• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2012.05a
• /
• pp.502-506
• /
• 2012

The propulsion system of space launch vehicle generates thrust by supplying oxidizer and fuel to combustion chamber. KSLV-II 2nd stage engine, currently under development by KARI, is to use liquid oxygen as a oxidizer and JET-A1 as a fuel. The 2nd stage pump-fed engine is mainly composed of combustion chamber, turbo-pump and engine supply system. To develop liquid propulsion engine, the development of combustion chamber must be preceded. For performance validation of the combustion chamber, the designed and manufactured combustion chamber should be tested in combustion chamber test facility (CCTF). The detailed design for the planned CCTF in Naro Space Center was conducted. The oxidizer supply system modeling using AMESim was performed based on the results of the detailed design, and the oxidizer supply characteristics was analyzed in this paper.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.47 no.10
• /
• pp.738-746
• /
• 2019

Instead of hydraulic actuation systems, an electromechanical actuation system is more efficient in terms of weight, cost, and test evaluation in the thrust vector control of the 7-ton gimbal engine used in the Korea Space Launch Vehicle-II(KSLV-II) $3^{rd}$ stage. The electromechanical actuator is a kind of servo actuator with position feedback and uses a BLDC motor that can operate at high vacuum. In the case of the gimballed rocket engine, a synthetic resonance phenomenon may occur due to a combination of a vibration mode of the actuator itself, a bending mode of the launcher structure, and an inertial load of the gimbals engine. When the synthetic resonance occurs, the control of the rocket attitude becomes unstable. Therefore, the requirements for the stiffness have been applied in consideration of the gimbal engine characteristics, the support structure, and the actuating system. For the 7-ton gimbal engine of the KSLV-II $3^{rd}$ stage, the stiffness requirement of the actuation system is $3.94{\times}10^7N/m$, and the direct drive type electromechanical actuator is designed to satisfy this requirement. In this paper, an equivalent stiffness analysis model of a direct drive electromechanical actuator designed based on the stiffness requirements is proposed and verified by experimental results.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.125-129
• /
• 2009

The basic design of liquid rocket engine combustion chamber for a large space launch vehicle was described. It has vacuum thrust of 74.8 ton, vacuum specific impulse of 306.9 sec, chamber pressure of 60 bar, mass flow rate of 243.6 kg/s and combustion characteristic velocity of 1730 m/sec. The details of combustion performance and geometrical parameter were also given. The 75 ton combustion chamber consists of the combustor head with injector and the chamber/nozzle with regenerative cooling channels.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.1
• /
• pp.110-115
• /
• 2006

STSAT-2 is the first satellite which will be launched by the first Korean Space Launch Vehicle(KSLV). Ground station Baseband Control system(GBC) is now developed for STSAT-2. GBC has two functions. One is control data path between satellite control computers and ground station antennas(1.5M, 3.7M, 13M) automatically. The other is sending and receiving data between ground station and satellite. GBC is implemented by FPGA(Field-Programmable Gate Array) which includes almost all logic(for MODEM, PROTOCOL and GBC system control). MODEM in GBC has two uplink FSK modulators(1.2[kbps], 9.6[kbps]) and six downlink FSK demodulators(9.6[kbps], 38.4[kbps]). In hardware, STSAT-2 GBC is smaller than STSAT-1 GBC. In function, STSAT-2 GBC has more features than STSAT-1 GBC. This paper is about GBC structure, functions and test results.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.7
• /
• pp.592-600
• /
• 2007

Nowadays, researches for replacing material systems for cryotanks by composites have been being performed for the purpose of lightweight launch vehicle. In this paper, a type 3 propellant tank, which is composed of the composite developed for cryogenic use and an aluminum liner, was fabricated and tested considering actual operating environment, that is, cryogenic temperature and pressure. For this aim, liquid nitrogen (LN2) was injected into the fabricated tank and in turn, gaseous nitrogen (GN2) was used for pressurization. During this test procedure, strains and temperatures on the tank surface were measured. The delamination between hoop layer and helical one, was detected during the experiment. Several attempts were followed to investigate the cause analytically and experimentally. Thermo-elastic analysis in consideration of the progressive failure was done to evaluate the failure index. Experimental approach through a LN2 immersion test of composite/aluminum ring specimens suitable for simulating the Type 3 tank structure.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.50 no.2
• /
• pp.75-82
• /
• 2022

Nondestructive method to predict buckling load for the propellant tank of launch vehicle should be evaluated. Vibration correlation technique can predict the global buckling load of unstiffened cylindrical structure with geometric initial imperfection using correlation of natural frequency and compressive load from compressive test below the buckling load. In this study, vibration and buckling tests of a thin metal unstiffened propellant tank model subjected to internal pressure and compressive loads were performed and the test results were used for VCT to predict global buckling load. For the vibration test of thin structure, non-contact excitation method using a speaker was used. The response was measured with piezoelectric polymer(PVDF) sensor. Prediction results of VCT were compared with the measured buckling load in the test and the nondestructive global buckling load prediction method was verified.

• Aerospace Engineering and Technology
• /
• v.13 no.1
• /
• pp.55-62
• /
• 2014

FTSR(Flight Termination System Receiver) is a device that receives a ground command signal to abort a flight mission when abnormal conditions occur in the space launch vehicle. The secure tone command message shall consist of a series of 11 character tone pattern. Each character consists of the sum of two tones which taken from a set of 7 tones defined by IRIG(Inter-Range Instrumentation Group) in the audio frequency range. The MHA(Modified High alphabet) command adds a security feature to the secure tone command by using the predefined difference code. In order to check the function and performance of MHA FTSR, which is under development, for KSLV-II, the testbed should have functions of RF signal generation, receiver's output port monitoring, RS-422 communication and test data management. In this paper, we first briefly introduce MHA command and FTSR interface, and then show the LavVIEW based testbed include its H/W configuration, S/W implementation and test results.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.336-339
• /
• 2011

Hot-fire test facility is one of the most important infrastructure for thruster development and evaluation. During the past three years, Korea Aerospace Research Institute (KARI) and Hanwha Corporation have successfully performed the construction of hot-fire test facility for medium-scale monopellant thruster to the maximum 200N thrust level. In general, thruster hot-firing test should be performed in vacuum conditions to simulate space environment. The hot-fire test facility is divided into three subsystems, vacuum system, propellant supply system and data measurement & control system. The goal of this facility is to extend the capability from small thruster for satellite mission to medium-scale thruster for launch vehicle and lunar mission. In this paper, the progress and overview for thruster hot-fire test facility was introduced and test results were also presented.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.17 no.4
• /
• pp.56-62
• /
• 2013

The system analysis and design program of the liquid rocket engine has been developed for preliminary conceptual design process. The program analyzes the engine system and obtains optimal design variables by optimization methods such as genetic algorithm for the higher specific impulse and thrust to weight ratio using given input parameters and requirements. For the users' convenience, the GUI has been offered. The 3-dimensional model for the visualization of results has been interconnected with the CATIA program. The results are expected to be applied to the design process of the space launch vehicle for the analysis and selection of the propulsion system.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.17 no.2
• /
• pp.128-134
• /
• 2013

A 2-way solenoid valve regulates to maintain the pressure of ullage volume of propellant tanks when the command is given by control system for the liquid-propellant feeding system of space launch vehicle. The simulation model of solenoid valve for pressurization is designed with AMESim to verify the designs and evaluate the dynamic characteristics and pneumatic behaviors of valve. To improve the accuracy of the model, numerical flow analysis by using FLUNET code. The simulation results of their operating durations of valve by AMESim analysis are matched up with the results of experiments and validate valve model. Using the model, we analyze performance of valve; opening/closing pressure, operating time on various design factors of basic valve and control valve; geometrical size of valve seat, ratio of basic valve and sealing area.