• Journal of Welding and Joining
• /
• v.14 no.3
• /
• pp.20-28
• /
• 1996

고밀도 에너지를 열원으로 이용하는 고출력 레이저로는 CO$_{2}$레이저와 Nd;YAG 레이저가 있다. 레이저는 열가공임에도 불구하고 빔의 스폿경을 작게하여 높은 에너지 밀도($10^{6}$ W/cm$_{2}$ 이상)을 얻을 수 있으므로 열영향이 작고 작은 변형범위내에서 용접을 할 수 있고 입력 에너지의 제어성이 좋아서 미세한 용접이 가능하게 하고, 빔폭 대비 용입깊이가 커서 깊은 용접 비드가 형성되며, 자동화가 용이하다는 장점이 있다. 특히 Nd;YAG 레이저의 경우는 광 섬유를 이용하므로서 에너 지의 시간 분할 및 에너지 분할을 할 수 있는 등 분기 및 배치가 용이하며 펄스의 활 용을 극대화 할 수 있는 장점이 있다. 그러나, 결점으로도 맞대기 용접의 경우 갭의 여유가 판두께, 초점위치, 빔모드에 따라 변화하는데 이는 빔 스폿이 작음에 따른 장점이 단점으로 작용하는 경우이다. 레이저 용접부의 비드 폭이 좁기 때문에 인장 강도가 모재의 인장강도보다 밑도는 것도 겹쳐서 용접된 이음 부분의 인장강도에 있 어서 단점이 되고 있다.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2007.09a
• /
• pp.135-141
• /
• 2007

CSR(Common Structure Rules) enter into force on $1^{st}$ April 2006. Generally for double hull tankers of less than 150m in length, the Rules of the individual Classification Society are to be applied. Where high tensile stresses act through an intermediate plate, increased fillet welds or penetration welds are to be used longitudinal/transverse bulkhead primary support member end connections to the double bottom. If workers have begun to make used of established procedures between corrugated BHD and lower stool joint, first to welding on groove of face and then it has to gouging to blow on groove of root. So amount of man-hour increased, productivity secreased.

• Journal of the Society of Naval Architects of Korea
• /
• v.44 no.4
• /
• pp.425-438
• /
• 2007

In this paper, unsettled technical controversies concerning about fatigue strength analysis for FPSO, one of the representative floaters, associated with welding types, screening methods, fabrication tolerances, corrosion margins and Morison loads are described based on yard practices. Basic theory for stochastic fatigue analysis is introduced as detail as possible. In order to resolve large parts of the controversies, a new fully stochastic fatigue analysis program for FPSO is developed.

• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.200-205
• /
• 2000

Fatigue failure modes of load-carrying cruciform weld joints are dependent on the characteristics of the fatigue crack initiation and propagation from the weld toe or the weld root. In this study, constant amplitude fatigue tests on load-carrying fillet welded specimen carried out, and fatigue strengths were evaluated. Also, an attempt is made to develop a new analytical model with more accuracy to predict the fatigue crack propagation life of fillet welded cruciform joints of SWS 490B steels containing lack of penetration defects. From the result of this study, fatigue crack growth characteristics of load-carrying fillet welded cruciform joints, containing lack of penetration defects are found to be affected by the weld geometry, stress range and microstructures of the weld zone.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1997.05b
• /
• pp.555-560
• /
• 1997

원자력발전소의 전열관 보수용접기술은 원전시설의 수명연장을 목적으로 개발된 기술이며, 손상된 Inconel 600 전열관 내부에 Inconel 690 재질의 sleeve tube을 삽입한 후 용접을 하는 방법으로 수행된다. 증기발생기 전열관 sleeve 레이저 용접의 기본개념은 방사능지역 외부의 발진기로부터 발진된 레이저빔을 광섬유를 이용하여 장거리(200미터 이상) 전송하여 전열관 내부의 광학계 및 회전장치를 이용하여 전열관을 용접하는 방법이다. 본 연구에서는 펄스형 레이저의 용접 변수인 펄스폭, 반복율, 첨두출력 및 용접속도를 변화시키면서 용입상태를 측정하였고, 용접된 시편에 열처리 여부와 부식실험을 위한 C-ring 시편을 제작하여 caustic test를 위해 auto-clave vessel에서 1,000 시간 실험을 실시하였다.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.24 no.3
• /
• pp.275-281
• /
• 2004

Socket weldment used to change the flow direction of fluid nay have flaws such as lack of fusion and cracks. Liquid penetrant testing or Radiography testing have been applied as NDT methods for flaw detection of the socket weldment. But it is difficult to detect the flaw inside of the socket weldment with these methods. In order to inspect the flaws inside the socket weldment, a ultrasonic testing method is established and a ultrasonic transducer and automated ultrasonic testing system are developed for the inspection. The automated ultrasonic testing system is based on the portable personal computer and operated by the program based Windows 98 or 2000. The system has a pulser/receiver, 100MHz high speed A/D board, and basic functions of ultrasonic flaw detector using the program. For the automated testing, motion controller board of ISA interface type is developed to control the 4-axis scanner and a real time iC-scan image of the automated testing is displayed on the monitor. A flaws with the size of less than 1mm in depth are evaluated smaller than its actual site in the testing, but the flaws larger than 1mm appear larger than its actual size on the contrary. This tendency is shown to be increasing as the flaw size increases. h reliable and objective testing results are obtained with the developed system, so that it is expected that it can contribute to safety management and detection of repair position of pipe lines of nuclear power plants and chemical plants.

• Journal of Welding and Joining
• /
• v.30 no.1
• /
• pp.78-84
• /
• 2012

Due to the inherent dimensional uncertainty, tolerances accumulate in the final assembly. Tolerance accumulation has serious effect on the performance of ECV assembly. This paper proposes a method of tolerance accumulation analysis using Monte Carlo simulation, which includes welding process in assemble process. This method can predict the final tolerance distributions of the completed assembly with the prescribed statistical tolerance distribution of each part to be assembled. With the inclusion of welding, another dimensional uncertainties due to partial melting is to be accounted as well. Partial melting of projection height was included in the tolerance propagation analysis. Verification of the proposed method was performed by making use of Monte Carlo simulation. Monte Carlo simulation results showed promising results in that we can predict the final tolerance distributions in advance before actual assembly process of precision machinery.

• Journal of Welding and Joining
• /
• v.32 no.6
• /
• pp.47-55
• /
• 2014

The purpose of the study is to produce a mechanically improved weld and minimum variation of color through comparing unpulsed and pulsed GTAW (Gas Tungsten Arc Welding) for pure titanium (CP grade7) tube. Pulsed GTAW using 60 A peak current and 20 A background current (1:9) achieved the wider window of welding conditions having part and full penetration without burn-through than the case of unpulsed GTAW. Moreover, the pulsed welding reduced a discoloration on the back bead of the weld and the size of microstructures (basket weave and serrated ${\alpha}$). That is because the pulsed welding has it's a low heat input and severe weld flow induced from electric current variation. Furthermore, the pulsed welding improved the bending property of the welded Ti tube. The enhanced bending property for the pulsed GTAW was due to the insignificant discoloration on the weld surface with maintaining the metal polish.

• Journal of Welding and Joining
• /
• v.11 no.4
• /
• pp.44-56
• /
• 1993

The arc welding processes are substantially nonlinear, in addition to being highly coupled multivariable systems, Frequently, not all the variables affecting the welding quality are known, nor may they be easily quantified. From this point of view, decoupling between the welding parameters from the welding quality is very difficult, which makes it also difficult to control the welding parameters for obtaining the desired welding quality. In this study, a neural network based on the backpropagation algorithm was implemented and adopted for the selection of gas metal arc welding parameters of the fillet joint, that is, welding current, arc voltage and welding speed. The performance of the neural network for modeling the relationship between the welding quality and welding parameters was presented and evaluated by using the actual welding data. To obtain the optimal neural network structure, various types of the neural network structures were tested with the experimental data. It was revealed that the neural network can be effectively adopted to select the appropriate gas metal arc welding parameter of fillet joints for a given weld quality.

• Journal of Welding and Joining
• /
• v.13 no.1
• /
• pp.127-137
• /
• 1995

The possibility of new GMAW process using economic shielding gases including CO$_{2}$ gas was investigated on the effect of shielding gas on weldabilty. In the optimum welding condition using 600A power source, FCAW process showed low depositions rate, 114 g/min at 300A, but new GMAW using other mixed shielding gases exhibited high deposition rate, 208-224 g/min at 450A. TIME gas, Ar+CO$_{2}$ gas and Ar+CO$_{2}$+O$_{2}$ gas as a shielding gas were able to be used to the very high welding current(450A), moreover TIME gas and Ar+CO$_{2}$ gas showed the highest arc stability among shielding gases studied in this experiments. The weld penetration was performed by axial spray transfer mode of weld droplet. On the basis of workability, weldability and economic point of view, Ar mixture (80%Ar+20%CO$_{2}$) gas was recommended as a shielding gas for the development and application of new GMAW process. This shielding gas showed the low spatter, good weld quality, stable arc and low cost at the region of high welding current.