increase convenience. Second, the system was designed as a wearable fashion product that connected each part with fiber bands and manufacturing it so as to be detachable from the hat. Third, charging and LED operation tests show that the battery is fully charged after 5 hours even in winter when the illuminance value is low. In addition, the LED operation experiment verified the effectiveness of a buffered system that could operate the LEDs for about 3 hours at night.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.14 no.1
• /
• pp.225-234
• /
• 2019

By using the Triboelectric nanogenerators, known as TENG, we can take advantages of high conversion efficiency and continuous power output even with small vibrating energy sources. Nonlinear energy extraction techniques for Triboelectric vibration energy harvesting usually requires synchronized active electronic switches in most electronic interface circuits. This study presents a nonlinear energy harvesting with high energy conversion efficiency to harvest and save energies from human active motions. Moreover, the proposed design can harvest and store energy from sway motions around different directions on a horizontal plane efficiently. Finally, we conducted a comparative analysis of a multi-mode energy storage board developed by a silicon-based piezoelectricity and a transparent TENG cell. As a result, the experiment showed power generation of about 49.2mW/count from theses multi-fully harvesting source with provision of stable energy storages.

• Composites Research
• /
• v.36 no.3
• /
• pp.224-229
• /
• 2023

Due to the increasing demand for wearable devices and miniaturization of various electronic devices, the trend of nanofabrication in IT devices is underway. In order to overcome the limitations of battery size and capacity, there has been a lot of research interest in energy harvesting technology, also known as triboelectric nanogenerator. AAO(Anodic Aluminum oxide) coated with fluoride is a structure that includes an anode layer with high properties in the triboelectric series, an dielectric layer that helps transfer the triboelectrically generated charges to the electrode without loss, and the electrode. For these reasons, AAO has been a lot of research on its application to frictional energy harvesting nanogenerators. In this work, we analyzed the correlation of AAO between the surface morphology and thickness of the insulating layer by utilizing aluminum oxide, which is advantageous for the application of triboelectric nanogenerators, and adjusting the thickness of the insulating layer.