• Proceedings of the KWS Conference
• /
• 2001.05a
• /
• pp.136-138
• /
• 2001

• Proceedings of the KWS Conference
• /
• 1993.10a
• /
• pp.79-81
• /
• 1993

• Journal of the Korean Institute of Gas
• /
• v.5 no.1
• /
• pp.52-59
• /
• 2001

Factors to cause accidents were investigated through a systematic analysis of leakage accidents in welded LP-gas cylinder between 199 and 1999. As a result It was showed that most of leakage accident occurred at the pin-hole due to the localized corrosion on welded zone in cylinder. Accordingly, in this paper, we suggested that the problems of heat treatment condition in two-piece welded cylinder and substitute proposal for preventing the tearing of T zone in three-piece welded cylinder. Furthermore, corrosion rate on the weldment and base metal of welded LP-gas cylinder was evaluated using the electrochemical tests in acid rain and $3.5\%NaCl$ solution, Also, the poor adhesion and defects of film which was produced by electrostatic powder spray painting, while the LP-gas cylinder was manufactured, were analyzed using SEM(Scanning Electron Microscopy). And we proposed a optimum coating thickness of the cylinder.

• Proceedings of the KWS Conference
• /
• 1997.05a
• /
• pp.33-34
• /
• 1997

• Proceedings of the KWS Conference
• /
• v.43
• /
• pp.269-271
• /
• 2004

• Journal of Welding and Joining
• /
• v.12 no.1
• /
• pp.38-43
• /
• 1994

고강도 알루미늄합금은 중량이 가벼우면서 인장강도와 항복강도가 높고 가공성, 성형성이 좋아 항공기, 자동차, 선박 등 수송용 재료로 각광을 받고 있으며, 이 중 Al-Zn-Mg계(7000계) 알루미늄 합금은 용접 구조물용 경량소재로 활용범위가 높다. Al-Zn-Mg계 알루미늄 합금은 고온에서 용체화 처리후 저온으로 급냉시킨 재료를 자연시효 또는 인공시효처리를 하여 이 때 석출되는 시효 석출물에 의해 강도를 증가시킨 석출 경화형 합금이다. 그런데, 7000계열 알루미늄합금은 적절한 열처리 작업을 통해 최적의 기계적 성질이 얻어지도록 합금설계가 되어있기 때문에 구조물 제작시 용접에 의한 ARC 열을 받게 되면 열이력(thermal cycle)에 의해 모재의 미세조직이 변화하고 용접 결함이 발생하며 강도의 약화와 함께 내식성 등이 저하한다. 따라서 고강도 알루미늄합금의 용접성을 향상시키기 위해서는 용접부의 미세조직거동과 용접부에 발생하는 용접결함의 현상을 조사하여 용접용 고강도 합금에 필수적으로 요구되는 용접성에 대한 검토가 충분히 이루어져야 한다. 따라서 본 고에서는 알루미늄합금, 특히 7000계열 알루미늄합금에 주목하여, 용접방법, 각종 결함과 대책, 용접부의 시효경화와 응력부식균열 및 기계적 성질 등을 지금까지 보고된 각종 자료를 기초로 하여 3회에 걸쳐 기술하고자 한다.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.30 no.4
• /
• pp.295-301
• /
• 2010

Flow accelerated corrosion(FAC) of carbon steel pipes in nuclear power plants has been known as one of the major degradation mechanisms. It could have bad influence on the plant reliability and safety. Also detection of FAC is a significant cost to the nuclear power plant because of the need to remove and replace insulation. Recently, the interest of the guided wave testing(GWT) has grown because it allows long range inspection without removing insulation of the pipe except at the probe position. If GWT can be applied to detection of FAC damages, it will can significantly reduce the cost for the inspection of the pipes. The objective of this study was to determine the capability of GWT to identify location of FAC damages. In this paper, three kinds of techniques were used to measure the amplitude ratio between the first and the second welds at the elbow area of mock-ups that contain real FAC damages. As a result, optimal inspection technique and minimum detectability to detect FAC damages drew a conclusion.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.27 no.2
• /
• pp.97-104
• /
• 2007

An investigation has been made on the relationship between characteristics of Acoustic Emission (AE) signal in welding flaw and the stress corrosion defect in-service for the high pressure pipe steel. In order to tackle the problem of welding flaw in high pressure pipe, specimens were made by the aid of the application of both corrosion liquid usage and a quenching method after local heating. The amplitude of signal was $60{\sim}75\;dB$ in the territory which is suspected for defect, and the specimens which only have welding flaw showed gradients of 0.034, 0.034, 0.035. Moreover, there is a certain increase in gradient even though the differences are very slight. That is, corrosion specimens showed new gradients of 0.040, 0.039, 0.041 which put welding flaw and corrosion mechanism together. After pressurizing 3 minutes, AE signal has been detected from welding flaw easily in each part of the section. It is possible to predict the occurrence and also prevent the damage of stress corrosion crack which has characteristics of cleavage fracture.

• Proceedings of the KWS Conference
• /
• 2000.04a
• /
• pp.326-329
• /
• 2000

• Proceedings of the KWS Conference
• /
• 2002.05a
• /
• pp.185-187
• /
• 2002