• 제목/요약/키워드: 용접노치계수

검색결과 13건 처리시간 0.019초

비파괴법에 의한 압력용기 강 다층용접부의 균열선단에서 소성변형 역성장거동 평가에 관한 연구 (Study on Evaluation of Plastic Deformation Zone at Crack Tip for the Multi-Passed Weld Region of the Pressure Vessel Steel Using Nondestructive Method)

  • 나의균;이상근
    • 비파괴검사학회지
    • /
    • 제29권5호
    • /
    • pp.473-478
    • /
    • 2009
  • 본 연구에서는 비파괴법을 이용하여 압력용기 강 다층용접부에서 채취한 표준 샤르피 시험편의 균열선단에서 형성되는 소성변형 거동을 평가하였다. 모재, 후열처리재 및 용접재를 대상으로 시험편에 기계적인 노치를 가공한 후 예균열(pre-crack)을 낸 다음 4점 굽힘실험과 음향방출(acoustic emission: AE)실험을 동시에 실시하였다. 균열선단은 용접재외 후열처리재의 경우 용융선 근처에 위치하도록 하였다. 하중이 가해짐에 따라 균열선단에서 형성되는 소성영역의 크기는 응력확대계수를 이용하여 구했으며, 각 시험편에 대한 소성역의 크기와 음향방출 특성과의 관계는 축적된 AE 에너지 관점에서 고찰하였다. 시험편에 관계없이 탄성역역에서는 거의 AE신호가 감지되지 않았으며, 대부분의 AE신호는 소성변형 과정에서 발생하였다. 또한, 용접재가 모재와 후열처리재에 비해 AE신호가 훨씬 많이 발생하였다. 모재와 후열처리재 및 용접재의 균열선단에서 소성영역 크기와 축적된 AE에너지와의 관계는 현저히 다르게 나타났으며, 용접재의 AE counts는 모재와 후열처리재에 비해 많이 발생하였다.

초음파 에코파형의 웨이브렛 변환과 비파괴평가에의 응용 (Wavelet Analysis of Ultrasonic Echo Waveform and Application to Nondestructive Evaluation)

  • 박익근;박은수;안형근;권숙인;변재원
    • 비파괴검사학회지
    • /
    • 제20권6호
    • /
    • pp.501-510
    • /
    • 2000
  • 초음파 에코파형의 시간-주파수해석법으로 Wigner 분포와 웨이브렛 변환 등과 같은 새로운 신호처리 기법이 비파괴평가 분야에 널리 응용되고 있다. 본 연구에서는 웨이브렛 변환(wavelet transform)에 의한 음속과 감쇠계수의 주파수의존성과 초음파 결함신호의 잡음제거의 유용성 유무를 실험적으로 검증하였다. Gabor 함수를 웨이브렛의 기본함수로 사용하였다. 초음파의 에코파형에 포함된 각 주파수성분의 속도와 감쇠계수의 주파수의존성을 추정할 수 있었으며, 초음파탐상에서 결함의 검출능 향상과 결함크기 산정의 정량화에 접근하기 위해 웨이브렛 변환에 의한 S/N비 신호처리 시뮬레이션 결과를 오스테나이트강 스테인레스 용접부에 가공한 EDM 노치의 초음파 결함신호에 적용한 결과 임상에코를 저감하고 S/N비를 개선하는 것이 가능하였다.

  • PDF

SM45C와 SCM4의 마찰용접 및 피로특성에 관한 연구 (A Study on Friction Welding of SM45C to SCM4 Steel Bars and the Fatigue Properties)

  • 오세규;김부안;김선진;남상훈
    • 한국해양공학회지
    • /
    • 제2권2호
    • /
    • pp.112-121
    • /
    • 1988
  • A study on friction welding of carbon steel bar (SM45C) to chrome molybedenum steel bar(SCM4) is examined experimentally through tensile test, hardness test, microstructure test and fatigue test. so, this paper deals with optimizing the welding concitions and analyzing various mechanical properties about friction welds of SM45C to SCM4 steel bars. The results obtained are summarized as follows; 1) For friction welded joints of SM45C to SCM4 steel bars, the total upset(U)increases linearly with an increase of heating time ($t_{1}$) till 6s. 2) The determined optimum welding conditions are heating time ($t_{1}$)2s, upsetting time($t_{2}$), 3s, heating pressure($p_{1}$), 4kgf/$mm^{2}$(39.2MPa), upsetting pressure($p_{2}$, 8kgf/mm$^{2}$(78.4MPa) and rotating speed(N), 2, 000rpm when the total upset(U) is 3.4mm, resulting in a computed relationship between the joint tensile strength .sigma.$_{t}$ (kgf/mm$^{2}$and the total upset U(mm); .sigma.$_{t}$ =$0.21U^{3}$ - $3.38U^{2}$ +17.03U + 66.00 3) As the elongation is increased more and more, the fracture position becomes away from weld interface and the fractures are similar to those of SM45C. Fracture is taken place on SM45C side. 4) The weld interface of two dissimilar materials is mixed strongly, and the heat affected zone is about 2.0mm at SM45C while about 2.7 mm at SCM4 side. Therefore, the welded zone and heat affected zone are very narrow, comparing with those of the joints welded by the other welding methods. 5) The fatigue strengths at N=10$^{6}$ cycles of SM45C, SCM4 and friction welded joints are 23kgf/$mm^{2}$, 33kgf/$mm^{2}$(220.5 MPa), and 22.5kgf/$mm^{2}$(220.5MPa) respectively, and fracture at friction welded joint takes place at the side of SM45C. 6) The hardness of the friction weld interface is 3 times higher than that of base metal. 7) Fatigue strength of friction welded joint is higher than that of base metal. 8) Notch sensitivity factor of friction welded joint is lower than that of base metal.

  • PDF