• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.241-241
• /
• 2010

적외선 센서는 빛의 유무에 관계없이 물체 또는 인체에서 발산하는 적외선을 감지한다. 이러한 센서를 전자 및 디스플레이 시스템과 연동하면 열영상 시스템이 되는데, 이는 전방 감시, 플랜트 감시, 보안, 방범용으로 많이 사용되며, 특히 자동차 야간 운전자 보조용으로 사용되어 최첨단, 고부가가치를 지니고 있는 핵심부품이다. 비냉각형 적외선 센서인 마이크로볼로미터는 상온에서 작동하므로 극저온 Cooler가 불필요하며, 무게와 부피가 작아 각종 시스템에 부착가능하다. 특히 볼로미터형 적외선 센서는 용량이 적은 TE cooler로 상온으로 안정화를 시키며, 진공으로 유지되는 금속 또는 세라믹 패키지를 사용하게 된다. 본 연구에서는 마이크로 볼로미터용 진공패키지를 제작하여 패키지 조립 및 측정기술에 대해 조사하였다. 패키지는 금속재질인 kovar를 사용하여 제작되었고, 내부에 TE Cooler와 장수명 진공유지를 위한 getter, 그리고 온도센서 및 볼로미터 센서 칩을 장착하여 조립하였다. 패키지 Cap ass'y와 base envelop의 솔더링 공정은 약 $200^{\circ}C$에서 수행하였으며, evacuation system을 이용하여 5일 동안 패키지 bake-out 공정을 수행하였다. 이 후 getter를 활성화시키고, seal-off 공정으로 진공 기밀을 유지하였다. 진공 패키지의 기밀성은 $6{\times}10^{-9}\;std.cm^3/sec$로 기밀성을 유지하였다. 볼로미터 센서의 반응도는 $10^2\;V/W$ 이상을 나타내었으며, 탐지도는 $2{\times}10^8\;cm-Hz^{1/2}/W$를 나타내었다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.3D
• /
• pp.393-400
• /
• 2006

This study is intended to examine the characteristics of driver in the use of guide sign in urban areas. The good and bad points about guide sign based on landmark point and guide sign based on street name are demonstrated, and driver's preference between them are studied. The questionnaires given to general persons deal with general guide signs and road maps, and are designed to see if they can find out current location on the road map with guide sign. According to the results, drivers prefer guide sign based on street name to guide sign based on landmark. And guide sign based on street name took less time to find current location than with guide sign based on landmark.

• Proceedings of the KIEE Conference
• /
• 2006.07c
• /
• pp.1637-1638
• /
• 2006

HVAC 시스템은 쾌적하고 깨끗한 운전환경을 만들어 줌으로써 운전자에게 향상된 안락성과 안전성을 제공한다. 이때 센서는 시시각각으로 변화하는 차실 내외의 환경변화에 대한 정보를 검출하여 HVAC 제어 유니트에 제공한다. 현재 HVAC 시스템에 사용되고 있는 후막 가스센서는 소자 크기와 소비전력이 크고, 제작공정이 까다로워 생산성이 낮은 단점이 있다. 이와 같은 문제점을 해결하기 위해서 최근에는 초소형화, 저소비전력, 대량생산에 의한 저가격화가 가능한 MEMS 가스센서의 연구개발이 활발히 진행되고 있다. 본 연구에서는 MEMS 구조체를 이용한 마이크로 가스센서를 설계 및 제작하였고, 감도특성을 고찰하였다. 가스 감지막은 금속산화물 페이스트를 스크린 프린팅 하는 종래의 방법 대신 MEMS 구조체에 적용 가능한 sol-gel 프로세스에 의해 형성하였다. 또 가스 감지전극과 micro-heater를 동일 평면상에 제작, 공정을 간소화하여 저가화를 시도하였다. MEMS 구조체 위에 제작된 Pt 박막 micro-heater의 인가전압에 따른 발열특성을 조사한 결과, 발열온도가 인가전압에 비례하는 이상적인 선형성을 나타내었으며, $300^{\circ}C$의 동작 온도에 도달하기 위해 65mW 이하의 저전력 동작이 가능하였다. 가스 센서의 감도특성 확인 실험은 CO 가스 10ppm, NO 가스 0.3ppm을 기준으로 수행되었으며, CO 및 NO에 대해 Rs(sensitivity, 가스반응저항/초기저항) 값은 각각 0.753 과 2.416로 우수한 성능을 나타내었다.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.14 no.5
• /
• pp.23-29
• /
• 2015

In this study, human is the subject of driving a car, the actual EEG is a biological information in a number of reactions that are displayed while driving the vehicle by using a measuring device, occurs during travel of the road EEG to be collected, number of experiments the collected material on the basis of changes associated with running time, extracts the factors such as changes due to road geometry, and analysis was performed. The required changes in the EEG occurring during traveling experiment analysis alpha (${\alpha}$) waves, beta (${\beta}$) wave, after the primary extraction in the form of gamma (${\gamma}$) faction, the brain wave frequency of the entire period of the experiment change rate extracts, to calculate the change in frequency in response to EEG characteristics by applying the regression model to observe a learning effect in response to an increase in the number of experiments, as a result, depending on the number of experiments, EEG changes due to individual differences. The show, by repeatedly driving a section like this, it was possible to verify that comfortably travels driver accustomed in accordance with the stored road geometry and signal, safety facilities.

• The Journal of the Korea Contents Association
• /
• v.19 no.10
• /
• pp.560-567
• /
• 2019

South Korea, which has entered an aged society, is about to enter a super-aged society in 2025. With the increase of an aging population, traffic accidents by aged drivers have been settled as a social problem. Now, when Korea is facing a super-aged society to come, a study was conducted to prevent traffic accidents that occur while the elderly people are driving through a disaster prevention design. For theoretical research, this study examined the concept and necessity of disaster prevention design, the present condition of an aged society, aged drivers' physical and cognitive characteristics, and the policies related to the forms of traffic lights the elderly people see. In addition, to propose the design, this study investigated and analyzed the traffic safety forms and colors of the International Standards Organization and proposed the first and second forms of the design of traffic lights for the gradual improvement of the traffic lights based on that. The first improved design form is a plan for displaying a triangle, an arrow with a large area, and a quadrangle in the lens of the head of the existing traffic lights, and the second improved design form is a plan for introducing a new traffic light head and forming the traffic light with a bigger triangle, an arrow with a large area and a quadrangular lens. Since it has a visually clearer form than the present traffic lights, it is expected that aged drivers who have physical and cognitive characteristics due to aging can secure better visibility and conspicuity and that they can make better reflex responses than they can now, also in the change of driving environment (rain and heavy snowstorm, etc.). In addition, it is expected that this study would be a preceding study to prepare standard guidelines on traffic safety signs other than traffic lights to be prepared for the super-aged society.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.1D
• /
• pp.65-72
• /
• 2011

When an expressway intersects another expressway, a unique connector needs to be designed between the two consecutive exit ramps. In such a case, it is important to design a connector such that there is enough distance for drivers to find their way safely. A current design manual in Korea prescribes the minimum length of the connector as 240 m. In this research, we have suggested a method for calculating the minimum length of a connector in order to check the feasibility of the currently prescribed length. For this purpose, we have attempted to determine the total perception-reaction time and lane-changing time required by a driver. For determining the driver's perception-reaction time, we have used the driver's decision time in addition to the conventional 2.5 s of perception-reaction time for stopping sight distances. We have considered both the design speed and the average travel speed for the calculation of the length. To evaluate the accuracy of the new method, we have chosen four sites on expressways for which relatively high accident rates were recorded. As a result, we could verify that the current limit (240 m) was sufficient for drivers to be able to change lanes in the given specific geometry. However, the prescribed limit should be revised in case the drivers' decision time is considered to be their perception-reaction time. All new approaches for calculating the ideal length of a connector have been carried out by taking into account the design speed as well as the average travel speed. Owing to the characteristics of the specific geometry for two consecutive exit ramps and the large difference between the design speed and the average travel speed in the objective areas, it is more realistic to use the proposed method by keeping the decision time equal to a driver's perception-reaction time, in order to determine the ideal distance that should be maintained between two consecutive exit ramps.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.252-252
• /
• 2010

적외선 센서는 빛의 유무에 관계없이 주 야간 전방의 물체에서 발산하는 미약한 적외선(열선)을 감지하여 영상으로 재현하는 열상시스템은 자동차 야간 운전자 보조용 나이트 비젼, 핵심 시설의 감시 관리, 군수 등의 분야에 적용되어지고 있는 최첨단, 고부가가치를 지니고 있는 기술이다. 양자형은 센서 특성은 좋으나 냉각기(작동온도: $-196^{\circ}C$) 및 고진공 패키지인 dewar를 사용하는 반면에, 열형은 대부분 상온에서 동작되는 온도안정화를 위한 전자냉각모듈만을 구비하면 되므로 저가형으로 제작이 가능한 비냉각형 적외선 센서이다. 본 연구에서는 적외선 센서용 진공패키지 조립공정 및 패키지된 센서의 측정기술을 개발하였다. 금속 메탈패키지를 제작하였으며, 금속 진공패키지는 소자냉각용 TE Cooler와 장수명 진공유지를 위한 getter, 그리고 센서칩, 온도센서를. 장착하여 칩을 조립하였다. Cap ass'y와 base envelop의 솔더링 공정을 수행하였으며, 진공패키지의 진공유지를 위해 TMP를 이용하여 진공을 유지하고, 약 5일동안 패키지 bake-out을 수행하였다. 진공압력은 $10^{-7}\;torr$ 이하를 유지하였으며, getter를 활성화시키고, pinch-off 공정으로 조립 ass'y를 완성하였다. 진공 패키지의 기밀성은 He leak tester를 이용하여 측정하였으며, ${\sim}10^{-9}\;std.cm^3/sec$로 기밀성을 유지하였다. TE cooler를 작동한 온도안정성은 0.05 K 이하였다. 볼로미터 센서의 반응도는 $10^2\;V/W$ 이상을 나타내었으며, 탐지도는 $2{\times}10^8cm-Hz^{1/2}/W$를 나타내었다. 본 연구를 통하여 얻어진 결과는 향후 2차원 열영상용 어레이 검출기 및 웨이퍼수준의 패키징 공정에 유용하게 응용될 것으로 판단된다.

• Journal of Korean Society of Transportation
• /
• v.29 no.1
• /
• pp.71-79
• /
• 2011

Traditionally, a dynamic network model is considered as a tool for solving real-time traffic problems. One of useful and practical ways of using such models is to use it to produce and disseminate forecast travel time information so that the travelers can switch their routes from congested to less-congested or uncongested, which can enhance the performance of the network. This approach seems to be promising when the traffic congestion is severe, especially when sudden incidents happen. A consideration that should be given in implementing this method is that travel time information may affect the future traffic condition itself, creating undesirable side effects such as the over-reaction problem. Furthermore incorrect forecast travel time can make the information unreliable. In this paper, a network-wide travel time prediction model under incidents is developed. The model assumes that all drivers have access to detailed traffic information through personalized in-vehicle devices such as car navigation systems. Drivers are assumed to make their own travel choice based on the travel time information provided. A route-based stochastic variational inequality is formulated, which is used as a basic model for the travel time prediction. A diversion function is introduced to account for the motorists' willingness to divert. An inverse function of the diversion curve is derived to develop a variational inequality formulation for the travel time prediction model. Computational results illustrate the characteristics of the proposed model.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.9
• /
• pp.235-244
• /
• 2016

Automotive symbols are more widely needed for new, convenient driving devices in automobiles. Good automotive symbols should be detectable, identifiable at first glance, easily learned, recognizable, and produce quick responses after practice. In this paper, a methodology for developing and evaluating automotive symbols is suggested. It includes multiple tests, such as comprehension, perceptual quality, appropriateness, and integrated evaluation. 28 symbols were tested and evaluated by the suggested methodology for convenient driving systems, such as a lane departure warning system (LDWS), cruise control (CCS), and a collision warning system (CWS). Most of the KS R ISO 2575 symbols had higher scores of comprehension, perceptual quality, and appropriateness, but the sunroof and camera symbols had lower scores. Standard symbols with several new functions should be developed. This methodology could be useful for developing and evaluating automotive symbols.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.12
• /
• pp.603-611
• /
• 2020

Potholes on the road directly affect drivers' safety, satisfaction, and vehicle damage. Thus, real-time detection and response are required. Increasing frequency of patrols allows for potholes to be detected and responded to quickly, but this takes much manpower, money, and time. In addition, potholes have different occurrence characteristics depending on the rain conditions, so it is necessary to consider the optimal frequency from an economic and road-service perspective. Therefore, a quantitative analysis was done on the effects of rainfall on the occurrence characteristics of potholes. Information on the persistence, impact of rainfall intensity, and weather information was collected over a long period. Based on the results, a risk-based, optimized, and changeable road-patrol strategy is presented. The analysis results show that the probability of pothole occurrence increases by 2.4 times in rainy weather. Furthermore, the impact continues for 3 days even after the rain stops. The probability of pothole occurrence increases by 0.46% per 1 mm of rainfall, and the occurrence characteristics react sensitively to even a small amount of rain of around 1 mm. It was concluded that road patrol is required at least once every three days for an effect-free period, while twice a day is needed for the "sphere of influence" period to achieve a 95% reliability level.ys for effect-free period, while twice a day for sphere of influence period to satisfy 95% reliability level.