• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.20 no.6
• /
• pp.254-261
• /
• 2010

Polycrystalline silicon (pc-Si) films are fabricated and characterized for application to pc-Si thin film solar cells as a seed layer. The amorphous silicon films are crystallized by the aluminum-induced layer exchange (ALILE) process with a structure of glass/Al/$Al_2O_3$/a-Si using various thicknesses of $Al_2O_3$ layers. In order to investigate the effects of the oxide layer on the crystallization of the amorphous silicon films, such as the crystalline film detects and the crystal grain size, the $Al_2O_3$ layer thickness arc varied from native oxide to 50 nm. As the results, the defects of the poly crystalline films are increased with the increase of $Al_2O_3$ layer thickness, whereas the grain size and crystallinity are decreased. In this experiments, obtained the average pc-Si sub-grain size was about $10\;{\mu}m$ at relatively thin $Al_2O_3$ layer thickness (${\leq}$ 16 nm). The preferential orientation of pc-Si sub-grain was <111>.

• Journal of the Korean Vacuum Society
• /
• v.9 no.4
• /
• pp.353-359
• /
• 2000

$(Bi_{0.15}Sb_{0.85})_2Te_3$ and $(Bi_{1-x}Sb_x)_2Te_3$ thermoelectric thin films were prepared by magnetron sputtering process, and their thermoelectric characteristics were investigated with variation of the sputtering condition and the $Sb_2Te_3$ content. The $(Bi_{0.15}Sb_{0.85})_2Te_3$ film, deposited by DC sputtering at $300^{\circ}C$ with rotating the Corning glass substrate at 10 rpm, was fully crystallized to $(Bi,Sb)_2Te_3$ phase with c-axis preferred orientation. This $(Bi_{0.15}Sb_{0.85})_2Te_3$ film exhibited the Seebeck coefficient of 185 $\mu$V/K which was higher than the values of other $(Bi_{0.15}Sb_{0.85})_2Te_3$ films fabricated with different sputtering conditions. With increasing the $Sb_2Te_3$ content, the Seebeck coefficient and electrical resistivity of p-type $(Bi_{1-x}Sb_x)_2Te_3$ (0.77$\leq$x$\leq$1.0) film were lowered. Among p-type $(Bi_{1-x}Sb_x)_2Te_3$ films, a maximum power factor of $0.79{\times}10^{-3}W/K^2-m$ was obtained at (Bi_{0.05}Sb_{0.95})_2Te_3$ composition..

• Korean Journal of Materials Research
• /
• v.10 no.6
• /
• pp.437-444
• /
• 2000

We investigated the effect of substrate temperature, chemical composition and post-deposition heat-treatment on the crystal structure and electrical transport of $La_{1-x}Sr_xMnO_{3-{\delta}}$(0.19${\leq}x{\leq}$0.31) thin films. As-prepared $La_{1-x}Sr_xMnO_{3-{\delta}}$ films grown at $500^{\circ}C$ by sputter techniques were found to have the pseudo-tetragonal system(a/c=0.97) and a highly preferential <001> orientation. The films were changed to be of the cubic system by post-deposition annealing at around $900^{\circ}C$. A main target of $La_{0.67}Sr_{0.33}MnO_3$ as well as auxliary targets of $La_{0.3}Sr_{0.7}MnO_3$ ceramics were co-sputtered to control the chemical composition of the film. The Sr content(x) of the film ranged from 0.19 to 0.31, depending on the number of the auxiliary target. When x increased from 0.19 to 0.31, the electrical resistivity of the film decreased and the transition temperature between metal and semiconductor shifted to higher temperature. With a magnetic field of 0.18 T, the magneto-resistance ratio (MR(%) = (${\rho}_o-{\rho}_H/{\rho}_H$) of the $La_{0.69}Sr_{0.31}MnO_3$ thin film was about 390%.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.10 no.6
• /
• pp.418-424
• /
• 2000

Pure $TiO_2$and 10 mol % Pb-doped $TiO_2(Pb_xTi_{1-x}O_2$(x = 0.1)) powder and thin films have been prepared by the sol-gel method. Titanium isopropoxide and ethanol are used for pure $TiO_2$, lead acetate trihydrate and titanium triisopropoxide monoacethylacetonate are used for Pb-doped $TiO_2$, respectively. Films are coated on p-type Si(100) wafer and ITO glass substrates by the sol-gel spin-coating method. The powder and multi-coated films are annealed at different temperature (400~$800^{\circ}C$) for phase formation and crystallization. TGA/DTA, XRD analysis, SEM and UV-visible transmission spectroscopy have been used to study the characteristics of the powder and films. XRD results show that the films are polycrystalline, anatase type and oriented predominantly to the A(101) plane. A slight shift in the d-spacing for the Pb-doped film indicates the incorporation of the Pb into $TiO_2$lattice. A shift of the absorption wavelength in the transmission spectrum towards longer wavelength has been observed about $Pb_xT_{1-x}O_2$(x = 0.1) thin film, which indicates a decrease in the bandgap of $TiO_2$upon Pb-doping.

• Korean Journal of Materials Research
• /
• v.10 no.4
• /
• pp.270-275
• /
• 2000

The Pt/YMnO$_3$/Y$_2$O$_3$/Si structure for metal/ferroelectric/insulator/semiconductor(MFIS)-FET was fabricated and effect of $Y_2$O$_3$layer on the properties of MFIS structure was investigated. The $Y_2$O$_3$ thin films on p-type Si(111) substrate deposited by Pulsed Laser Deposition were crystallized along (111) orientation irrespective of the deposition temperatures. Ferroelectric YMnO$_3$ thin films deposited directly on p-type Si (111) by MOCVD resulted in Mn deficient layer between Si and YMnO$_3$. However, YMnO$_3$ thin films having good quality and stoichiometric composition can be obtained by adopting $Y_2$O$_3$ buffer layer. The memory window of the $Y_2$O$_3$thin films with YMnO$_3$ film is greater than that of the YMnO$_3$ thin films without $Y_2$O$_3$ film after the annealing at 85$0^{\circ}C$ in vacuum ambient(100mtorr). The memory window is 1.3V at an applied voltage of 5V.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.7 no.6
• /
• pp.1313-1318
• /
• 2006

The mechanism fur the surface film formation was studied by in situ Atomic Force Microscopy (AFM) observation of a highly oriented pyrolytic graphite (HOPG) basal plane surface during cyclic voltammetry at a slow scan-rate of 0.5 mV $s^{-1}$ in 1 moi $dm^{-3}$ (M) $LiPF_6$ dissolved in a mixture of ethylene carbonate (EC) and diethyl carbonate (DEC). Decomposition of the electrolyte solution began at a potential around 2.15 V vs. $Li^+$/Li on step edges. In the potential range 0.95-0.8 V vs. $Li^+$/Li, flat areas (hill-like structures) and large swelling appeared on the surface. It is considered that these two features were formed by the intercalation of solvated lithium ions and their decomposition beneath the surface, respectively. At potentials more negative than 0.80 V vs. $Li^+$/Li, particle-like precipitates appeared on the basal plane surface. After the first cycle, the thickness of the precipitate layer was 30 nm. The precipitates were considered to be decomposition of the lithium salt ($LiPF_6$) and solvent molecules (EC and DEC), and to have an important role in suppressing further solvent decomposition on the basal plane.

• Journal of the Korean Vacuum Society
• /
• v.9 no.3
• /
• pp.197-206
• /
• 2000

The deposition characteristics of MOCVD Cu using the (hfac)Cu(1,1-COD)(1,1,1,5,5,5-hexafluoro-2,4-pentadionato Cu(I) 1,5-cyclooctadine) have been investigated in terms of the effects of carrier gas such as hydrogen and argon as well as the effects of H(hfac) ligand addition. MOCVD Cu using a hydrogen carrier gas led to a higher deposition rate and lower resistivity than an argon carrier gas system. The improvement in the surface roughness of the MOCVD Cu films and the (111) preferred orientation texture was obtained by using a hydrogen carrier gas. However, the adhesion characteristics of the films showed relatively weaker compared to the Ar carrier gas system, probably due to the larger amount of F content in the films, which was confirmed by the AES analyses. When an additional H(hfac) ligand was added, the deposition rate was significantly enhanced in the case of an argon + H(hfac) carrier gas system while significant change in the deposition rate of MOCVD Cu was not observed in the case of the hydrogen carrier gas system. However, the addition of H(hfac) in both carrier gases led to lowering the resistivity of the MOCVD Cu films. In conclusion, this paper suggests the deposition mechanism of MOCVD Cu and is expected to contribute to the enhancement of smooth Cu films with a low resistivity by manipulating the deposition conditions such as the carrier gas and addition of H(hfac) ligand.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.199-199
• /
• 2013

최근 단파장 광전 소자와 고출력 고주파 전자 소자에 대한 수요 때문에 넓은 밴드갭 에너지를 갖는 반도체에 관심이 많다. 이중에서, ZnO는 우수한 화학 및 역학적 안정성, 수소 플라즈마 내구성과 저가 제조의 장점 때문에 광전자 소자 개발 분야에 적합한 산화물 투명 전극으로 관심을 끌고 있다. 불순물이 도핑되지 않은 ZnO는 본질적으로 산소 빈자리 (vacancy)와 아연 격자틈새 (interstitial)와 같은 자체의 결함으로 말미암아 n형의 극성을 갖기 때문에, 반도체 소자로 응용하기 위해서는 도핑 운반자의 농도와 전도성을 제어하는 것이 필요하다. 본 연구에서는 박막 제조시 제어성, 안정성과 용이하게 성장이 가능한 졸겔 (sol-gel) 방법을 사용하여 사파이어와 석영 기판 위에 Cu가 도핑된 ZnO 박막을 성장시켰으며, 그것의 구조, 표면 형상, 평균 투과율, 광학 밴드갭 에너지를 계산하였다. 특히, Cu의 몰 비를 0, 0.01, 0.03, 0.05, 0.07, 0.1 mol로 변화시키면서 ZnO:Cu 박막을 성장시켰다. ZnO:Cu 졸은 zinc acetate dihydrate, 2-methoxyethanol (용매), momoethanolamine (MEA, 안정제)을 사용하여 제조하였다. 상온에서 2-methoxyethanol과 MEA가 혼합된 용액에 zinc acetate dihydrate (Zn)을 용해시켰다. 이때 MEA와 Zn의 몰 비는 1로 유지하였다. 이 용액을 $60^{\circ}C$ 가열판 (hot plate)에서 24 h 동안 자석으로 휘젓으며 혼합하여 맑고 균일한 용액을 얻었다. 이 용액을 3000 rpm 속도로 회전하는 스핀 코터기의 상부에 장착된 사파이어와 석영 기판 위에 주사기 (syringe)를 사용하여 한 방울 떨어뜨려 30 s 동안 스핀한 다음에, 용매를 증발시키고 유기물 찌꺼기를 제거하기 위하여 $300^{\circ}C$에서 10분 동안 건조시킨다. 기판 위에 코팅하는 작업에서 부터 건조 작업까지를 10회 반복한 다음에, 1 h 동안 전기로에 장입하여 석영 기판 위에 증착된 시료는 $550^{\circ}C$에서, 사파이어 기판은 $700^{\circ}C$에서 열처리를 수행하였다. Cu의 몰 비 0, 0.01, 0.03, 0.05, 0.07, 1로 성장된 ZnO:Cu 박막에 대한 x선 회절 분석의 결과에 의하면, 모든 ZnO:Cu 박막의 경우에 관측된 34.3o의 피크는 ZnO (002) 면에서 발생된 회절 패턴을 나타낸다. 이것은 JCPDS #80-0075에 제시된 회절상과 일치하였으며, ZnO:Cu 박막이 기판에 수직인 c-축을 따라 우선 배향됨을 나타낸다. 사파이어 기판 위에 증착된 박막의 경우에, Cu의 몰 비가 점점 증가함에 따라(002)면 회절 피크의 세기는 전반적으로 증가하여 0.07 mol에서 최대를 나타내었으나, 석영 기판 위에 증착된 박막의 경우에는 0.05 mol에서 최대를 보였다. 외선-가시광 분광계를 사용하여 서로 다른 Cu의 몰 비로 성장된 ZnO:Cu 박막에서 광학 흡수율 (absorbance) 스펙트럼을 측정하였으며, 이 데이터를 사용하여 평균 투과율을 계산한 결과, 투과율은 Cu의 몰 비에 따라 현저한 차이를 나타내었다. Cu의 몰 비가 0.07 mol일 때 평균 투과율은 80%로 가장 높았으며, 0.03 mol에서는 30%로 최소이었다. 광학밴드갭 에너지는 Tauc 모델을 사용하여 계산하였고, 결정 입자의 형상과 크기와의 상관 관계를 조사하였다.

• Korean Journal of Materials Research
• /
• v.9 no.12
• /
• pp.1263-1269
• /
• 1999

An FBAR(Solidly Mounted Resonator) was fabricated using reflector layers which prohibit the penetration of bulk acoustic wave into substrate. The SMR consisted of top and bottom electrodes(Al films), a piezoelectric layer (ZnO film), reflector layers(W/$Si_2$ films) and Si substrate. The electrodes were deposited by dc sputtering. The piezoelectric layer and the reflector layers were deposited by rf magnetron sputtering. The control of crystallinity, microstructures and electric properties of each layer was essential for attaining the optimum FBAR characteristics. Under the best deposition conditions for FBAR devices, the ZnO films had highly c-axis preferred orientation(${\sigma}=2.17^{\circ}$), resistivity of $10^4\;{\omega}cm$, and surface roughness of 10.6 ${\AA}$. On the other hand, the surface roughness of W and $Si_2$ films was 16 ${\AA}$ and 33 ${\AA}$, respectively, and the resistivity of Al film was $5.1{\times}10^{-6}\;{\Omega}cm$. The SMR devices were fabricated by the conventional semiconductor processes. In the resonance conditions of the SMR, the series resonance frequency (fs) and the parallel resonance frequency(fp) were 1.244 GHz and 1.251 GHz, respectively and the quality factor(Q) was 1200.

• Journal of the Korean Magnetics Society
• /
• v.8 no.6
• /
• pp.374-379
• /
• 1998

$Mn_1-xCr_xPt_3$ alloy films have been prepared by depositing (Mn, Cr)/Pt multilayers using a rf magnetron sputterer followed by heat treatment. Small and wide angle x-ray diffractometry, magnetic hysteresis loops and Kerr rotation angle spectra of the films have been measured and used to investigate structural, magnetic and magneto-optic properties of the films. The films had a crystal structure of ordered AuCu$_3$ type and the strong preferred orientation of a (111)plane parallel to the film surface. The saturation magnetization of the films was decreased with Cr content reaching almost zero near x=0.58 and then increased for further increasement of Cr content up to x=0.77 over that stayed almost constant. This indicated that Cr atoms were antiferromagnetically coupled with Mn atoms. The magnetic easy axis of MnPt$_3$(x=0) film was parallel to the film surface but those of the films with x$\geq$0.58 increased as Cr content increased reaching about 4 kOe at x=1(CrPt$_3$). The dependence of the Kerr rotation angle on the Cr content was similar to that of the saturation magnetization on the Cr content. The films with x=0.77 and x=1 showed the larger Kerr rotation angle at the wavelengths of near infrared compared to the magneto-optic recording medium, TbFeCo, currently being used.