• The Transactions of the Korean Institute of Power Electronics
• /
• v.4 no.3
• /
• pp.294-303
• /
• 1999

Resistance spot welding is commonly used for welding products of high quality because of clean welding and short w welding-time. But. conventional spot welders bring about the depreciation of welding products, iuespective of dynamic r resistance characteristics during welding time. This paper discussed dynamic resistance database implementation in t terms of welding performance improvement. On different welding conditions, we compared dynamic resistance, r respectively, about pure iron and Sn-Pb alloy on Copper. Also, it investigated the relation of tensile shear strength and d dynamic resistance in welded workpiece.

• Proceedings of the KSME Conference
• /
• 2005.11a
• /
• pp.127.2-127.2
• /
• 2005

• Proceedings of the KSME Conference
• /
• 2005.11a
• /
• pp.124.2-124.2
• /
• 2005

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.9
• /
• pp.1311-1316
• /
• 2010

In this study, straight slot welding was carried out using a 316L stainless steel test block, and numerical simulation of the slot weld process was performed using finite element analysis. Data on the residual stress were obtained at equally spaced points on the top surface of the test block along directions parallel and perpendicular to the welding direction. After electrolytic polishing of the top surface of the block, the residual stress was measured by the X-ray diffraction method. The calculated weld residual stresses were compared with the measured data, and they were in good agreement with the data. The weld residual stress distribution inside the plate was determined from the results of finite element analysis, and the characteristics of the distribution were discussed in detail in this paper.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1998.05b
• /
• pp.210-215
• /
• 1998

본 연구는 핫셀(Hot-cell)에서의 활용을 전제로 핵연료 봉단용접기술로 개발되고 있는 래이저(Laser) 용접기술을 핵연료봉 퍼복재인 Zircaloy-4에 적용하여 그 용접성에 대한 기초적 특성을 분석하고, 관련 용접변수들의 용접성에 미치는 영향을 알아보고자 하였다. 사용된 용접기는 평균출력 150W급인 펄스형 Nd:YAG 레이저 용접기였으며, 보호가스 (shielding gas) 종류와 유량(flow rate), 용접속도(travel speed), 초점위치(focus position), 빔 파워(beam power), 시편의 표면거칠기(specimen surface roughness) 등의 용접변수가 용입 깊이와 용접비드 폭, 기계적 특성, 그리고 용접결함에 미치는 영향을 조사하였다. 그 결과 용접변수로 범 파워 125W이상, 초점위치 2mm, 그리고 보호가스로는 He가스가 적절하였으며, 시편의 표면거칠기가 거칠수록 용입깊이가 깊었다. 본 연구를 통해 핵연료봉 피복재 Zircaloy-4의 레이저 용접시 신뢰성 있는 용접조건을 확립하기 위한 기초자료를 얻을 수 있었다.

• The Journal of Korean Academy of Prosthodontics
• /
• v.50 no.1
• /
• pp.53-60
• /
• 2012

Purpose: The purpose of this study was to compare Ni-Cr alloy property of gas-oxygen torch soldering and infrared welding using optical microscope and Electron Probe Micro Analyzer (EPMA). Materials and methods: Ni-Cr alloys were casted for specimens. Specimens had 3.0 mm diameter, 30.0 mm length and were divided into two groups. Each group had 4 specimens. One group was for gas-oxygen torch soldering and the other was infrared welding. Specimens were cut with low-speed disc and soldered each other with gas-oxygen torch and infrared machine. After soldering and polishing, specimens were observed at 3 points (soldering point, 5 mm distance point, 10 mm distance point) with optical microscope and analyzed 3 points (soldering point, 5 mm distance point, 10 mm distance point with EPMA. Results: The results of this study were as follows: 1. The observation of gas-oxygen torch soldering at 10 mm distance point under the optical microscope was not founded any specific surface properties, but some crack lines were observed at 5 mm distance and soldering point. 2. There were no crack lines were founded at the observation of infrared welding at 10 mm distance and 5 mm distance points under the optical microscope. However, at the 5 mm distance, the surface was not smooth enough compared with at 10 mm distance point. Some crack lines were observed at the welding point as well. 3. In the EPMA analysis of the gas-oxygen torch soldering, the component of Ni was increased by 4.5%, Cr was increased by 7.5% than that of the Ni-Cr alloy at the 10.0 mm distance. At the 5 mm distance, the component of Ni was decreased by 6.1%, Mo was increased by 9.0% than that of the Ni-Cr alloy but Cr was equally shown at the 5.0 mm distance. Only Ni was shown at the soldering point. 4. In the EPMA analysis of the infrared welding, the component of Ni was increased by 9.1%, Cr was increased by 0.4% than that of the Ni-Cr alloy but Al was equal at the 10.0 mm distance. At the 5 mm distance, the component of Ni was increased by 4.7%, Cr was increased by 4.7% and Al was increased by 0.1% than that of the Ni-Cr alloy. At the welding point, the component of Ni was increased by 8.8%, Cr was increased by 8.2% than that of the Ni-Cr alloy. Conclusion: From these results, at the 5 mm distance from the soldering point, the surface of the infrared welding was more smoother than that of the gas-oxygen torch soldering. On the EPMA analysis, the component of the specimens with infrared welding was more similar than that of the gas-oxygen torch soldering compared with the component of the Ni-Cr alloy.

• Proceedings of the KSR Conference
• /
• 2005.05a
• /
• pp.385-390
• /
• 2005

A specimen with residual stress due to welding was analyzed by three-dimensional cohesive zone model. The residual stress distribution was calculated by simulating welding process, and cohesive elements were located along crack propagation planes. Crack growth is possible since two planes of the cohesive element are separated beyond a maximum load carrying capacity. Stress fields around a crack tip are compared for specimens with and without residual stresses. Load-displacement curves and crack growth behaviors are also examined.

• Proceedings of the KWS Conference
• /
• 2002.05a
• /
• pp.222-223
• /
• 2002

• Proceedings of the Korean Nuclear Society Conference
• /
• 1997.05b
• /
• pp.555-560
• /
• 1997

원자력발전소의 전열관 보수용접기술은 원전시설의 수명연장을 목적으로 개발된 기술이며, 손상된 Inconel 600 전열관 내부에 Inconel 690 재질의 sleeve tube을 삽입한 후 용접을 하는 방법으로 수행된다. 증기발생기 전열관 sleeve 레이저 용접의 기본개념은 방사능지역 외부의 발진기로부터 발진된 레이저빔을 광섬유를 이용하여 장거리(200미터 이상) 전송하여 전열관 내부의 광학계 및 회전장치를 이용하여 전열관을 용접하는 방법이다. 본 연구에서는 펄스형 레이저의 용접 변수인 펄스폭, 반복율, 첨두출력 및 용접속도를 변화시키면서 용입상태를 측정하였고, 용접된 시편에 열처리 여부와 부식실험을 위한 C-ring 시편을 제작하여 caustic test를 위해 auto-clave vessel에서 1,000 시간 실험을 실시하였다.

• Proceedings of the KWS Conference
• /
• 2006.05a
• /
• pp.100-102
• /
• 2006